FAMITEC AQ3 User manual

Wet and Dry Vacuum Cleaner
User Manual v1.0

–
In order to avoid accidental injuries such as electric shock and fire caused by improper use, please read
all instructions carefully before use and save this instruction properly for future use. This product can
only be used indoors, and it is prohibited to install and use this product outdoors, in bathrooms, and
around swimming pools.
 The appliance can be intended for use by persons (including children aged 8 years and above) with
reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they have
been given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved.
 This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
 Do not allow children to treat or use the appliance as a toy.
 Children should be supervised to ensure that they do not play with the appliance.
 Children shall not play with the appliance, cleaning and user maintenance shall not be made by
children without supervision.
 The appliance is only to be used with the power supply unit provided with the appliance.
 This appliance contains battery that is non user-replaceable and only replaceable by skilled persons.
 For the purpose of recharging the battery, only use the detachable power supply unit provided with
the appliance.
 Make sure the appliance is turned off before replacing the roller brush, cleaning and maintaining the
appliance.
 Do not touch the plug or any live part of the appliance with wet hands to avoid the risk of electric
shock.
 If the charging power cord is broken and damaged, please call the professional maintenance
personnel to replace it to avoid hazards.
 Keep the ventilation and moving parts of the appliance away from long hair, loose clothing, fingers,
and other parts of the body.
 During use, if you find leakage or the motor temperature is too high and abnormal sounds, such as
overheating, abnormal sounds, odor, sudden drop in suction, etc., you should stop using it and
contact us for warranty services.
 If you do not use the appliance for a long time, put the appliance on the base station and keep it
charged.
 After use, clean the dirty water tank in time and keep the ventilation path unobstructed so as to
avoid blockage, which will cause the suction to drop or the motor to heat up, which will affect the
service life of the appliance.
 After use, store the appliance in a dry place. A damp place will affect the insulation and service life
of the appliance.
 Check the opening of the nozzle regularly. If there is any blockage, please remove it in time to avoid
the decrease in suction caused by the blockage and affect the performance of the appliance.
 The main unit of the appliance and base station cannot be soaked in water or rinsed.
SAFETY INSTRUCTIONS AND PRECAUTIONS
 When the appliance fails, do not attempt to repair it by yourself. Call our company for warranty
services.
 Do not shake the appliance up and down or collide violently, and do not tilt the appliance to one
side or lay it flat to prevent sewage from flowing into the main unit.
 Do not use the appliance to vacuum the laser printer or toner used inside the copier, as these objects
may cause a fire or explosion.
 Do not use the appliance to clean flammable or explosive liquids such as gasoline. Do not use toxic
solutions such as chlorine bleach, ammonia, sewer cleaners, or other liquids.
 These instructions are also available in our website www.famitec.com
1. Do not use the detergent that contain acid, toxic, alkali solutions, foaming substances, or substances
harmful to the appliance and environment. Read the ingredients and user instructions of the
detergent before use. If a large amount of detergent is added, more foam will be generated during
use, which may leak into the motor and cause danger.
2. Do not apply any scented products to the filter of the appliance. The chemicals in such products are
known to be flammable and cause the appliance to catch fire.
3. The base station of the appliance can only be used on this appliance to avoid damage or any danger
caused by using it on other products.
4. To avoid clogging of the filter, it is recommended to clean the filter regularly and to replace the filter
every 3-6 months.
5. All technical and other data reflected in manual were obtained by our company or a designated
third-party testing company, and our company owns the final interpretation rights.
6. The performance of the appliance in the actual living environment may vary due to changes in
environmental conditions.
 Do not use the appliance to clean smoking or burning objects such as charcoal, cigarette butts, or
matches.
 Do not use the appliance to clean sharp or hard objects, such as nails, glass, screws, or coins, or it
will cause damage to the scrubber.
 Do not use the appliance to clean shoe polish, paint, pigment, and other stains with strong grease,
strong stickiness, or strong staining.
 Do not disassemble the appliance by yourself. There are no customer serviceable parts in this
machine, and do not attempt to change the performance of the appliance, otherwise it will cause
danger.
 Do not get the appliance wet, otherwise it may cause fire and electric shock due to a short circuit in
the appliance.
P
RECAUTIONS
–––
WARNINGS

