EZCOO EZ-EXSP12 User manual

User Manual
4K HDMI 2.0 1X2 Extender 165ft/50m
HDMI 4K@60Hz 4:4:4 8bit
EDID,IR and RS232
EZ-EXSP12
EZCOO, it’s easy, just cool!

OVERVIEW
UTP HDMI Extender EZ-EXSP12 supports HDMI 2.0 4K@60Hz 4:4:4 8bit,
HDCP2.2; Supports PoE, bi-directional IR, bi-directional RS232 and EDID
management,. It provides distribution 3 of 3840 x 2160@60Hz 4:4:4 video,
Two UTP outputs,one HDMI local loop output and Two-way IR up to
50m/165ft over a single Cat6a/7 cable. Simple cascade mode makes it easy
to apply to sport bar,Education, church, digital signage and other
environments.
FEATURES
Two UTP output extend UHD HDMI signal to remote HDMI display up
to 165ft/50m.
Supports HDMI 2.0 4K@60Hz 4:4:4 8bit,HDCP 2.2
EDID management.
Supports HDMI 4K@60Hz 4:4:4 8bit, up to 165ft/50m.
Support 3D, Support deep color 30bit, 36bit
Supports Blue-Ray 24/50/60fs/HD-DVD/xvYCC
Supports HDMI signal re-timing, never lose quality

Supports PoE, one power adapter powers on TX and RX without the
power supply,Supports bi-directional IR, either TV controls Blue-ray
DVD, or DVD controls TV via IR remote; So easy to set up control
system.
Supports bi-directional RS232, easy to connect to control system.
Dolby Digital Audio format, HDMI ports support Dolby Digital 7.1CH
Audio; DTS-HD Master Audio/Dolby-AC3/DSD/LPCM.
Multiple easy installation, include metal mounting ear, HOOK&LOOP
Plug and Play; No driver required; Installs in minutes
SPECIFICATIONS
1) HDMI version: Uncompressed HDMI 2.0
2) HDCP version: HDCP2.2
3) HDMI resolution: 4K*2K/1080p/1080i/720p/576p/576i/480p/480i
4) Support video format: 24bit/30bit,36bit deep color
5) Support audio format: Dolby true HD/DTS-HD/LPCM7.1/Dolby-
AC3/DSD
6) Max bandwidth: 600MHz Max baud rate: 18Gbps
7) Input/Output TMDS signal: 0.5~1.5Volts p-p(TTL)

8) Input/Output DDC signal: 5Volts p-p (TTL)
10) Max working current: 1.5A
13) Power adapter format: Input AC 100V-240V/ 50HZ,60HZ;
Output: DC12V/2A
14) Operating Temperature range: -15 to +55℃
15) Operating Humidity range: 5 to 90%RH (No Condensation)
16) Dimension (L x W x H): TX:130*94*20(mm);RX:83*58*22(mm)
17) Weight: 400g
Panel

INSTALLATION
1. Connect HDMI cable from HDMI source devices to HDMI1X2 Extender
input.
2. Connect network/Ethernet cable from UTP out (Transmitter) to UTP
input (Receiver).
3. Connect HDMI cable from HDMI output (Receiver) to HDMI input on
your display.

EDID SETTING
EDID switch on the front panel of transmitter
EDID SETTING
4K7.1
4K@30Hz_4:3:3_7.1CHz_3D
4K5.1
4K@60Hz_4:4:4_5.1CHz_3D
COPY
LEARNING EDID FROM HDMI OUT

HDCP SETTING
Test mode
Strip out HDCP(Default)
Normal mode
HDCP1.4/2.2 pass through
Scaler 1080P
Down scaling from 4K to1080P
TROUBLE SHOOTING
1. POWER: Make sure all devices are powered on.
2. Make DVD PLAYER 24P/24Hz ON.
3. DEVICES: Make sure picture can be shown normally when connecting
HDMI source to display devices directly.
4. HDMI CABLE: Plug in and out HDMI 2.0 cable or change another HDMI
cable. When transmit HDMI 4K@60Hz (4:4:4) signal,HDMI 2.0

certificated cables is required.
5. NETWORK CABLE:
5-1 Please use Cat5e/6a/7 cable, don` t suggest use Cat5.
5-2 Make sure CatX cable is less than 165ft.
5-3 Make sure the two connectors of one CatX cable are same standard
(EIA/TIA 568B).
6. COMPATIBILITY: Please test other source and display devices to
determine whether it is a compatibility issue.
7. IR SIGNAL: Make sure the IR cables are correctly installed according to
the diagram above. (IR Bi-direction Control)
7-1 Check if the IR emitter head is secured over the center of the IR
window of source device. This position maybe discrepant if you use
different sources, try to adjust the position if the signal is weak.
(or you can refer to the user manual of your source device to confirm
the exact position of IR window)
7-2 Pay attention to the control angle and distance as below: The
control signal will be better when your controller is pointed at the IR
receiver head directly.