Fantasea BigEye Lens FXF80 User manual

1

2
1. Introduction
The Fantasea BigEye Lens FXF80/100/200 is a patented “wet” accessory wide
angle lens that was specially designed for the FujiFilm WP-FXF80, WP-FXF100
and WP-FXF200 underwater camera housings. The lens fits onto the housing
lens port and can be installed and removed during the course of the dive. It is
perfect for photographing seascapes, divers, ship wrecks and schools of fish
without moving further away from the subject, thereby still taking full
advantage of water clarity and artificial light sources.
2. Technology
The BigEye Lens FXF80/100/200 makes use of a new patented lens
technology, which allows for high quality underwater wide angle images free
of distortions. The new technology uses air instead of glass as an optical
element and enables recovering 100% of the camera lens optical properties
that would normally be lost underwater. The air pocket inside the lens
enhances the angle of light refraction, thereby restoring the original angle of
coverage of the camera lens (see figures below). This patented technology
was specially designed for underwater photography and therefore the lens
should only be used when the system is submerged in water.

3
3. Included in Box
BigEye Lens FXF80/100/200
Neoprene Lens Cover
Secure Line
Warranty
Instruction Manual
4. Specifications
For the FujiFilm WP-FXF80, WP-FXF100 and WP-FXF200 housings
Depth rated to 60 meters / 200 feet
Field of view recovery (magnification): 105% (x 0.7)
Angle of coverage: 80 degrees
Lens material: Optical glass, hard coated plastic and anodized
aluminum
Weight: 492g
Dimensions: 157x67mm
: 5. Instructions for Use
A. Please use the utmost care and do not use excessive force when
assembling and disassembling the lens, in order to not cause any damage
to the product.
B. Attach the secure line to the lens and the housing, in order to secure the
lens to the housing.
C. During the dive, install the BigEye Lens by attaching it to the housing lens
port, as shown on the figure on the following page.
Important Notice:
Prior to installing the lens, make sure you are holding the lens according to the shape of
the lens port, so the gap designed on the lens adaptor corresponds with the housing
built-in flash diffuser. To install the lens, push it against the lens port starting from the
bottom right corner (when facing the housing) and proceeding towards the top left
corner, where the housing built-in flash diffuser is located. After lens installation, make
sure it is properly attached by gently trying to pull it out. If properly installed, the lens
should not easily come off the lens port.

4
D. Please note that the BigEye Lens was designed to work underwater
only. Therefore, the lens should only be installed underwater, while
letting water enter the gap between the macro lens and the housing’s
lens port. Make sure that there are no air bubbles trapped between the
BigEye Lens and the housing lens port before taking images.
E. During the beginning of your dive, your lens might become foggy as a
result of an increase in the air temperature inside the lens, following
submersion in cooler water. Storing the lens in a cool dry place when not
being used, such as a padded housing bag with a few silica gel packs
inside, and submerging it in cool water for 10 minutes prior to the dive,
will assist in preventing such condensation. However, even if your BigEye
Lens starts fogging up at the beginning of the dive due to temperature
differences, please note that continuing to dive with it for about 10
minutes will eventually dissolve the fog.
F. When taking photos with the BigEye Lens installed, set your camera
focus mode to “Macro”. Failing to do so will result in blurred images.
Built-in Flash Diffuser

5
G. The BigEye Lens can be removed and installed repeatedly throughout the
course of the dive. Whenever removing the lens, set your camera focus to
the desired mode, if it is not “Macro”.
H. In order to remove the BigEye Lens from the housing lens port, first
detach the secure line and then gently push it off, starting from the
secure line loop on the right side of it, using your thumb in an outward
direction as shown on the image below.
I. When removing the BigEye Lens from the housing, it can be secured by
attaching it to the corresponding EyeGrabber lens holder, which mounts
on Fantasea Flex Arms, thereby making it easily available for future use.
For further information, please visit our website at
www.fantasea.com\FantaseaEyes
J. It is recommended to use an external strobe when the BigEye Lens is
mounted on the housing. The BigEye Lens blocks the camera internal
flash, resulting in underexposed or shaded images.

6
K. When using an external flash, there are a few techniques that should be
followed in order to avoid a lens flare, which is often encountered when
using dome ports of any kind due to the reflection of the sub or strobe:
a. Make sure that the wings of the BigEye Lens are positioned at an
angle that blocks the strobe output, as well as the sun. In order to
prevent the wings from unintentionally changing position, some
friction has been added, but rotating them can be easily done by
following a simple technique. In order to rotate the wings, simply
hold them and push them against the housing when the BigEye
Lens is mounted on your housing lens port. At the same time,
rotate them around the lens, till they have reached the desired
position. Images in which the sun is captured can be usually taken
during mornings or afternoons, when the sun is not as strong as
during the middle of the day. In general, the sun will have a much
softer and successful effect during early and late hours of the day
and will also cause less of a flare.
b. Make sure that the strobe is not positioned towards the lens.
When shooting a nearby subject, for instance, it is better to
position the strobe a little bit in front of the camera housing
rather than behind it (so the light doesn't reflect on the BigEye
Lens), or if you choose to position the strobe behind the camera
housing, make sure it's not pointed directly towards the lens, but
a little bit tilted towards the side.

7
6. Care & Maintenance
A. Please use the utmost care and do not use excessive force when
assembling and disassembling the different accessories, in order not
cause any damage to the product.
B. Keep the BigEye Lens away from extreme high temperatures, as under
direct sunlight, since it might damage the O-ring and interfere with the
watertight seal of the lens.
C. Do not clean the lens with any chemical solvents or other materials,
which might cause damage to the plastic dome.
D. Never look at the sun through the lens.
E. When storing the lens and during transportation, make sure that it is
properly protected in order to prevent scratches, cracks or any other
damage to the lens.
F. After Dive Care:
I. Detach the BigEye Lens from the housing lens port and rinse all
lens components in fresh water.
II.To ensure that the accumulated salt has completely dissolved, it is
recommended to soak the lens in warm fresh water once in a
while.
III.Wipe the water drops with a soft cloth. Do not leave any droplets
to dry on lens surface, as permanent water spots may remain.
IV.Store the lens in a dry and protected area. Storing the lens in a low
humidity environment will decrease the chances of the lens
fogging up when submerged in water.
V. Do not store the lens in presence of chemicals, solvents or fuels.

8
C
Co om mp pl le et te e C Co om mp pa ac ct t D Di ig gi it ta al l H Ho ou us si in ng g A Ac cc ce es ss so or ry y S Sy ys st te em m
For further information, please contact us at www.fantasea.com/contact
or visit our website www.fantasea.com