Ezee Glow MZEZPUBL16 User manual

Pulse and Pulse Widescreen Electric Fire Range
OWNERS MANUAL
Model Numbers: MZEZPUBL16, MZEZPUBL25
AC 220-240V, 50Hz 1000-1200W
WARNING
Please read the entire owner’s manual, including all safety information,
before plugging in or using this product. Failure to do so could result in fire,
electric shock, or serious personal injury.
CAUTION
Keep this owner’s manual for future reference. If you sell or give this
product away, make sure this manual accompanies this product.
Rev A
@ezeeglow
@ezeeglowelectricfires
Be sure to upload your fire image using #ezeeglow and tag Ezee
Glow on Facebook or Instagram to feature on our social media!

2
IMPORTANT SAFETY INFORMATION!
WARNING
When using electrical appliances basic precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons, including the following:
⚫Read all instructions before using this heater.
⚫This heater is hot when in use. To avoid burning, do not touch hot surface. If provided, use
handles when moving this heater. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least 1 m from the front of the heater and keep them
away from the sides and rear. In order to avoid overheating, do not cover the heater.
⚫Extreme caution is necessary when any heater is used near children or the infirm and
whenever the heater is left operating and unattended.
⚫Always unplug heater when not in use.
⚫Do not operate any heater with a damaged cord, plug or after the heater malfunctions, has
been dropped damaged in any manner. Return heater to authorized service facility for
examination, electrical or mechanical adjustment, or repair.
⚫Indoor use only, do not use outdoors.
⚫This heater is not intended for use in bathrooms, laundry areas and similar indoor locations.
Never locate heater where it may fall into a bathtub or other water container.
⚫Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar
coverings. Arrange cord away from traffic areas, where it will not be tripped over.
⚫To disconnect heater, turn controls to off, then remove plug from outlet.
⚫Do not insert objects into ventilation or exhaust openings, as this may cause an electric shock,
fire, or damage the heater.
⚫To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a bed, where openings may become blocked.
⚫A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, or
flammable liquids are used or stored.
⚫Use this heater only as describes in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to persons.
⚫DANGER-HIGH Temperatures may be generated under certain abnormal conditions. Do not
partially or fully cover or obstruct the front of this heater.
⚫This appliance is not intended for use by persons with reduced physical, sensory or capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
⚫CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this
appliance must not be supplied through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off by the utility.

3
WARNING
WARNING: This heater is not equipped with a device to control the room temperature. Do not use this heater
in small rooms when they are occupied by persons not capable of leaving the room on their own, unless
constant supervision is provided.
Children less than 3 years old should be kept away from the appliance. Children aged from 3 –8 years shall
only switch on the appliance, provided it is properly installed, have been given instruction on how to use it
and understand the hazards involved. Children aged 3 –8 shall not plug in, clean, or perform maintenance
tasks on the appliance.
· CAUTION —Some parts of this product can become very hot and cause burns. Particular attention
must be given when children and vulnerable people are present.
ELECTRICAL CONNECTIONS –UK PLUG WIRING INSTRUCTION
• If the plug must be changed because it is not suitable for your socket, or due to damage, please
follow the wiring instructions shown below.
• The wires in the mains lead are coloured in accordance with the following code:
BROWN: LIVE (L)
BLUE: NEUTRAL (N)
GREEN/YELLOW: EARTH (E)
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, please see below:
• The BLUE wire is the NEUTRAL and must be connected to the
terminal which is marked with the letter N or coloured BLACK.
• The BROWN wire is the LIVE and must be connected to the
terminal that is marked with the letter L or coloured RED.
• The GREEN/YELLOW must be connected to the terminal which
is marked E or the earth symbol or coloured GREEN or
GREEN/YELLOW.
• Always ensure that the cord grip is positioned and securely
fastened.
• WARNING: THIS APPLIANCE MUST BE EARTHED.
• If a 13A (BS1363) fused plug is used it must be fitted with
a BS1362 13A fuse. If in doubt consult a qualified
electrician.
IMPORTANT SAFETY INFORMATION!

4
Preparation
This product includes a GLASS panel. Use extreme caution when handling. Failure to
do so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Check
the parts list and make sure you have all the parts you need. Please recycle all packaging material at
your local recycling center or use your household recycling bin.
You will need the following tools (not included): Phillips screwdriver.
Parts and Hardware
A –Electric fire
B –Remote Control
C- Instruction Manual
D- Artificial logs and Crystals
E- Charred wood flakes

5
Specification and Dimension
Product Dimensions
Model Number
A
B
C
D
E
F
G
H
MZEZPUBL16
19”
48.2cm
23.2”
59cm
5.5”
14cm
15”
38cm
21.7”
55cm
2.6”
6.6cm
12.5”
31.6cm
15.5”
39.4cm
MZEZPUBL25
25”
63.5cm
23.8”
60.3cm
5.5”
14cm
15”
38cm
21.7”
55cm
2.6”
6.6cm
17”
43.1cm
15.5”
39.4cm

