Farm King 1266 Product manual

Conventional Auger
Model 1266, 1272, 1276 & 1282
OPERATOR AND PARTS MANUAL
052011 SZ000189

3
Table of Contents - 1266, 1272, 1276 & 1282 Conventional Auger
Introduction .................................................................................................................................4
Safety............................................................................................................................................5
• Safety ................................................................................................................................5
• General Safety..................................................................................................................5
• Operation Safety ..............................................................................................................5
• Transport Safety...............................................................................................................6
• Electrical Safety................................................................................................................6
• Safe Operation Instructions ............................................................................................7
Assembly......................................................................................................................................8
• 6 Bolt Hub Assembly .....................................................................................................10
• Stop Flag andTrack Stop ...............................................................................................10
• Head Drive Assembly ....................................................................................................10
• Assembly Instructions ................................................................................................... 11
• Assembly Instructions - PTO 540 RPM Drive...............................................................13
• Assembly Instructions - PTO 1000 RPM Drive.............................................................14
• Assembly Instructions - Electric Drive .........................................................................15
Parts............................................................................................................................................16
• 1266, 1272, 1276 and 1282 Parts ...................................................................................16
• Decals..............................................................................................................................21
• PTO 540 RPM Drive........................................................................................................22
• PTO 1000 RPM Drive......................................................................................................23
• 540 Gear Box..................................................................................................................24
• 1000 Gear Box................................................................................................................26
Warranty ....................................................................................................................................28
Manufacturer’s statement: for technical reasons Buhler Trading Inc. reserves the right to modify
machinery design and specifications provided herein without any preliminary notice.
Information provided herein is of descriptive nature. Performance quality may depend on grain
type, grain moisture, auger elevation and other factors.
Table of Contents

4
Introduction - 1266, 1272, 1276 & 1282 Conventional Auger
Introduction
To the owner
Thank you for purchasing a Farm King 1266, 1272, 1276 or 1282 Conventional Auger.
Farm King Conventional Augers have been designed to provide many years of profitable and
dependable service. To assure maximum performance of your auger, it is mandatory that you
thoroughly study the operator’s manual and follow its recommendations. PLEASE EXAMINE
YOUR UNIT CLOSELY AND READ THE ASSEMBLY INSTRUCTIONS TO SEE THAT YOUR UNIT IS
PROPERLY ASSEMBLED. Proper operation and maintenance are essential for safety, to maintain
performance, and to maximize the life of the auger. When ordering parts or inquiring about the
auger, you must include the serial number which is located on the second upright of the lower
truss support.
It is the owner’s responsibility to:
Operate and maintain this auger in a safe manner and in accordance with all applicable local, state,
and federal codes and/or laws.
Make sure each and every operator has read the operator’s manual and thoroughly understands
safe and correct operating procedures.
Make sure unauthorized people do not operate or are not in the vicinity of the auger while it is in
operation.
Maintain the auger in accordance with the maintenance schedule in this manual. Furthermore, as
additional technology becomes available, the owner is responsible for improving the safety and
reliability of the system.
Fulfill all warranty obligations so as not to void the warranties. Verify the unit is warranty registered
prior to making any warranty claims.The warranty section at the back of this manual outlines the
warranty policy of Farm King.
Abuse or modifications to the auger that change the performance other than original factory
specifications void the warranty.
Farm King reserves the right to make product improvements to the equipment at any time. It shall
not be obligated to make such changes to machines already in service.
*The owner, manager and/or operator is responsible for safe, accurate operation and maintenance
of the Farm King 1266, 1272, 1276 or 1282 Conventional Auger.

