Farpointe Data RANGER EDGE Use and care manual

REFERENCE DOCUMENT
RANGER®EDGE RECEIVER CONFIGURATION
The Ranger Edge Receiver, a unique member of the Ranger line of long-range Receivers, offers single location point of control with all set-up and
configuration done directly on the unit, eliminating the requirement for separate mobile smartphone or PC programming devices.
The dip switches are set to the 0-position by default.
1.0 Selecting Transmitter Button To Operate Relay
Dip switches 10 and 11 select which button on a Transmitter will
operate the relay (see below). It is only possible to select a single
Transmitter button per Edge Receiver (Button 1, 2, 3 or 4). The button
selected for relay operation will be the same for all Transmitters
enrolled in that specific Edge Receiver.
2.0 Enrolling Transmitters
1. Move dip switch 12 to the Program position. The
Program/Run LED will change from off to red.
2. Use dip switches 10 and 11 to select the button
on a Transmitter that will operate the relay.
3. Use dip switches 1 through 9 to select the
enrollment location of the Transmitter.
4. Press the Select Button once. The Status LED
will change from yellow to blue.
5. Within range of the Edge Receiver, press the
selected button on the Transmitter to be enrolled.
The Status LED will change from blue to yellow.
6. To enroll additional Transmitters, repeat 3, 4 and 5.
7. To finish enrolling, move dip switch 12 to the Run position. The
Program/Run LED will change from red to off.
8. To test enrollment of an enrolled Transmitter, press the selected
Transmitter button. The Status LED and Relay LED will turn green
for the active relay time.
3.0 Deleting Transmitters
1. Move dip switch 12 to the Program position. The Program/Run LED
will change from off to red.
2. Use dip switches 1 through 9 to select the desired enrollment
location of the Transmitter to be deleted.
3. Press the Select Button twice in succession. The Status LED will
change from yellow to blue then red.
4. To delete additional enrolled Transmitters, repeat 2 and 3.
5. To finish deleting, move dip switch 12 to the Run position. The
Program/Run LED will change from red to off.
6. To test deletion of a previously enrolled Transmitter press the
Transmitter button that had been deleted. The Status LED will
change from yellow to red.
4.0 Enrolling Credentials
1. Connect a reader supporting the credentials to be enrolled via the
Wiegand interface.
2. Move dip switch 12 to the Program position. The Program/Run LED
will change from off to red.
3. Use dip switches 1 through 9 to select the enrollment location of
the credential.
4. Press the Select Button once. The Status LED will change from
yellow to blue.
The Edge Receiver offers 512 separate enrollment locations, ranging from zero to 511. Each enrollment location may store a unique credential,
such as a Transmitter—or with the addition of a Wiegand-output reader, a card or tag. Dip switch positions 1 thru 9 of the 12-Position Slide Style
Dip Switch are used to select specific individual enrollment locations. Each specific selection represents a binary number. Below are examples of
individual enrollment locations, along with their equivalent binary and decimal number representations.
EXAMPLES:
A. Enrollment Location 3
Set dip switches 3, 4, 5, 6, 7,
8 and 9 to the 0-position, and
dip switches 1 and 2 to the
1-position. (000000011
binary, 3 decimal)
B. Enrollment Location 21
Set dip switches 2, 4, 6, 7, 8
and 9 to the 0-position, and
dip switches 1, 3 and 5 to the
1-position. (000010101
binary, 21 decimal)
C. Enrollment Location 247
Set dip switches 4 and 9 to
the 0-position, and dip
switches 1, 2, 3, 5, 6, 7 and 8
to the 1-position. (011110111
binary, 247 decimal)
D. Enrollment Location 500
Set dip switches 1, 2 and 4 to
the 0-position, and dip
switches 3, 5, 6, 7, 8 and 9 to
the 1-position. (111110100
binary, 500 decimal)
SW1
SELECT
Select Button
PROGRAM
Position
RUN
Position
PROGRAM
12
RUN
PROGRAM
12
RUN
PROGRAM
12
RUN
PROGRAM
12
RUN
11
10
11
10
11
10
11
10
Transmitter
Button 1
Transmitter
Button 2
Transmitter
Button 3
Transmitter
Button 4
Enrollment locations and their equivalent dip switch settings can be confirmed and documented on the Credential Location Worksheet.