1. Product Description
1.1 Inside the Box 01
1.2 Parts Description 02
1.2.1 Wet and Dry Vacuum Cleaner 02
1.2.2 Charging and Cleaning Base Station 03
1.2.3 Clean and Dirty Water Tank 03
2. Use of Product
2.1 Operation Precautions 04
2.2 First Time Installation 05
2.3 First Time Battery Charging 06
2.4 User Interface 07-08
2.5 Operation 08-10
2.6 Removing and Filling of Clean Water Tank 11
2.7 Removing and Cleaning Dirty Water Tank 11
3. Cleaning and Maintenance
3.1 Cleaning of Dirty Water Tank 12
3.2 Cleaning of Dirty Water Tank Filter 12
3.3 Deep Cleaning of Dirty Water Tank 13
3.4 Cleaning of Clean Water Tank Filter 14
3.5 Deep Cleaning of Clean Water Tank 14
3.6 Cleaning of Vacuum Cleaner 15
3.7 Cleaning of Roller Brush and Roller Brush Cover 15
4. Specifications 16
5. FAQ and Trouble Shooting 17
6. Warranty Services 18
TABLE OF CONTENTS
–––
1
1.1 Inside the Box
PRODUCT DESCRIPTION

2
1.2 Parts Description
PRODUCT DESCRIPTION
3
PRODUCT DESCRIPTION

4
2.1 Operation Precautions
 When the main unit is stand upward, it will automatically shut down if there is no operation within
20 seconds.
 When the appliance is operation, do not lift or move the main unit up or down.
 Do not recline the main unit to one side or lay the main unit flat to prevent sewage from flowing
back into the motor and causing damage.
 Do not recline the main unit more than 155° to protect against water leakage.
 Do not use the appliance to clean the foamy liquids or corrosive liquids.
 Do not put the toxic & corrosive detergent to clean water tank for Vacuum and Wash (Auto or Turbo
mode).
 Place the main unit to base station after the operation. Empty the dirty water tank and fill the water
in the clean water tank to the recommend "Water Level" line before starting of self-clean process.
 Charge the battery of appliance and ensure the minimum battery level (1 green LED light of battery
indicator is lighted up) is achieved before press the " " button to start the self-clean process.
 After the self-clean process is completed, pour out the sewage from the dirty water tank and clean
the dirty water tank with detergent and cleaning brush. Empty the clean water tank also.
USE
OF PRODUCT
5
2.2 First Time Installation
Install the base station
Place the base station against the wall and connect the power cord.
Install the main unit
Insert the handle into the fixed slot of the appliance in the vertical direction. A "click" sound indicates
that the installation is successful. Check that the handle is installed stably without loosening.
Align the Roller brush cover with the clips and install it on the brush head.
USE OF PRODUCT
Note: Do not place the base station
near heat sources or damp areas such
as radiators, kitchens, or bathrooms

6
2.3 First Time Battery Charging
After the base station is powered on, place the main unit correctly on the base station, and the main
unit will automatically charge immediately. The Battery charging indictor is lighted up and flashes, and
it is fully charged once 3 green LED lights are all lighted up.
USE OF PRODUCT
Note
:
 Before using it for the first time,
please put the appliance on the
base station and charge it for
more than 3 hours or until the 3
green LED lights of battery
indicator are all lighted up.
 After the appliance is fully
charged, and no further action in
five minutes, the display and the
appliance will turn off.
 Make sure the surroundings are
unobstructed and away from fire
and water sources.
7
2.4 User Interface
Icon Function / Indication
Vacuum mode is helpful in vacuum of dusts, hairs, shredded paper on hard floor,
rugs and mats before “vacuum & wish” since some hairs and papers were struck on
the floor after they are wet.
Auto mode is vacuum & wash at the same with normal suction power for hard floor.
Turbo mode is vacuum & wash at the same
time with maximum suction power
for
hard floor.
Self clean mode is automatic cleaning process of roller brush.
Front Tank alert is flashing when the dirty water tank is full or removed in operation.
Rear Tank alert is flashing when the clean water tank is empty or removed in
operation.
Sidebar LED is
lighted up from left to right when power on the main unit. And the
LED is off from right to left when switch off the main unit.
Tilt indicator indicates the pulse status, and recline the main unit to keep on the
operation. If there is no action in 20
seconds, then the appliance will automatically
shut down.
USE OF PRODUCT