5
Safety - 1266, 1272, 1276 & 1282 Conventional Auger
Safety
Safety Instructions
An Operator‘s Manual is furnished with each grain auger. Additional or replacement manuals
are available. Do not operate the unit before reading and understanding the Operator‘s Manual.
Understand the operating procedures below to avoid personal injury or death.
The alert symbol is used throughout this manual. It indicates attention is required and identifies
hazards. Follow the recommended precautions.
The safety alert symbol means…
ATTENTION! BECOME ALERT!YOUR SAFETY IS INVOLVED!
General Safety
An auger can collapse and fall on the operator or bystander causing serious injury or death.
Always support the discharge end when the following conditions occur:
• While unit is in operation.
• When dismounting the undercarriage.
The accidental tipping or upending of an auger may cause serious injury or death to the operator
or bystanders. When the grain flow is shut off to the auger an overbalance situation can occur,
suddenly raising the intake auger. Adequate anchorage of the intake end or support from bin is
required at all times, especially in the following conditions:
• While unit is in operation.
• When moving the auger.
• When raising or lowering the auger.
• Maximum elevation is determined by interference between track car and auger structure.The
operator must stop raising the auger before track car reaches the end of the track. Continued
lift will cause failure of the winch, lift cable or auger supports, causing auger to collapse,
which can result in serious injury or death.
Contact with rotating flighting will cause serious injury or death.
• Do not stand on the intake cage.
• Keep hands, feet and clothing away from the intake and discharge flighting.
Operation Safety
Intentional or accidental contact with moving parts may result in a serious injury or death. Observe
the following operating procedures.
• Keep all safety devices in place.
• Do not adjust, service, lubricate, clean, unclog or move the mechanism until all power is
shut off.
• Keep hands, feet and clothing away from moving parts while in operation.
• Keep off the equipment at all times.
• Make certain that everyone is clear of the equipment at all times.
• Make certain that everyone is clear of the equipment before applying power.
• Keep children, visitors and all untrained personnel away from machine while in operation.

6
Safety - 1266, 1272, 1276 & 1282 Conventional Auger
Transport Safety
Care must be used when moving or transporting the auger. Accidental tipping or upending of an
auger can occur and may cause serious injury or death to the operator or bystanders.
• Never move the auger manually.
• Be sure auger is empty before attempting to move.
• Never push on the undercarriage of the auger.
• Tow the auger at slow speed and in the down position.
• Always test the intake end of the auger for downward weight when attaching or releasing.
• Never raise the hitchpoint higher than the vehicle‘s tow bar.
Electrical Safety
Contact with overhead wires may cause electrocution of the operator or bystanders. Contact with
overhead obstructions may cause collapse or tipping of the auger or may cause the overhead
obstruction to fall. In both cases the operator or bystander can be seriously injured or killed.
Observe the following:
• Tow the auger at slow speed and in the down position.
• Raise or lower the auger slowly.
Electrical malfunction can cause electrocution of the operator or bystanders.
Observe the following rules.
• Disconnect power and electrical driven units before resetting motor overloads.
• Do not operate electric motor equipped units until unit is properly grounded.

7
Safety - 1266, 1272, 1276 & 1282 Conventional Auger
Safe Operation Instructions
There are several decals on the grain auger and its attachments with safety instructions.
Read and understand these safety alerts before operating.
The shielding has been removed in some of the illustrations for parts demonstration only.
Install all shields before operating the unit.
DANGER
The operator must stop raising the auger before the extending
member is fully extended. Continued lift will cause failure of the
winch, lift cable or auger supports, causing the auger to collapse
which can result in physical damage, personal injury or death.
DANGER
Always disconnect the hydraulic hoses from the tractor after the
auger is raised or lowered to the desired position. Inadvertent
movement of the hydraulic valve on the tractor may cause
damage or personal injury.
DANGER
Winch must be aligned with cable so that the cable does not
stack on one side of the drum. Do not allow the cable to become
slack on winch drum.The cable may recoil and slip over the side
of the drum. In either case, the cable will wind on drum spindle
and cause winch or cable to fail, allowing auger to drop, which
may cause physical damage to the auger or personal injury.
DANGER Never check for hydraulic leaks using any parts of the human
body as oil injection can occur, causing serious injury.

8
Assembly - 1266, 1272, 1276 & 1282 Conventional Auger
Assembly Instructions
Shear bolt failure indicates an overload on the auger.
To remedy the problem:
1. Reduce flow into the intake of the auger. Wet grain requires more power to operate the auger.
The flow must be reduced in wet grain to prevent plugging and/or shear bolt failure.
2. Make certain the auger is running at the correct speed. Run the tractor PTO at 540 RPM (1000
RPM for certain models) for the correct flighting speed. Slowing the auger will allow it to
overload and plug.
3. Check for foreign objects (sacks, cans, rags, etc.) in the tube. Objects may go part way up the
tube and wedge between the flights, blocking the grain flow.

