Fast Mover FT1090 Specification sheet

T: [phone] F: [phone] E: sales@fastmovertoolsuk com
FT1090
Air O erated 2”/3” Mini Sanding Kit
Product Instruc%on Manual
PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
FT1090_Product Instructions 08/10/2014 10:19 Page 1

FT1090
Instruc%on Manual
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
IMPORTANT
Please read through this Manual carefully before using the FT1090
This tool must only be used for sanding and within the arameters
outlined in this manual. All users of the equi ment should be trained in
any risks associated with the roducts they are sanding or using as
finishing aids.
Spec f cat on
Pad Diameter 2”/50mm and 3”/75mm
Pad Thread Size 6
Free Speed 15,000RP
inimum Pad Rated Speed 18,000RP
Operating Pressure 90Psi/6.3BAR
Air Consumption 4CF
Air Inlet 1/4” BSP
Vibration Level 2.06m/s2(uncertainty 0.70m/s2)
Noise Level 84dB(A)
Weight 710g
Length 168mm
Safety Instruct ons
These instructions are intended as a guide to the correct use of this equipment. The process or
materials being sanded may have risk characteristics requiring additional safety measures and
these must be identified by the user. All users of this sander must be thoroughly acquainted with
this manual.
Before Use and Before Us ng Tool for the F rst T me
- ake sure you have the relevant Personal Protection Equipment (PPE).
Hand Protect on
The pad revolves at high speed and may cause damage if bought into contact with
exposed flesh. The workpiece and the pad may also get hot after prolonged use. Hand
protection must be strong enough to protect the skin and be a good fit and have no loose
parts that may get caught in rotating parts.
Determination of the test results includes consideration of measurement
uncertainty from the test equipment and methods.
Tool Use
This Air Operated Sander is designed for the purpose of
sanding a variety of coatings from steel, wood, plastics,
etc.
K t Contents
1 x Air Tool
5 x 75mm Conditioning Discs (Fine, edium & Coarse)
5 x 50mm Conditioning Discs (Fine, edium & Coarse)
1 x 75mm Roll-on Backing Plate
1 x 50mm Roll-on Backing Plate
1 x 75mm Roll-on Velcro Backing Pad
1 x 50mm Roll-on Velcro Backing Pad
FT1090_Product Instructions 08/10/2014 10:19 Page 2

Eye and Breath ng Protect on
The sanding process will create dust and other airborne particles. There is no dust
extraction function on this machine so it is essential that approved eye and breathing
protection is worn.
No se and Ear Protect on
Depending on the material being worked on and the type of sanding disc used, noise
levels may cause hearing damage including temporary or even permanent hearing loss.
It is recommended that Ear Protection is worn at all times when using the sander.
Repet t ve Stra n Injury (RSI)
All products of this nature can cause RSI if used for long period, particulary in an
awkward operating position. Adequate rest periods and working conditions should be
considered for prolonged use.
General Safety Informat on
1 Ensure the sanding pad is equal to or greater than 120% of the stated RP of the
sander.
2 Keep the workplace clean and tidy.
3 Use the tool in a well ventilated area.
4 Air hoses can present a trip hazard, always keep hoses in a way that minimises trip
hazards.
5 DO NOT hold the workpiece by hand, always make sure the workpiece is clamped
securely.
6 Keep all flammable and combustible materials away from the work area.
7 Children and other unauthorised persons should be kept away from the work area.
8 NEVER use the sander whilst the floor underfoot is wet or slippery.
9 NEVER use the sander when standing on an unstable surface.
10 Keep the sander out of reach of children.
11 Analyse the material you are sanding. Be aware of the dangers of sanding lead based
paints. Historically, paint contained lead and sanding such paint will cause toxic dust. If
you suspect that lead could be in the paint the following actions must be observed;
- Alert any other persons in the nearby and keep them away from the working
area.
- Use specific air fed respirator, PE coated coveralls and latex gloves.
- Dispose of any dust and paint waste correctly and thoroughly clean the
workpiece and working area after the sanding has finished.
12 NEVER attempt to sand materials containing asbestos.
13 VIBRATION. Hand held air tools may produce vibration. Vibration from sanders can
cause disease. The use of gloves will help reduce the risk and can help prevent injury.
14 Disconnect the air supply before changing disc or pad.
15 Ensure the sander has stopped rotating before putting it down or handling the pad or
disc.
16 NEVER carry the sander by the air hose.
17 NEVER point the sander at other persons.
18 NEVER operate the sander whilst under the influence or drugs, alcohol or intoxicating
medication.
19 Check you have no loose clothing, hair, jewellery or any other items of a personal nature
that might become entangled with the rotating parts.
20 Check you have a maximum inlet air pressure of 90PSI/6.3BAR.
PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
FT1090_Product Instructions 08/10/2014 10:19 Page 3

