Factoryfurniture SCROLL Manual

Factory Furniture Ltd |The Stableyard |Coleshill |Swindon SN6 7PT |T [phone] |F [phone]
[email protected] |www.factoryfurniture.co.uk
We reserve the right to change specification without notice. © 2016 Factory Furniture Ltd
SCROLL Picnic Set
Operation & Maintenance Manual

Introduction
Design
Design, shop drawings and development by Factory Furniture Ltd
Manufacture
Factory Furniture manufactured components. Products are assembled in Factory workshops, checked and dispatched ready
for installation. Replacement products or components thereof should be ordered direct from Factory Furniture Ltd
Copyright
The design copyright for the product and drawing copyright remains the sole property of Factory Furniture Ltd
General Specifications
Table Bench
Metric length 2000mm | width 760mm | height 750mm* Metric length 2000mm | width 295mm | height 450mm*
Imperial length 6’ 6½” | width 2’ 6” | height 2’ 5½”* Imperial length 6’ 6½” | width 11½” | height 1’ 5½”*
*Not including +300mm below ground level for sub-surface root fix *Not including +300mm below ground level for sub-surface root fix
Fixing Centres 1200mm (3’ 11”) Fixing Centres 1200mm (3’ 11”)
Approx Weight 106kg Approx Weight 44kg
Picnic Set (Combined)
Metric length 2000mm | width 1615mm | height 750mm*
Imperial length 6’ 6½” | width 5‘ 3½” | height 2’ 5½”*
* Not including +300mm below ground level for sub-surface root fix
Fixing Centres 1200mm (3’ 11”) x 1320mm (4’ 4”)
Approx Combined Weight 194kg
Detailed Material & Finish Specifications
Table & Bench Slats
• Manufactured from FSC®certified hardwood
• Profiled and left untreated as standard (oil or microporous woodstain treatment available on request)
• Supported on and bolted to legs
Legs
• Manufactured from stainless steel - satin polished
• Stainless steel plate at top of each base for fixing to table / bench top
• Stainless steel ‘T‘ bar at foot of each base for better anchorage in foundation pad
• Root fixed 300mm (1’) below ground level
General Maintenance (Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of timber table/bench slats and frame - check all items for superficial or physical damage.
Three Monthly
Clean all items as detailed below check all fixings are seated correctly; inspect timber for serious damage and splinters.
Six Monthly
Secure all fixings; full clean as detailed below; check that table and benches are firmly secured to the ground
Specific Maintenance Details
FSC Timber
Clean with a stiff brush once per year, especially in more exposed locations, in order to prevent a verdigris type build up on
the timber surface. Ideally this should be completed in early spring. During the cleaning stage, all exposed timber surfaces
should be inspected for splits and splinters. Any splinters and graffiti should be removed and the surface sanded with 100
grit sandpaper in order to remove any uneven / sharp edges or surfaces.
During the first few months after installation the tannin naturally occurring in the timber may leach out and cause a brown
staining on the bases. This may be removed with a light solution of household bleach and water.
Stainless Steel (polished stainless steel only)
Clean as required, but at least every three months, using a stainless steel polish and a lint free cloth. To remove ground in
dirt, a stainless steel finishing pad may be required.
2SCROLL PICNIC SET specification
)6&&
5HVSRQVLEOH
)RUHVW0DQDJHPHQW

Repairs
FSC Timber
For light damage, please see section on specific maintenance details above. For instances of heavy damage, the timber item
should be replaced. Please order against the part number reference in the reordering section towards the end of this manual.
Stainless Steel
Light damage (surface scratches etc.) can be removed using an emery pad (240 grit) and freeing oil such as ‘WD40’. Care
should be taken to follow the direction of the brushing grain. It is recommended that a trial repair be carried out on an
unimportant surface first. No corrosive cleaners or other abrasives should be used. Any contamination, particularly carbon
steel scuffs from vehicles, should be quickly removed to avoid corrosion.
Heavy Damage
In the event of serious damage to any component, replacements should be ordered from Factory Furniture Ltd. In this event
(or if the product needs to be disassembled for any reason), please contact Factory Furniture for detailed technical advice.
Reordering / Spares
Part No. Item Description
P2010 / 01 1 no. Table slat set (not including legs) - (2 no. outer slats & 3 no. inner slats total)
P2010 / 02 1 no. Bench slat set (not including legs) - (2 no. slats)
Instructions For Reordering
If possible, please specify job name or number at the time of reordering to enable identification of details such as the original
species of timber used, stainless steel finishes and polyester powder coat colours etc. In any event where either, additional
orders are required, or spares and replacements are required please contact Factory Furniture Ltd. Using the part numbers
given above as reference should help us to process your enquiry more efficiently.
Note - All fittings required to assemble ordered parts will automatically be included in the order.
AutoCAD Drawing List
FF2010 / 01 SCROLL PICNIC SET PICNIC TABLE - GENERAL ARRANGMENT DRAWING
FF2010 / 02 SCROLL PICNIC SET PICNIC BENCH - GENERAL ARRANGMENT DRAWING
FF2010 / 03 SCROLL PICNIC SET PART DETAIL DRAWINGS
FF2010 / 04 SCROLL PICNIC SET SETTING OUT DRAWINGS
Contacts
Factory Furniture Ltd,
The Stableyard,
Coleshill,
Swindon.
Wiltshire SN6 7PT
U.K.
Tel [phone]
Fax [phone]
Email [email protected]
Web www.factoryfurniture.co.uk
3SCROLL PICNIC SET repairs

Ground
level
Foundation pad
400x400x400mm
in C20 concrete
(recommendation only)
750
7602000
1200 Ctrs
300
660 Ctrs
450
295130295 130
660 Ctrs
800400 400 260400 400400 260
1615
Installation Instructions
ALL INSTALLATION WORKS TO BE CARRIED OUT BY COMPETENT PERSONNEL - INSTALL AS
COMPLETE UNIT.
Scroll Picnic Set
Scroll Picnic Set
1. Dig holes for foundation pads (see illustration) and position table and benches in holes in correct orientation with bases
central in each hole. For correct heights table and bench legs should sit 300mm below finished ground level (table
750mm & bench 450mm above FGL)
2. Carefully pour concrete for each pad. Check table and benches are level and maintain at correct height and vertical until
concrete sets (at least 24 hours).
IMPORTANT NOTE:
Ensure that stainless steel is protected during site cutting of stone – contamination from disc cutters will produce corrosion on
stainless steel components.
4SCROLL PICNIC SET installation