9
Assembly - 1266, 1272, 1276 & 1282 Conventional Auger
Keep all shields in place during operation.

10
Assembly - 1266, 1272, 1276 & 1282 Conventional Auger

11
Assembly - 1266, 1272, 1276 & 1282 Conventional Auger
One must use extreme caution when assembling this auger. Lifting devices (i.e. loader tractor,
forklift, etc.) are required as well as various wrenches and tools. Assemble the auger on a flat
surface. Right, left, front and back refer to looking at the auger from the intake end.
1. Lay the top (Ref. #1) and bottom (Ref. #2) auger tubes flat with the center flange joint spaced
two feet apart.
2. Fasten the flighting assemblies with two fine thread nuts and bolt combinations (Ref. #14)
and one socket head screw, nut and lockwasher combination (Ref. #15). Fasten the flighting
assemblies so that the lower assembly (Ref. #4) overlaps the upper assembly (Ref. #3).
3. Slide the track car (Ref. #50) onto the end of the track (with the end containing the 2-1/2" x
3-1/2" slot in the bottom plate facing towards the intake end of the auger). Place the driveline
coupler onto the driveline section (Ref. #6C) using the 3/8" x 4-1/2" key (Ref. #10) and the 1/4" x
2-3/4" bolt, nut and lockwasher.
NOTE:The track car and driveline coupler must be installed before the tubes are joined.
4. Be sure tubes are straight. Slide the tubes together and connect at flange ring with the 1/2" x
1-1/2" Grade 5 bolt, nut and lockwasher combinations (Ref. #25). NOTE: DO NOT fully tighten
bolts in flange ring connection the first time. Work around the flange at least twice to gradually
pull the connection together. Fully tightening the bolts on one side will pull the auger tubes
out of alignment. Be sure the driveline coupler (Ref. #7) and the 3/8" x 4-1/2" key (Ref. #10) slide
onto the driveline sections (Ref. #6B and #6C). Install the driveline shield splice (Ref. #45).
5. Mount the truss riser assembly (Ref. #27) using 1/2" x 1" bolt, nut and lockwasher combinations
(Ref. #26). Install the truss cables (Ref. #29) using two cable clamps (Ref. #32) and one cable
thimble (Ref. #31) on the upper cable ends. Also, cable clamps (Ref. #32) are to attach the cable
to the top of the truss risers.Tighten the cables to keep the auger straight.
6. Clamp the intake cage (Ref. #91) to the lower tube using 1/2" x 4" bolt, nut and lockwasher
combinations (Ref. #93). Be sure to have 1/2" clearance between the flight core and the bearing.
NOTE: Thrust load must be carried at the top of the auger.
7. Attach the worm winch (Ref. #49) to the mount on the underside of the lower tube using the
3/8" x 1" bolt, nut and lockwasher combination (Ref. #48). Rotate the motor and mount until
ports are on the correct side, then tighten the setscrew on the motor mount (Ref. #49).
8. Add No. 90 gear lube to gearbox until 1/2 full. The Gear box is shipped dry from the factory.