FT1090
Instruc%on Manual
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
Fig. 1
Air Fil er/Regula or
/Lubrica or
Whip
Hose
Airline
Air Fi ing
Quick Release Air Coupling
To Air Tool
Fig. 2
We recommend that your a r tool s connected to the
ma n a rl ne n the way d splayed n F g. 2.
1: Air Tool
2: Whip Hose/Leader Hose
3: Air Fitting
4: Quick Coupling
5: ain Air Hose
5
1
4
3
2
Air
Source
Fam l ar se Yourself w th the Controls
1 The throttle is pressure sensitive.
Applying pressure will increase
rotational speed.
2 Removal of all pressure will stop the
machine.
3 This model is fitted with a safety
lock to prevent accidental starting.
This should be locked at all
times when the sander is left under
power.
4 Never leave the tool unattended and
connected to the power supply.
Dur ng Use
1 When using the sander for long periods of time, check the sanding disc for wear.
2 Replace worn discs as worn or clogged discs will make the sander inefficient.
3 The sanding operation will cause heat. Check the material that is being worked on that it
is not getting too hot. If this is occurring, stop sanding to allow the material to cool down.
4 You can adjust the speed of the tool by adjusting the pressure you apply to the throttle.
5 ake regular checks on the sanding pad for wear and damage and replace them
immediately.
6 Due to the potential heat caused by the sanding process, keep flammable liquids and
gases well away from the work area.
Installat on
1 Check the tool over to make sure no part is missing or damaged.
2 Fitting an Air Filter, Regulator and Lubricator is recommended.
3 Refer to Fig. 1 for the recommended airline setup.
Backing
Plate Safety Lock
Handle
Throttle
Exhaust
Inlet
Conditioning Disc
FT1090_Product Instructions 08/10/2014 10:19 Page 4

PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
4 It is strongly advised that you always use a Whip Hose/Leader Hose in combination with
Quick Release Couplings. See Fig. 2 for recommended setup.
5 Water in the air supply will cause the internal bearing of the tool to rust and eventually
seize.
6 ake sure that your airline is free from water at all times.
7 Always select the correct sanding disc grit for the job.
Tools Included w th your Sander
1 x High Flow ale Air Fitting
1 x Spanner
1 x Oil Pot
Ma ntenance
1 If the air supply is not lubricated sufficiently it will be necessary to lubricate the tool
directly. This can be done by disconnecting the air hose and pouring in 5ml of air tool oil
into the Air Inlet. Read safety data sheet or instructions on use of oil to ensure safe
usage. These can be obtained from your supplier.
2 Replace worn or damaged parts using genuine parts only.
3 Store tool in a dry area, do not allow tool to be immerse in water or used/stored in wet
conditions.
FT1090_Product Instructions 08/10/2014 10:19 Page 5

FT1090
Instruc%on Manual
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
No. Code Description Q’ty
1 FT1090/1 Retainer 1
2 FT1090/2 O-Ring 1
3 FT1090/3 Valve Housing 1
4 FT1090/4 Hush 1
5 FT1090/5 O-Ring 1
6 FT1090/6 Valve 1
7 FT1090/7 O-Ring 1
8 FT1090/8 Spring 1
9 FT1090/9 Speed 1
10 FT1090/10 O-Ring 1
11 FT1090/11 O-Ring 1
12 FT1090/12 Nut 1
13 FT1090/13 Packing 1
14 FT1090/14 Ball Bearing 1
15 FT1090/15 Rear Endplate 1
16 FT1090/16 Spring Pin 1
17 FT1090/17 Rotor Blade 4
18 FT1090/18 Rotor 1
19 FT1090/19 Washer 1
20 FT1090/20 Cylinder 1
21 FT1090/21 Ball 1
22 FT1090/22 Front Plate 1
23 FT1090/23 Ball Bearing 1
24 FT1090/24 Bevel Gear 1
25 FT1090/25 Housing 1
26 FT1090/26 Spring Pin 1
27 FT1090/27 Control Lever 1
28 FT1090/28 Ball Bearing 1
29 FT1090/29 Bevel Gear 1
30 FT1090/30 Ball Bearing 2
No. Code Description Q’ty
31 FT1090/31 Key 1
32 FT1090/32 Chuck Casing 1
33 FT1090/33 Retainer 1
34 FT1090/34 Collet 1
35 FT1090/35 Clamp Nut 1
36 FT1090/36 Oil Cap 1
37 FT1090/37 Wrench (14 & 17mm) 1
Parts D agram
50/75mm ini Air Operated Sander
FT1090_Product Instructions 08/10/2014 10:19 Page 6

PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
Warranty
We hope that you will be very happy with your purchase. If you do have a problem with your tool,
you have the added peace of mind of a 6 month warranty, which comes into date from the date of
purchase (proof of purchase required).
Scope of Warranty
- The warranty will cover you from all faults caused by defective components or poor workmanship.
- Tools sent outside the EU are not covered by this warranty.
- Product must be returned to us, the warranty does not cover cost of carriage.
- If the product is no longer in manufacture, it will be replaced with a tool of equivalent or higher
specification.
What s not covered
- Normal wear and tear caused by use in accordance with the operating instructions.
- Replacement of any provided accessories, such as Backing Pads, Airline Connections, Air
Fittings, Blades, Spanners, etc.
- Accidental damage, faults caused by negligent use or care, neglect, misuse or careless operation,
handling and storage of the product.
- odification of, or change of, any part of this product in any way.
- Faults caused by use of non compatible accessories.
- Tool seizure caused by insufficient oiling.
- Faults caused by incorrect installation.
- Repairs or alterations carried out by non-approved parties.
- Traces of water or rust inside tool - this shows that a properly working air filter has not been used.
Val d ty
- This warranty is valid for 6 months after date of purchase.
- Warranty is rendered invalid if;
- Tool is taken apart for any reason without our consent.
- Tool is not oiled daily.
- Air supply line is not used with a properly working air filter.
- A warranty claim will not be accepted without an official proof of purchase from your supplier.
Warranty Ver f cat on
Please keep this manual with your tool for the purpose of verifying your
warranty. Fill in box below to validate warranty.
Fax to 01582 667100
Tool Code: FT1090
Place of Purchase
____________________________________________
____________________________________________
_____________ Post Code __________________
Date
___________________________________________
Your Details
Company ________________________
Address ________________________
________________________________
Post Code________
Email ________________________
FT1090_Product Instructions 08/10/2014 10:19 Page 7

FT1090
Instruc%on Manual
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
Declarat on of Conform ty
We declare that the equipment detail below, to the best of our knowledge and
ability, complies with the following Directive.
achinery Directive - 2006/42/EC and amending Directives
Equipment Description 50/75mm ini Air Operated Sander
Part Code FT1090
Distributed in the EU by Fast over Tools
Address Unit 1 Frenchs Avenue
Dunstable
Bedfordshire
LU6 1BH
United Kingdom
The following Transposed Harmonised Standards have been applied in the
design and construction of this equipment:
EN ISO 28927-3:2009 Hand-held portable power tools - Test methods for evaluation of
vibration emission - Part 3: Polisher and rotary, orbital and random
orbital sanders
EN ISO 11148-8:2011 Hand-held non-electric power tools. Safety requirements. Sanders
and polishers
EN ISO 15744:2008 Hand-held non-electric power tools. Noise measurement code.
Engineering method (grade 2)
The manufacturer and the distributor, stated above, hold the Technical Construction File for this
equipment.
Signed on behalf of the distributor
(the responsible person) …………………………………………
Name: Brian offitt
Position: Director
Date and Place: Dunstable, UK
Please look after the environment, dispose of all packaging in a responsible way.
Always dispose of tools in accordance with local authority guidelines.
© 2014 Fast over Tools Ltd. This document is copyright and is not to be copied, circulated, distributed or shown
to anyone other than the intended recipient without the express permission of Fast over Tools Ltd and it’s
Directors.
Revision
08.10.14
FT1090_Product Instructions 08/10/2014 10:19 Page 8