6
Installation and Assembly
Your appliance is usually fitted into a standard 16”x 22”fireplace opening. If you’re using an electric
suite, select a suitable location that is not susceptible to moisture build-up. It must be located enough
distance away from curtains, furniture, and high traffic areas. If fitted in a fireplace, chimney must be
blocked off prior to use. See below for more info.
NOTE: Follow all relevant local and national electrical codes.
MINIMUM CLEARANCE TO COMBUSTIBLES
Measurements are taken from the glass front.
Bottom 0" Top 11.8" (300mm) to mantel
Sides 0" Top 11. 8" (300mm) to ceiling
Back 0" Front 36”(1000mm) to vent
MINIMUM MANTEL CLEARANCES
WARNING
WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE
HEAT RESISTANT TO PREVENT DISCOLOURATION.

7
Fuel-bed effect installation
1. The appliance must be installed in its final location before the crystals, artificial logs and charred
wood flakes are installed.
2. Remove the glass front and safely store it to one side for now. Figure 1.
3. Disperse the crystals evenly on the fuel-bed tray in a side-to-side motion. Figure 2. Next, using
the same side to side technique, disperse the majority of the charred wood flakes onto the surface of
crystals. Save some for later.
4. Place the artificial logs on the surface of the crystals. Figure 3. To enhance the bed further,
disperse the remainder of the charred wood flakes in and around each log.
5. Finally, when content with your fuel-bed, re-fit the glass screen, switch the fire on and relax.
Figure 1. Figure 2.
Figure 3.

8
Operation
Please read the entire owner’s manual, including all safety information, before
plugging in or using this product. Failure to do so could result in electric shock, fire,
serious injury, or death.
Power
Plug the power cord into a 220-240V 50Hz outlet (see IMPORTANT SAFETY INFORMATION on
Pages 2 and 3). Make sure the outlet is in good condition and the plug isn’t loose. NEVER exceed
the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit.
Methods of Operation
The electric fire operated by the remote control. See figures below.
Before operating, please review the IMPORTANT SAFETY INFORMATION on Pages 2 and 3.
Front View
\
Remote Control
Power switch
Heat Vents

9
Power Switch Operation
ON
OFF
ON (l). Enables all functions.
OFF (O). Turns off all functions.
1. Press ON (l). Power turns on. All
functions are enabled.
2. Press OFF (O). Power, flame effect, and
all functions turn off.
Remote Control Operation
BUTTON
FUNCTION
ACTION & INDICATION
POWER
ON: Enables remote control. Turns on
flame effect.
OFF: Disables remote control. Turns off
flame effect.
1. Press once, indicator light turns on.
Power turns on. All functions enabled.
2. Press again, flame effect turns off.
Power and all functions turn off.
COLOUR
COLOUR button: Adjusts the flame/ fuel-
bed colour.
NOTE: Colour effect stays on until power
button is turned off. Colour flame/ fuel-bed
effect must be on for heater to turn on.
1. Press once, indicator light turns on.
Colour changes.
2. Press again, until desired colour is
selected.
BRIGHT-
NESS
Brightness button: Adjusts brightness.
NOTE: Flame effect stays on until power
button is turned off. Flame effect must be
on for heater to turn on.
1. Press once, indicator light turns on.
Brightness changes.
2. Press again, until desired brightness is
selected.

10
HEATER
HEATER button: Turns heater on and off.
NOTE: The heater only works when the
flame effect is on. If the flame effect is off,
the heater will not turn on.
NOTE: To prevent overheating, the heater
blows cool air for 10 seconds before the
heater turns on, and after it turns off.
NOTE: Heater overrides room temp
control.
1. Press once, indicator light (H1) turns on.
Fan blows cool air for 10 seconds. Low
heat (H1) turns on and blows warm air.
2. Press again, indicator light changes to
H2. High heat (H2) turns on and blows
hot air.
3. Press again, indicator light turns off. Fan
blows cool air for 10 seconds, then turns
off.
TIMER SETTINGS ON REMOTE CONTROL
: Timer: Displays current day, time, and week. Press to enter
or confirm timer settings.
: Settings: Press to move to next step. Press to confirm week
timer.
: Back: Press to clear timer settings. Press to return to the
previous step.
: Up and Down Press to increase/ decrease certain settings.
LCD Screen
Weekday
Mon, Tues, Wed, Thurs, Fri, Sat, Sun
Note: The functions can
only be adjusted when the
related letters or digits are
flashing.
Note: Calibrate the timer
to current time before
entering the weekly
settings.
Time Display
Current Time / Timer From 00:00 to 24:00
NOTE: 00-12:00 is AM / 13:00-24:00 is PM
TEMP
TEMPERATURE button: Turns heater on
and off to maintain room at a certain
temperature automatically.
NOTE: Press & hold the button for 5
seconds, the temperature setting will
switch from ℃to ℉and vice versa.
P 1. Press once, indicator light turns on.
Temperature is preset at 18 ℃.
1. 2. Press again, until desired room
2. temperature is selected.