12
Assembly - 1266, 1272, 1276 & 1282 Conventional Auger
9. Assemble the undercarriage.
- Attach rear lift arms (Ref. #35R) to axle by sliding the spindle with hub (Ref. #59) through lift
arm end into the axle. Bolt using 1/2" x 3-1/2" bolt, nut and lockwasher combination (Ref.
#58). (Front support arms should be between bolt and rear lift arm).
- Mount wheels (Ref. #43).
- Attach to the auger by lifting the auger tube and moving the undercarriage assembly under
the tube. Attach the front arms to the lower undercarriage mount on the tube by sliding
arms over the rod and inserting two 3/16" x 1-1/2" cotter pins (Ref. #58). Secure the arms by
inserting two 3/8" x 1" bolt, nut and lockwasher combination (Ref. #48) into the cross bracing.
Attach the extending member to the track car with the track car pin (Ref. #51). Secure track
car pin with 3/16" x 1-1/2" cotter pin (Ref. #53). Assemble front and rear cross members (Ref.
#19) using 3/8" x 5" bolt, nut and lockwasher (Ref. #21).
10. Thread the cable (see CableThreading Diagram).
- Start at the top of the winch drum, go over support arm cross brace by lower undercarriage
mount and go through stop weldment at center flange (not around sheave);
- to track car sheave #1 (must go around side opposite sheave #3 in extending arm first);
- to sheave #2 in stop weldment at center flange (must go over top side first);
- to sheave #3 on yoke end of extending member (4" x 6" tube);
Check that cables are parallel and do not cross.
- down through 4" x 6" tube to small sheave #4 on lower end of extending member (fish tape
is highly recommended);
- up the lower side of extending member to sheave #5 on lower slide plate;
- down to large sheave #6 on lower end of extending member;
- up the top side of extending member to anchor point. Use two 5/16" cable clamps.
Check that cables are parallel and do not cross.
NOTE: Proper raising sequence is the track car moving first until it travels the length of track to
track stop at center flange. Extending member then extends to full height.
NOTE:The operator MUST stop raising the auger before the extending member is fully extended.
(See DANGER statement near Safe Operating Instructions).

13
Assembly - 1266, 1272, 1276 & 1282 Conventional Auger
CAUTION
When cycling the raising mechanism the first time, stop lifting
after the extending member has moved approximately one foot.
Then lower to be sure extending member will retract. If it will not
retract, investigate for problems.
11. Attach stop flags (Ref. #123 and #124) to the stop flag weldment (Ref. #120) using the 1/4" x 2"
cotter keys (Ref. #125) with the lettering facing up and toward the discharge end of the auger.
12. See separate assembly instructions for the different drive packages.
ALERT
Do not operate the auger empty during the break-in period.
For the best results, do not full feed the intake for the first 500
bushels. After break-in, never run auger at slow idle when full
feeding the auger.The worm winch should be greased annually.
Five grease zerks are located on the winch.
Assembly Instructions - 540 RPM PTO Drive
1. Attach the implement input driveline (IID) (Ref. #82) to the gearbox with 3/8" x 2" key (Ref. #82)
and 1/4" x 2-1/4" spiral pin (Ref. #82).
2. Mount the gearbox shield (Ref. #78) using 5/8" x 1" bolt and lockwasher (Ref. #77).
NOTE: Use a 3/8" x 1-1/4" Grade 5 shear bolt. Using other than a Grade 2 bolt may result in
damage to drive components.
NOTE: 540 RPM drive cannot be converted to electric drive without changing gearbox.
Gearbox is shipped dry from the factory.
Add No. 90 gear lube until 1/2 full.

14
Assembly - 1266, 1272, 1276 & 1282 Conventional Auger
Assembly Instructions - 1000 RPM PTO Drive
1. Attach the implement input driveline (IID) (Ref. #82) to the gearbox with 5/16" x 1-3/4" key
(Ref. #82) and 1/4" x 2-1/4" spiral pin (Ref. #82).
2. Mount the gearbox shield (Ref. #78) using 5/8" x 1" bolt and lockwasher (Ref. #77).
NOTE: 1000 RPM drive can be converted to electric drive without changing gearbox.
Gearbox is shipped dry from the factory.
Add No. 90 gear lube until 1/2 full.
NOTE: Use a 5/16" x 1-1/4" Grade 5 shear bolt.
Using other than a Grade 5 bolt may result in
damage to drive components.