8
Icon Function / Indication
3 green LED lights lighted up = Full
2 green LED lights lighted up = ~ 67%
1 green LED light lighted up = ~ 33 %
1 red LED light lighted up = ~ 20% (place the main unit to base station for
battery charging)
1 red LED light flashing = Low Battery. The appliance will switch off soon
2.5 Operation
Power key (Long press time is one second, short press time is instant)
Function key (Short press to switch modes, Vacuum - Auto – Turbo)
Power On:
Pick up the main unit from the base station, and the brush does not
work in a standing state. You are required to recline main unit, and
long press the " " button to power on the appliance. It enters the
vacuum mode and starts to work. Short press the " " key to switch
between three modes (Vacuum, Auto, and Turbo) cyclically.
Pause:
After short pressing the " " key or tilting the handle forward to the
standing position, the main unit will temporary stop working. If
you recline the main unit, it will resume working automatically. It will
be automatically shut down if there is no operation within 20 seconds
in the standing state.
Shutdown:
Long press the " " key to shut down.
USE OF PRODUCT
9
Auto & Turbo mode operation
If there is no water or the water level is very low in the clean water tank when it starts the operation, it
takes 5 seconds to detect the clean water level and then the Rear tank alert is flashing. After you refill
the water and re-install the clean water tank in place, short press the “ ” button and the operation
will continue.
If the sewage level is full and exceed the “Water Level” line in the dirty water tank in the operation, the
Front tank alert is flashing. The operation is continued after the dirty water tank is empty and re-install
in place.
One-button self-clean (Duration: ~27 minutes)
USE OF PRODUCT
Note: self-clean process can only be started when the minimum battery capacity is 1 green
LED light of Battery indicator is lighted up

10
When the main unit is on the base station, short press the
" " button on the handle, the self-clean mode indicator
is light up, the main unit will enter the self-clean process
and start cleaning the roller brush. After cleaning the roller
brush, it will automatically start the air-drying process.
Self-clean process: spray water first, and then the roller
brush will rotate and stopping intermittently for self-clean.
After this cycle operation, it will perform a rapid water-
throwing operation and finally enter the air-drying state.
Lastly, the roller brush will run slowly until the self-clean
process is completed.
During the self-clean process, short press the " "
button. The self-clean will stop immediately. If you short
press " " button again, the main unit will re-start the
self-clean process from the beginning.
After the self-clean process is completed, the appliance
will automatically shut down within 5 minutes after the
battery is fully charged and without any operation.
USE OF PRODUCT
Note :
1. Pour out the sewage from the dirty water tank and fill the water in the clean water tank
before staring the self-clean process.
2. If the dirty water tank is full and front tank alert is flashing in the process, pour out the
sewage from dirty water tank and ensure that the tank is empty and re-
installed properly.
The self-clean process will continue.
3. If the clean water tank is empty or Rear tank is flashing in the process, refill the water to
clean water tank and ensure that the tank is not exceed the recommend “water level” line,
and also ensure that the tank is re-installed properly. Short press " " button again,
the self-clean process will continue.
11
\
2.6 Removing and Filling of Clean Water Tank
Disassembly:
Hold the main unit with one hand, press the release button
of the clean water tank with the thumb of the other hand,
and take out the clean water tank.
Filling water (or adding detergent if request):
Flip open the top cover of the clean water tank and pour in
water. For deep cleaning purposes, pour an appropriate
amount of detergent into the water tank to dilute it, and
shake it evenly before use
Installation:
Hold the main unit with one hand and hold the upper sides
of the clean water tank with the other hand. Align the
bottom of the clean water tank with the support position of
the main unit and push inwards. After you hear a "click",
the installation is successful.
2.7 Removing and Empty Dirty Water Tank
Disassembly:
Hold the main unit with one hand and press the dirty water
tank release key with the other hand while pulling out the
water tank outwards.
Take out the filter and top cover in an upwards direction
pour out the sewage.
Installation:
Reinstall the upper cover of the dirty water tank first, and
then install the filter.
Hold the main unit with one hand and hold the dirty water
tank with the other hand. Align the bottom of the dirty water
tank with the support position of the main unit and push
inwards. After you hear a "click", the installation is
successful.
USE OF PRODUCT

