Falconeyes TE-300D User manual

Thank you for purchasing FalconEyes’ products.
For further details of our related products, please contact your
local distributor or visit our webpage at www.falconeyes.com.hk
Thank you.
Please read this manual carefully before using this product.
Falcon Eyes Limited
3
FM1012_TE-D_eng
D) Specification
Instruction Manual
TE-300D / TE-400D / TE-500D
TE-600D / TE-900D / TE-1200D
Power Range
Modeling
Power Control
Guide No.(ISO100/m)
Recycle Time
Flash Duration(t: 0.5s)
Angle of Illumination
Color Temperature
Operating Voltage
AC 110-120 60Hz/AC 220-240 50Hz
Triggering
Accessories Included Reflector,Power Cord, Sync Cord, Modeling Lamp
Optional Accessories Softbox, Barndoor ,honeycomb , Color Filter Set, Snoot, Light Stand, Umbrella etc.
Model No.
TE-D Series Studio Flash
400Ws300Ws 500Ws 600Ws 900Ws 1200Ws
TE-300D TE-400D TE-500D TE-600D TE-900D TE-1200D
150W 150W 150W 250W 250W 250W
5300K - 5500K
≥55°
1/400-1/1100
1/32~1, (LED step 1.0-6.0)
55 64 70 78 90 100
0.5~1.5s 1~2s 1~2.5s 1~3s 1~3.5s 1~4s
E) Attentions
Since there could be high voltage inside the unit, please DO NOT open
or repair the unit yourself. If there is any defect, please contact the
experienced technician.
Avoid strong light directing to the photo sensor.
For better maintenance, if the unit has been triggered continuously 10
times in a short period please leave the unit dormant 2 minutes.
Please ensure the power is switched off after use.
Photo Sensor, Sync Cord, Test Button

B) Panel Diagram
A) Features C) Instructions
1 2
This is a stable and quick rechargeable studio flash system. Its power is
variable from 1/32 to 1. Its capacitor can discharge automatically when it
is not in use. The brightness of the modeling lamp is directly proportional
to that of the flash tube, so that you can preview the lighting effect before
taking the pictures. Besides, it contains a perfect notification design for
fully-charged and over-heat condition. When it is fully charged, it will buzz
and the indicator will be on as green. TE-D series signifies the most
durable, user-friendly and professional oriented.
i) Connect to the power supply. Turn on the lighting unit and the
modeling lamp. Then, the brightness of the flash tube and the modeling
lamp is adjustable and their lighting effect is directly proportional to
each other. If there is no need to control the brightness, you can just
turn on the flash. When the buzzer stops buzzing which means the
capacitor is fully charged, the flash can then be controlled to spark.
ii) From now on, the illuminating angle of the flash unit can be
adjusted. The result of shooting can be previewed by using the
modeling lamps.
iii) The guide number is directly proportional to the brightness of
the flash. The stepless power control can be adjusted from 1/32 to full
power for different luminosity of flash and modeling lamp.
iv) This flash unit is thermo sensitive. When the temperature is
higher than the safety standard (indicator light will be lighted by green),
the flash will be shut down. Once it is cooled down, the flash will
function again. Its purpose is to prevent the overheat.
v) There is a sync cord included in the package, which one end is
connected to the flash unit and the other end is connected to the
camera.
vi) There is a switch to turn the buzzing function on. When it is on,
it will buzz until the capacitor is fully recharged.
vii) The reflector cap is changeable. To change it, please press a
button down which is on the peripheral of the housing and turn the
reflector anticlockwise. Then, it can be removed.
viii) If the umbrella reflector is used, please insert the stem into the
umbrella installation hole which is at the bottom of the flash housing.
Then, tighten the screw of the knob.
Beeper On/Off Switch
Modeling Lamp
Mode Switch
Modeling Lamp
ON/OFF Switch
Test Button
Main Power
On/Off Switch
Sync Socket
LED Display
Ready Lamp
Fuse
Power Socket
Power Control Dial
Remote On/Off Switch
Photo Sensor