15
Assembly - 1266, 1272, 1276 & 1282 Conventional Auger
Assembly Instructions - Electric Drive
1. Assemble the electric mount top support clamp (Ref. #97) and the lower clamp (Ref. #105) on
the tube above the gearbox using 1/2" x 4" bolt, nut and lockwasher (Ref. #107).
2. Attach the gearbox shield (Ref. #95) and the electric motor mount assembly (Ref. #96) onto
the gearbox and onto the top support clamp using four 5/8" x 1" bolt, nut and lockwasher
combinations (Ref. #77).
3. Mount the 11-3/8" x 4-groove pulley (Ref. #101) onto the gearbox using the 5/16" x 2" key (Ref.
#103) and the Q.D. bushing (Ref. #102).
4. Mount the belts (Ref. #104). Mount the belt shield (Ref. #99) using the shield support bar (Ref.
#100) and the 3/8" x 1" bolt, nut and lockwasher combinations (Ref. #98).
NOTE: This option requires a 7" O.D. x 4-groove pulley for 1750 RPM motor (not furnished)
Gearbox is shipped dry from the factory.
Add No. 90 gear lube until 1/2 full.

16
Parts - 1266, 1272, 1276 & 1282 Conventional Auger
Parts List - 1266, 1272, 1276 and 1282 Conventional Auger
Ref
No. Part No. Description Qty 66
Qty
72
Qty
76
Qty
82
1 SZ126697T19 AugerTube (Top Half) w/ Head & Bearing
Brackets 1
SZ000377 AugerTube (Top Half) w/ Head & Bearing
Brackets* 1
SZ127297T19 AugerTube (Top Half) w/ Head & Bearing
Brackets 1
SZ000379 AugerTube (Top Half) w/ Head & Bearing
Brackets* 1
SZ127697T19 AugerTube (Top Half) w/ Head & Bearing
Brackets 1
SZ000243 AugerTube (Top Half) w/ Head & Bearing
Brackets* 1
SZ128297T19 AugerTube (Top Half) w/ Head & Bearing
Brackets 1
SZ000381 AugerTube (Top Half) w/ Head & Bearing
Brackets* 1
2 SZ126697T29 AugerTube (Lower Half) 1
SZ000378 AugerTube (Lower Half)* 1
SZ127297T29 AugerTube (Lower Half) 1
SZ000380 AugerTube (Lower Half)* 1
SZ127697T29 AugerTube (Lower Half) 1
SZ000241 AugerTube (Lower Half)* 1
SZ128297T29 AugerTube (Lower Half) 1
SZ000382 AugerTube (Lower Half)* 1
3 SZ12669301 Flighting Assembly (Top Half) 1
SZ12729301 Flighting Assembly (Top Half) 1
SZ12769301 Flighting Assembly (Top Half) 1
SZ12829301 Flighting Assembly (Top Half) 1
4 SZ12669302 Flighting Assembly (Lower Half) 1
SZ12729302 Flighting Assembly (Lower Half) 1
SZ12769302 Flighting Assembly (Lower Half) 1
SZ12829302 Flighting Assembly (Lower Half) 1
5 SZ60058451 5/8" x 4-1/2" Grade 5 Flighting Drive Bolt 1 1 1 1
6A SZ4127417 Driveline Section 164" Long (Under Shield) 1
SZ4127416 Driveline Section 200" Long (Under Shield) 1
SZ4127414 Driveline Section 224" Long (Under Shield) 1
SZ4127413 Driveline Section 236" Long (Under Shield) 1
6B SZ4127415 Driveline Section 216" Long (Under Shield) 1 1 1
* Galvanized