11
1 Set current day and time
1. Press once. When “MON” (Monday) begins flashing, use to select the current day.
2. Press . When the hour digits begin flashing, use to select the current hour.
3. Press again. When the minute digits begin flashing, use to select the current minute.
4. Press again. The current time is now set.
2 Set ON/OFF time and temperature on a weekly cycle
1. Press . When “MON” begins flashing, press 3 times. When “ON” begins flashing, use to select
the desired hour and minute to turn on the heater. Press to clear the digits and shut down “ON” timer.
2.
Press . When “OFF” beginsflashing, use to select the desired hour and minute to turn off the heater.
Press at any time to clear the digits and shut down “OFF” timer.
3.
Press again. When “18” begins flashing, use to select the desired temperature for Monday.
4.
Press again. When “TUES” appears on the screen and “ON” begins flashing, use to select the desired
hour and minute to turn on the heater forTuesday.
5.
Press again. When “OFF” begins flashing, use to select the desired hour and minute to turn off the
heater forTuesday.
6.
Press again. When “18” begins flashing, use to select the desired temperature forTuesday.
7. Repeat steps 1 to 6 to set the “ON/OFF” time and temperature for Wednesday, Thursday,Friday,
Saturday, and Sunday.
8.
Press or to finish, ensuring to aim the remote control at the receiver located in the middle of the
appliance. The appliance will “beep” once to confirm your settings have been saved successfully.
Open window warning
If the room temperature decreases by 10 degrees within 3 minutes, the appliance will assume there is an open window
nearby. To conserve energy, the heater will automatically switch from High Heat to Low Heat, or if the heater is already at
Low Heat, it will turn off completely.
When switching from High Heat to Low Heat, the appliance will beep 3 times and the digital display will flash “88” 3 times
before displaying the existing heating status.
When switching from Low Heat to Off, the appliance will beep 3 times and the digital display will flash “88” continuously.
Toreset the heating function, see “operating remote control” section. A simple switch of off then on should work.
note:
If the temperature was previously set, those digits will be shown instead of“18”.
note:
The timer can only be adjusted in 30-minute intervals (i.e. 00:00 - 00:30; 00:30 - 01:00, etc.)

12
NOTICE
When the heater is first turned on, a slight odor may be present. This is normal and
won’t occur again unless the heater is un-used for a long period of time.
NOTICE
To improve operation, aim the remote control at the front of the fireplace. DO NOT
press the buttons too quickly. Give the unit time to respond to each command.
Temperature Limiting Control
This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe
temperature, the heater will automatically turn OFF. To reset:
1. Unplug the power cord from the outlet.
2. Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes.
3. Inspect the fire unit and make sure all vents are free from dust or lint. If they are clogged, use a
vacuum to clean the vent areas.
4. With the POWER switch in the OFF position, plug the power cord back into the outlet.
5. If the problem continues, have your outlet and wiring inspected by a professional.
Remote Control Battery Information
•This remote control uses Two AAA batteries (NOT included).
NEVER dispose of batteries in fire. Failure to observe this precaution may result in
explosion.Dispose of batteries at your local hazardous material processing center.

13
Cleaning
ALWAYS turn the heater OFF and unplug the power cord from the outlet before
cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in
electric shock, fire, or personal injury.
NEVER immerse in or spray with water. Doing so could result in electric shock, fire,
or personal injury.
Metal:
•Buff using a soft cloth, slightly dampened with a citrus oil-based product.
•DO NOT use brass polish or household cleaners as these products will damage the metal trim.
Glass:
•Use a good quality glass cleaner sprayed onto the cloth or towel. Dry thoroughly with a paper
towel or lint-free cloth.
•NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Vents:
•Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
Plastic:
•Wipe gently with a damp cloth and a mild solution of dish soap and warm water.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Maintenance
Risk of electric shock! DO NOT OPEN any panels. No user-serviceable parts inside!
ALWAYS turn the heater OFF and unplug the power cord from the outlet before
cleaning, performing maintenance or moving the fire unit. Failure to do so could result in
electric shock, fire, or personal injury.
Electrical and Moving Parts:
•The fan motors are lubricated at the factory and will not require lubrication.
•Electrical components are integrated in the fireplace and are not serviceable by the consumer.
•Store unit in a clean dry place when not in use.
Care and Maintenance

14
WEEE：
Meaning of crossed–out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities. Contact your local government for information regarding the
collection systems available. If electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the groundwater and get into the food
chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to
take back your old appliance for disposal, free of charge.

15