12
3.1 Cleaning of Dirty Water Tank
Simple cleaning:
When the water level of the dirty water tank exceeds the
‘Water Level’ line, Front Tank alert is flashing, take out the
dirty water tank (refer to point 2.7). Pour out the garbage in
the wet and dry separator and pour out the sewage in the
dirty water tank, and then rinse the dirty water tank with
clean water.
3.2 Cleaning of Dirty Water Tank Filter
Remove the filter:
Hold the filter removal keys on both sides and lift the filter
up.
Use detergent to clean, rinse with clean water, and dry it in
an open area. Install the filter back in place after cleaning. A
soft-bristled cleaning brush can be used to assist in cleaning.
.
CLEANING AND MAINTENANCE
Note: pour sewage and wet waste into the sink with
the anti-clogging filter plug to prevent the sewer from
clogging.
Note
: Do not use a stiff or wire brush to clean the filter.
Note: After the filter has been used for a period of
time, it needs to be disassembled and replaced
according to the usage conditions. It can be cleaned
regularly, dried in an open area, and reuse. It is
recommended to replace the filter with a new one
every 3-6 months.
13
3.3 Deep Cleaning of Dirty Water Tank
Use tap water to rinse the dirty water tank and the wet and dry
separator on the top cover until it is clean. You can use the detergent
and cleaning brush to clean the dirty water tank, the wet and dry
separator, and the dirt level sensor.
CLEANING AND MAINTENANCE
Note
: If you find that the suction nozzle of the brush head is blocked or dirty, clean it up
in time. If the dirty water tank is not cleaned thoroughly, the Front tank alert will flash, even
if the dirty water tank is empty.
Note
:
C
lean the dirt level se
nsor
a
lso, the Front tank alert will flash even though the dirty
water tank is empty

14
3.4 Cleaning of Clean Water Tank Filter
3.5 Deep Cleaning of Clean Water Tank
Add the water and detergent, cover the lid and shake the clean water tank. During the cleaning process,
you can use a cleaning brush to assist in cleaning. After cleaning, rinse the clean water tank with clean
water.
CLEANING AND MAINTENANCE
Note: After using the water filter for a period of time, it needs to be disassembled and
replaced according to the usage conditions. It can be cleaned regularly, dried in an open
area, and reuse. It is recommended to replace the new water filter every 3-6 months.
15
3.6 Cleaning of appliance
Before or after using the appliance, please make sure that the appliance is turned off, and then use a
dry cloth or paper towel to clean the dust adhering to the body.
3.7 Cleaning of Roller Brush and Roller Brush Cover
Lift up the roller brush cover, take out the roller brush for cleaning. Use a dry cloth or paper towel to
clean foreign objects.
CLEANING AND MAINTENANCE
Warning
Do not rinse the main
unit directly with water
at the faucet.
Warning
: Do not rinse the brush heads with water directly at the faucet.