17
Parts - 1266, 1272, 1276 & 1282 Conventional Auger
Ref
No. Part No. Description Qty 66
Qty
72
Qty
76
Qty
82
SZ4127420 Driveline Section 240" Long (Under Shield) 1
6C SZ4127425 Driveline Section 204" Long (Under Shield) 1
SZ4127415 Driveline Section 216" Long (Under Shield) 1 1 1
6D SZ 4127427 Driveline Section 95" Long (Under Shield) 1
SZ 4127426 Driveline Section 119" Long (Under Shield) 1
SZ4127424 Driveline Section 143" Long (Under Shield) 1
SZ4127423 Driveline Section 179" Long (Under Shield) 1
6E SZ4127435 Driveline Section 48" Long (Under Shield) 1 1 1 1
7 SZ4127405 Driveline Coupler 4 4 4 4
8 SZ4957722 60-22 Sprocket w/ 1-1/2" Diameter Keyed Hub 2 2 2 2
SZ0113820 3/8" x 2" Key 2 2 2 2
9 SZ0043622 #60 Double Chain w/ Connector Link 1 1 1 1
10 SZ0113845 3/8" x 4-1/2" Key 4 4 4 4
11 SZ6002527 1/4" x 2-3/4" Bolt, Nut & Lockwasher 4 4 4 4
12 SZ6007022 7/16" x 2-1/4" Spiral Pin 2 2 2 2
14 SZ6875035 1/2" x 3-1/2" FineThread, Bolt & Locknut 2 2 2 2
15 SZ6003878 3/8" x 7/8" Socket Head Screw, Nut &
Lockwasher 1 1 1 1
19 SZ7124363 63" Cross Bar Weldment 1
SZ7124374 74" Cross Bar Weldment 1 1 1
SZ7124384 84" Cross Bar Weldment 1 1 1
SZ7124394 94" Cross Bar Weldment 1
21 SZ6003850 3/8" x 5" Bolt, Nut & Lockwasher 4 4 4 4
22 SZ09312932 Tow Hitch 1 1 1 1
23 SZ60012035 1/2" x 3-1/2" Bolt, Nut & Lockwasher 1 1 1 1
24 SZ2016121 #3 Wood Intake Bearing 1 1 1 1
25 SZ6001515 1/2" x 1-1/2" Grade 5 Bolt, Nut & Lockwasher 15 15 15 15
26 SZ6001201 1/2" x 1" Bolt, Nut & Lockwasher 4 4 4 4
27 SZ2032320 CableTruss Support 2 2 2 2
28 SZ66HHNNCP3/80 3/8" Hex Nut 4 4 4 4
29 SZ2038438 1/4" x 38'Truss Cable W/Eyebolt 2 2 2 2
31 SZ6009104 1/4" CableThimble 2 2 2 2
32 SZ6003104 1/4" Cable Clamp 8 8 8 8
34 SZ0211105 105" Undercarriage Axle 1
SZ0211126 126" Undercarriage Axle 1 1 1
35F SZ7124103 212" Front Undercarriage Arm 2
SZ7124105 232" Front Undercarriage Arm 2
SZ7124107 243" Front Undercarriage Arm 2
SZ7124109 264" Front Undercarriage Arm 2
35R SZ7124201 168" Rear Undercarriage Arm 2

18
Parts - 1266, 1272, 1276 & 1282 Conventional Auger
Ref
No. Part No. Description Qty 66
Qty
72
Qty
76
Qty
82
SZ7124205 217" Rear Undercarriage Arm 2 2 2
36 SZ7124050 105" Extension Arm 1
SZ7124060 120" Extension Arm 1 1
SZ7124080 150" Extension Arm 1
37 SZ7124411 Top HalfTelescoping Head Weldment 1 1 1 1
SZ7124412 Bottom HalfTelescoping Head Weldment 1 1 1 1
SZ0319311 Rear Arm SlideTop Wear Pad 1/4" x 1" x 5-1/2"
Nylon Bar 4 4 4 4
SZ0319310 Rear Arm Slide Side Wear Pad 1/4" x 1" x 3-1/2"
Nylon Bar 4 4 4 4
39 SZ6003855 3/8" x 5-1/2" Bolt, Nut & Lockwasher 18 18 18 18
40 SZ6001515 1/2" x 1-1/2" Grade 5 Bolt, Nut & Lockwasher 8 8 8 8
43 SZ103994 16" 6-Bolt Wheel 2 2 2 2
44 SZ1630383 383"Top Driveline Shield 1
SZ1630419 419"Top Driveline Shield 1
SZ1630433 433"Top Driveline Shield 1
SZ1630479 479"Top Driveline Shield 1
45 SZ1629310 12" Driveline Shield Splice 1 1 1 1
47 SZ6003115 3/16" - 10 x 1-1/2" Self-Starting Shield Screw 26 26 28 32
48 SZ6003801 3/8" x 1" Bolt, Nut & Lockwasher 7 7 7 7
49 SZ2001090 Winch Assembly 1 1 1 1
SZ2019201 Stationary Hydraulic Motor Mount 1 1 1 1
SZ3981080 Hydraulic Motor 1 1 1 1
SZ6003870 3/8" x 3/4" Bolt & Lockwasher 4 4 4 4
50 SZ7125005 Track Car w/ Sheave 1 1 1 1
51 SZ0319312 3/4" x 7-5/8"Track Car Pin 1 1 1 1
52 SZ6009516 5/16" CableThimble 1 1 1 1
53 SZ6003615 3/16" x 1-1/2" Cotter Pin 3 3 3 3
54 SZ6003516 5/16" Cable Clamp 2 2 2 2
56 SZ0215120 5/16" x 120' Winch Cable 1
SZ0215130 5/16" x 130' Winch Cable 1
SZ0215135 5/16" x 135' Winch Cable 1
SZ0215148 5/16" x 148' Winch Cable 1
58 SZ6001203 1/2" x 3-1/2" Bolt, Nut & Lockwasher 2 2 2 2
59 SZ0211115 Undercarriage Spindle & 6-Bolt Hub Assembly,
Bolt-In 2 2 2 2
60 SZ2011051 1-1/2" Head Cap Bearing w/ Lock Collar 4 4 4 4
61 SZ6001205 1/2" x 1-1/2" Bolt, Nut & Lockwasher 16 16 16 16
62 SZ65080MSCI000 1-1/2" 4-Bolt Bearing Flange 8 8 8 8
63 SZ4121276 Driveline Extension Shaft w/ 100-22 Sprocket 1 1 1 1

