VOLUME • STANDBY • BAL.OUT • EFFECTS LOOP GETTING STARTED
____________________________________________________________________________________________________________________________________________________________
16 5
VOLUME - The VOLUME knob controls
all volume in the unit, controlling the
poweramp and line output.
STANDBY - The STANDBY switch on
the front mutes the all outputs; line out,
effect send, the balanced output and speaker
outputs, except for TUNER OUT which
always is active
BALANCED OUTPUT - Is a high quality
balanced output. Designed electronically
floating, which means the output always
will adapt itself when sending to an
asymmetrical device such as an unbalanced
input, to keep a correct level with high
noise immunity.
The balanced output functions as a line
box for connecting to PA consoles or to
studio or broadcast recording units.
Lifting ground is a great aid in many
occasions. When required, set the Gnd Lift
switch as the front panel to inner position
to disconnect the ground from the output.
The Post Eq switch at the front selects the
signal source. In the inner position this
switch selects the overall sound included
effects, otherwise an uncolored sound is
taken immediately from the input, with the
same level as the instrument.
EFFECT LOOP - The unit is provided
with an effect loop for the use of external
units such as box or rack effects. When
connecting effects to the loop, the internal
line is bypassed and all signal passes
through the external unit and back to the
EBS Fafner.
VOLUME - Utgångsvolymen VOLUME
kontrollerar all volym genom förstärkaren
fram till slutsteget samt linje utgången.
STANDBY - STANDBY omkopplaren på
frontpanelen stänger av alla utgångar;
linjeutgången, effect send, balanserade
utgången och högtalarutgångarna, förutom
TUNER OUT som alltid är aktiv.
BALANCED OUTPUT - Är en
linjeutgång av mycket hög kvalitet. Denna
utgång innehåller en elektroniskt flytande
balansering som vid osymmetrisk
mottagning i t.ex. en obalanserad ingång,
är självjusterande för att alltid ge en perfekt
signalöverföring.
Den balanserade utgången fungerar som
en linebox och kan anslutas till t.ex. PA-
mixers eller studioinspelnings-utrustning.
Jordlyft är till stor hjälp när jordbrum
uppstår. Tryck in Gnd Lift omkopplaren för
att koppla bort jorden.
Post Eq omkopplaren väljer vilken signal
som skall sändas. I det inre läget tappas
hela ljudbilden av, inklusive effekter,
medan det yttre läget väljer det ofärgade
ljudet direkt från ingången, med samma
signalstyrka som instrumentet.
EFFECT LOOP - EBS Fafner har även
en effektloop för inkoppling av externa
effekter i box eller rackformat. När loopen
kopplas till effekter bryts den interna
kopplingen och allt ljud passerar igenom
dessa och tillbaks till förstärkaren.
7. Vrid upp VOLUME ratten till lämplig
ljudnivå - en början till ditt eget
drömljud.
BYGGA UPP ETT LJUD...
(%6 )DIQHU
LQQHKnOOHU HQ P\
FNHW VRILVWLNHUDG OMXGEHDU
EHWQLQJVGHO VRP HUEMXGHU GLJ
PlQJGHU DY DQYlQGEDUD EDV OMXG
8. Ställ BYPASS omkopplaren i uttryckt
läge. Detta tillåter oss att bearbeta lju-
det.
9. Spela på din bas. Notera att det inte är
någon skillnad i ljudet än.
10.Filterrattarna som är markerade med +
och - tecken kan antingen förstärka
eller dämpa det aktuella frekvens-
området.
Dessutom har MIDDLE ytterligare en
ratt för frekvensval som ger dig total
kontroll över mellanregistrets klang och
karaktär.
11.Ändra filter-inställningarna och mellan-
registrets frekvenskontroll. Lägg märke
till alla skillnader i ljudet. Jämför det
"raka" med det filtrerade ljudet genom
att koppla om filteromkopplaren till
BYPASS läget.
12.Prova enligt ovan med att använda
preshape filtren märkta HI och LO. No-
tera att dessa filter inte påverkas av
BYPASS omkopplaren.
7. Move over to the VOLUME knob and
adjust for the desired output volume.
BUILDING THE SOUND...
<RXU
(%6 )DIQHU
IHDWXUHV DQ
HQKDQFHG WRQH VKDSLQJ FLUFXLW WKDW
ZLOO HQDEOH \RX WR FUHDWH D YDULHW\ RI
EDVV VRXQGV
8. Toggle the BYPASS switch to it’s outer
position to enable sound shaping.
9. Play your bass. Note that there isn't any
difference in the sound yet.
10.The filters are basically of the boost/cut
design. This means that the level
controls marked with + and - signs,
either boost or cuts the selected fre-
quency band. Further, the MIDDLE
section facilitates a frequency control
for precise adjustment of the midrange.
11.Gradually increase or decrease the level
and vary the frequency, where is, of the
various filter sections. Notice how the
sound is effected. An A/B comparison
can be made by switching the filter
switch to BYPASS.
12. Repeat as above by trying out the two
preshape filters LO and HI. Note that
these controls are not effected by the
BYPASS switch.