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0
9
8
7
6
5
4
3
2
1
H LADDRESS 1
0

5. Present the credential to the reader. Once read by the reader the
Status LED will change from blue to yellow.
6. To enroll additional credentials, repeat 3, 4 and 5.
7. To finish enrolling, move dip switch 12 to the Run position. The
Program/Run LED will change from red to off.
8. To test enrollment of an enrolled credential, present the credential
to the reader. The Status LED and Relay LED will turn green for the
active relay time.
9. Note dip switches 10 and 11, used to select Transmitter button,
are ignored when utilizing a reader connected via the Wiegand
interface.
5.0 Deleting Credentials
1. Move dip switch 12 to the Program position. The Program/Run LED
will change from off to red.
2. Use dip switches 1 through 9 to select the desired enrollment
location of the credential to be deleted.
3. Press the Select Button twice in succession. The Status LED will
change from yellow to blue then red.
4. To delete additional enrolled credentials, repeat 2 and 3.
5. To finish deleting, move dip switch 12 to the Run position. The
Program/Run LED will change from red to off.
6. To test deletion of a previously enrolled credential present the
credential to the reader connected via the Wiegand interface. The
Status LED will change from yellow to red.
6.0 Deleting All Transmitters and Credentials
1. Move dip switch 12 to the Program position. The Program/Run LED
will change from off to red.
2. Set dip switches 1 through 9 to the ‘1’ position (enrollment
location 511).
3. Press the Select Button twice in succession. The Status LED will
change from yellow to blue then red.
4. To finish deleting, move dip switch 12 to the Run position. The
Program/Run LED will change from red to off.
5. To test deletion of a previously enrolled Transmitter press the
Transmitter button that had been selected. The Status LED will
change from yellow to red.
6. To test deletion of a previously enrolled credential present the
credential to the reader. The Status LED will change from yellow
to red.
7.0 Adjusting Relay Activation Time
1. Move dip switch 12 to the Run position. The Program/Run LED will
change from red to off.
2. Adjust dip switches 1 through 4 to select a relay activation time
between approximately 1 and 15 seconds. Timing is adjustable in
approximately one second increments.
3. Press the Select Button once. The Status LED will remain yellow.
4. To test relay activation time with a previously enrolled Transmitter,
press the Transmitter button that had been selected. The Status
LED and Relay LED will turn green for the active relay time.
5. To test relay activation time with a previously enrolled credential,
present the credential to the reader connected via the Wiegand
interface. The Status LED and Relay LED will turn green for the
active relay time.
REFERENCE DOCUMENT
RANGER®EDGE RECEIVER CONFIGURATION
© 2022 Farpointe Data, Inc. All rights reserved. Farpointe Data®, Pyramid
Series Proximity®, Delta®, Ranger®, and CONEKT®are the registered U.S.
trademarks of Farpointe Data, Inc. All other trademarks are the property of
their respective owners.
www.farpointedata.com P/N: 01190-003 ∙ Rev. 1
Farpointe Data, Inc.
2195 Zanker Road
San Jose, CA 95131 USA
Office: [phone]
Fax: [phone]
[email protected]
Farpointe Data reserves the right to
change specifications without notice.
Feb-25-2022
For installation instructions, please review our
Edge Receiver Quick Start Guide.
To assist in the tracking of enrolled Transmitters and/or credentials,
please download the Credential Location Worksheet.
Relay Activation Timing Configurations
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1 second
(default setting)
4
3
2
1
2 seconds
4
3
2
1
3 seconds
4
3
2
1
4 seconds
5 seconds
4
3
2
1
4
3
2
1
4
3
2
1
4
3
2
1
8 seconds
9 seconds
4
3
2
1
10 seconds
6 seconds
7 seconds
4
3
2
1
4
3
2
1
4
3
2
1
11 seconds
12 seconds
4
3
2
1
13 seconds
4
3
2
1
14 seconds
4
3
2
1
15 seconds
4
3
2
1