19
Parts - 1266, 1272, 1276 & 1282 Conventional Auger
Ref
No. Part No. Description Qty 66
Qty
72
Qty
76
Qty
82
64 SZ0431282 Flight Extension Shaft w/ 100-30 Sprocket 1 1 1 1
66 SZ0231150 1-1/2" 10 ga Machine Bushing 3 3 3 3
67 SZ0043044 #100 Chain x 44 Pitch w/ Connectors 1 1 1 1
68 SZ8481282 Face Plate w/ Access Hole & Flanges 1 1 1 1
69 SZ8481202 Head Cap Band 1 1 1 1
70 SZ6005617 5/16" x 1-1/2" Bolt, Nut & Lockwasher 1 1 1 1
71 SZ8401809 Access Plug 1 1 1
72 SZ665/8X11/200 5/8" x 1-1/2" Bolt 1 1 1 1
SZ990218480001 2-1/4" O.D. x 5/8" ID x 1/4"Thrust Washer 1 1 1 1
SZ66STLWP05/80 5/8" Lockwasher 1 1 1 1
73 SZ2010243 1-1/2" Wood Bearing 11 11 12 14
73C SZ651.50SFTCLR 1-1/2" Shaft Collar 2 2 2 2
74 SZ65080MSCI000 1-1/2" 4-Bolt Bearing Flange 22 22 24 28
75 SZ6001201 1/2" x 1" Bolt, Nut & Lockwasher 22 22 24 28
76 SZ0169782 540 RPM Gearbox, 1:1 Ratio 1 1 1 1
SZ0169776 1000 RPM Gearbox, 1.81-1 Ratio Optional
77 SZ6005811 5/8" x 1" Bolt & Lockwasher 8 8 8 8
78 SZ1621281A PTO Gearbox Shield 1 1 1 1
79 SZ0311282A Gearbox Mount Weldment 1 1 1 1
80 SZ0311283 Gearbox Lower Clamp 2 2 2 2
81 SZ6000504 1/2" x 4" Bolt, Nut & Lockwasher 4 4 4 4
82 SZ0163572 540 RPM Implement Input Driveline w/ Shear
Clutch 1 1 1 1
SZ6003810 3/8" x 1-1/4" Grade 5 Shear Bolt & Locknut 1 1 1 1
SZ0113820 3/8" x 2" Key 1 1 1 1
SZ60025111 1/4" x 2-1/4" Spiral Pin 1 1 1 1
82 SZ0161472 1000 RPM Implement Input Driveline w/ Shear
Clutch Optional
SZ6005613 5/16" x 1-1/4" Grade 5 Shear Bolt & Locknut 1 1 1 1
SZ0113122 5/16" x 1-3/4" Key 1 1 1 1
SZ60025111 1/4" x 2-1/4" Spiral Pin 1 1 1 1
85 SZ1628815 PTO Rod Hanger Bracket 1 1 1 1
86 SZ6003801 3/8" x 1" Bolt, Nut & Lockwasher 1 1 1 1
87 SZ1630344 344" Lower Driveline Shield 1
SZ1630404 404" Lower Driveline Shield 1
SZ1630419 419" Lower Driveline Shield 1
SZ1630440 440" Lower Driveline Shield 1
91 SZ09312931 Intake Cage 1 1 1 1
93 SZ6000504 1/2" x 4" Bolt, Nut & Lockwasher 4 4 4 4
95 SZ5951280 Electric Gearbox Shield 1 1 1 1
96 SZ59512661 Electric Motor Mount Assembly 1 1 1 1