16
Product Name AQ3 Wet & Dry Vacuum Cleaner
Main Unit Dimension 260 x 260 x 1090mm
Main Unit Weight ~3.8Kgs
Base Station Dimension 309 x 283 x 232mm
Base Station Weight ~1.2Kgs
Charging Time 3.5 +/- 0.5 hours
Model no. 32-203-XX (XX stands for different version)
Power Supply unit Input 100-240V ~, 50/60Hz, 0.8A
Power Supply unit Output 26.5V, 1.2A, 31.8W
Dirty Water Tank Capacity 600ml
Clean Water Tank Capacity 650ml
Battery Capacity 2,400mAh
SPECIFICATIONS
17
Problems Possible cause Solutions
The Appliance
is not
working
Running out of battery
Charging after use and ensure that the
appliance is full charged before use
Overheat
protection of battery
circuit.
Wait for the battery temperature to return
to normal and try again.
The
sewage in the dirty water tank
exceeds the “Water Level” line.
Clean the dirty water tank and s
crub the dirt
level sensor at the upper cover of the
dirty
water tank. Install
the tank back on and try
again.
Dirty water
tank or roller brush not
in place.
I
nstall the dirty water tank and roller brush
properly.
Clean water tank is out of water. Fill water into clean water tank.
Clogged roller brush or dirty water
tank pipes. Clean the roller brush and pipe.
Roller brush stuck. Clean the roller brush.
Unable to charge
The base station not powered. C
heck the contact of electric socket and
power supply unit.
Bad contact of battery
charging
pins. Clean the surface of contact pin.
Damaged power cord. Contact manufacturer for warranty service.
The main unit was not installed
in
place at the base station.
Make sure the main unit
is in place by press
it lightly.
Unable to start self-
clean process
Dirty water tank full.
Pour sewage out of dirty water tank and
install back properly.
Dirty water tank not installed. Ensure
the dirty water tank is installed in
place.
Low or depleted battery. charging and ens
ure the minimum battery
level is achieved.
Clean water tank is out of water.
Fill water
(not exceed the “water Level”
line) into clean water tank
and installed
back properly. Short press “
” to continue
the self clean process.
Abnormal sound
from running motor
The roller brush is stuck, or the
sewage flows back into the motor.
Correctly install the roller brush and clean
the roller brush. Operating the appliance
correctly to prevent sewage from flowing
back into the main unit.
Suction power
decrease
The dirty water tank suction pipe
is clogged, or the filter is dirty.
Clean the dirty water pipes, dirty water
tank and the filter.
FAQ AND TROUBLE SHOOTING

18
Famitec provide the product warranty services to the original purchaser of this product that this product
will be free from defects in material and workmanship under normal use and service for 12 months from
date of purchase. We will, at its option, repair or replace with a new or refurbished product. We reserve
the right, before having any obligation under this limited warranty, to inspect the product, and all costs
of shipping the product for inspection and warranty service shall be borne solely by the purchaser.
For the fastest processing of a warranty claim, the Purchaser should e-mail [e-mail] and
include the product name and model #, proof of original purchase, complete contact information, and
detailed information about the issue, including pictures when applicable.
The limited warranty is valid only in accordance with the following conditions:
1. The product is purchased directly from Famitec, or an authorized reseller, or distributor.
2. Only the original purchaser is covered by this warranty. This warranty is not transferable.
3. Product is for personal use only. This warranty is void if the product is used in a commercial or
institutional establishment.
4. This warranty does not cover normal wear and tear, or damage caused by misuse, abuse,
negligence, accident, acts of nature, or unauthorized modification or repair.
5. Purchaser must present acceptable proof of purchase for the product.
Disposal
When this device has reached the end of its life, please dispose of the device properly. This
and other electrical appliance contain valuable materials that can be used recycled. Electronic
waste may be harmful to our environment if not disposed of properly.
We ask that you follow your governing agency’s rules and regulations when disposing of electronic
appliances. Pleased find an authorized recycling facility near you.
Contact
If you have any questions or concerns about operation or warranty of this product, please contact our
customer service by email [e-mail]
2022 Famitec Ltd. All rights reserved.
WARRANTY SERVICES
makes your life easier