20
Ref
No. Part No. Description Qty 66
Qty
72
Qty
76
Qty
82
97 SZ1621289 Electric MountTop Support Clamp 1 1 1 1
98 SZ6003801 3/8" x 1" Bolt, Nut & Lockwasher 4 4 4 4
99 SZ1621286 Electric Belt Shield 1 1 1 1
100 SZ1621287 Belt Shield Support Bar 1 1 1 1
101 SZ0164011 11-3/8" x 4 Groove Pulley (Under Shield) 1 1 1 1
102 SZ0164137 1-3/8" ID QD Bushing (Under Shield) 1 1 1 1
103 SZ0113122 5/16" x 2" Key (Under Shield) 1 1 1 1
104 SZ2221670A 70" V Belt, Matched Set of 4 (Under Shield) 1 1 1 1
105 SZ0311283 Lower Support Clamp 1 1 1 1
106 SZ6001201 1/2" x 1" Bolt, Nut & Lockwasher 2 2 2 2
107 SZ6000504 1/2" x 4" Bolt, Nut & Lockwasher 2 2 2 2
110 SZ9900694 Relief Door 1 1 1 1
111 SZ60038252 3/8" x 2-1/2" Bolt & Double Nut 1 1 1 1
112 SZ6003822 3/8" x 2" Bolt & Double Nut 1 1 1 1
113 SZ80.500X5.7 1/2" x 5-3/4" Spring 2 2 2 2
120 SZ7124051 Stop Flag Action Arm 1 1 1 1
SZ80.375X4.0 Stop FlagTension Arm 1 1 1 1
SZ6002503 1/4" x 1" Bolt & Self-Locking Nut 2 2 2 2
123 SZ7124052 Right Hand Stop Lift Sign 1 1 1 1
124 SZ7124053 Left Hand Stop Lift Sign 1 1 1 1
130 SZ0116021 6-Bolt Hub w/Cups 2 2 2 2
131 SZLM48510 Inner Bearing Cup 2 2 2 2
132 SZ0203549 Grease Seal 2 2 2 2
133 SZLM48548 Inner Bearing Cone 2 2 2 2
134 SZ60X102X10WHL 1/2" x 1" Wheel Bolts 12 12 12 12
135 SZDC13 Dust Cap 2 2 2 2
136 SZLM67048 Outer Bearing Cone 2 2 2 2
137 SZLM67010 Outer Bearing Cup 2 2 2 2
138 SZ600X15016WA 2" x 15/16" Spindle Washer 2 2 2 2
139 SZ600NUT0SLOT0 Slotted Spindle Nut 2 2 2 2
140 SZ66C5/32X11/4 5/32" x 1-1/4" Cotter Pin 2 2 2 2
141 SZ29700 Owner‘s Manual Container 1 1 1 1
142 SZ297002 Owner‘s Manual Container Mounting Bracket 2 2 2 2
143 SZ6002575 1/4" x 3/4" Bolt, Nut & Lockwasher 2 2 2 2
144 SZ9900034 Owner‘s Manual Container Mounting Plate 1 1 1 1
Parts - 1266, 1272, 1276 & 1282 Conventional Auger