Fast Mover FT900 Specification sheet

T: [phone] F: [phone] E: sales@fastmovertoolsuk com
FT900
Air O erated 75mm Polisher Kit
Product Instruc%on Manual
PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
FT900_Product Instructions 09/10/2014 08:07 Page 1

FT900
Instruc%on Manual
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
IMPORTANT
Please read through this Manual carefully before using the FT900
This tool must only be used for olishing and within the arameters
outlined in this manual. All users of the equi ment should be trained in
any risks associated with the roducts they are olishing or using as
finishing aids.
Specification
Pad Diameter 3”/75mm
Tool Thread Size M6 Male
Free Speed 2,800RPM
Minimum Pad Speed 3,360RPM
Operating Pressure 90Psi/6.3BAR
Air Consumption 4CFM
Air Inlet 1/4” BSP
Vibration Level 6.56m/s
oise Level 88.4dB(A)
Weight 810g
Length 138mm
Safety Instructions
These instructions are intended as a guide to the correct use of this equipment. The process or
materials being polished may have risk characteristics requiring additional safety measures and
these must be identified by the user. All users of this polisher must be thoroughly acquainted with
this manual.
Before Use and Before Using Tool for the First Time
- Make sure you have the relevant Personal Protection Equipment (PPE).
Hand Protection
The pad revolves at high speed and may cause damage if bought into contact with
exposed flesh. The workpiece and the pad may also get hot after prolonged use. Hand
protection must be strong enough to protect the skin and be a good fit and have no loose
parts that may get caught in rotating parts.
Determination of the test results includes consideration of measurement
uncertainty from the test equipment and methods.
Kit Contents
1 x FT900 Air Polisher
1 x FMT7007 3” Roll-on Backing Plate
1 x FMT7095 3” Roll-on Backing Pad
1 x FMT4060 3” Roll-on Lambswool Bonnet
1 x FMT7009/OR 3” Roll-on Polishing Head
1 x FMT7001 3” Roll-on Wool Wheel
1 x Oil Pot
1 x Spanner
1 x Air Fitting
Tool Use
This Air Operated Mini Polisher can be used to polish a
large range of painted or varnished surfaces.
FT900_Product Instructions 09/10/2014 08:07 Page 2

Eye and Breathing Protection
The polishing process may create dust and other airborne particles. There is no dust
extraction function on this machine so it is essential that approved eye and breathing
protection is worn.
Noise and Ear Protection
Depending on the material being worked on and the type of polishing disc used, noise
levels may cause hearing damage including temporary or even permanent hearing loss.
It is recommended that Ear Protection is worn at all times when using the polisher.
Repetitive Strain In ury (RSI)
All products of this nature can cause RSI if used for long period, particulary in an
awkward operating position. Adequate rest periods and working conditions should be
considered for prolonged use.
General Safety Information
1 Ensure the polishing pad is equal to or greater than 120% of the stated RPM of the
polisher.
2 Keep the workplace clean and tidy.
3 Use the tool in a well ventilated area.
4 Air hoses can present a trip hazard, always keep hoses in a way that minimises trip
hazards.
5 DO OT hold the workpiece by hand, always make sure the workpiece is clamped
securely.
6 Keep all flammable and combustible materials away from the work area.
7 Children and other unauthorised persons should be kept away from the work area.
8 EVER use the polisher whilst the floor underfoot is wet or slippery.
9 EVER use the polisher when standing on an unstable surface.
10 Keep the polisher out of reach of children.
11 Analyse the material you are polishing. Be aware of the dangers of polishing lead based
paints. Historically, paint contained lead and polishing such paint may cause toxic
particles to enter the atmosphere. If you suspect that lead could be in the paint the
following actions must be observed;
- Alert any other persons in the nearby and keep them away from the working
area.
- Use specific air fed respirator, PE coated coveralls and latex gloves.
- Dispose of any dust and paint waste correctly and thoroughly clean the
workpiece and working area after the polishing has finished.
12 EVER attempt to sand materials containing asbestos.
13 VIBRATIO . Hand held air tools may produce vibration. Vibration from polishers can
cause disease. The use of gloves will help reduce the risk and can help prevent injury.
14 Disconnect the air supply before changing disc or pad.
15 Ensure the polisher has stopped rotating before putting it down or handling the pad or
disc.
16 EVER carry the polisher by the air hose.
17 EVER point the polisher at other persons.
18 EVER operate the polisher whilst under the influence or drugs, alcohol or intoxicating
medication.
19 Check you have no loose clothing, hair, jewellery or any other items of a personal nature
that might become entangled with the rotating parts.
20 Check you have a maximum inlet air pressure of 90PSI/6.3BAR.
PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
FT900_Product Instructions 09/10/2014 08:07 Page 3

FT900
Instruc%on Manual
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
Fig. 1
Air Fil er/Regula or
/Lubrica or
Whip
Hose
Airline
Air Fi ing
Quick Release Air Coupling
To Air Tool
Fig. 2
We recommend that your air tool is connected to the
main airline in the way displayed in Fig. 2.
1: Air Tool
2: Whip Hose/Leader Hose
3: Air Fitting
4: Quick Coupling
5: Main Air Hose
5
1
4
3
2
Air
Source
Familiarise Yourself with the Controls
1 The throttle is pressure sensitive.
Applying pressure will increase
rotational speed.
2 Removal of all pressure will stop the
machine.
3 Some models are fitted with a safety
lock to prevent accidental starting. IF
FITTED, this should be locked at all
times when the polisher is left under
power.
4 ever leave the tool unattended and
connected to the power supply.
During Use
1 When using the polisher for long periods of time, check the polishing pad for wear.
2 Replace worn pads as worn or clogged pads will make the polisher inefficient.
3 The polishing operation will cause heat. Check the material that is being worked on that
it is not getting too hot. If this is occurring, stop polishing to allow the material to cool
down.
4 You can adjust the speed of the tool by adjusting the pressure you apply to the throttle.
5 Make regular checks on the polishing pad for wear and damage and replace them
immediately.
6 Due to the potential heat caused by the polishing process, keep flammable liquids and
gases well away from the work area.
Installation
1 Check the tool over to make sure no part is missing or damaged.
2 Fitting an Air Filter, Regulator and Lubricator is recommended.
3 Refer to Fig. 1 for the recommended airline setup.
Pad
Trigger
Exhaust
Air Inlet
Handle
Air Flow Adjuster
FT900_Product Instructions 09/10/2014 08:07 Page 4

PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
4 It is strongly advised that you always use a Whip Hose/Leader Hose in combination with
Quick Release Couplings. See Fig. 2 for recommended setup.
5 Water in the air supply will cause the internal bearing of the tool to rust and eventually
seize.
6 Make sure that your airline is free from water at all times.
7 Always select the correct polishing pad grit for the job.
Tools Included with your Polisher
1 x High Flow Male Air Fitting
1 x Spanner
1 x Oil Pot
Maintenance
1 If the air supply is not lubricated sufficiently it will be necessary to lubricate the tool
directly. This can be done by disconnecting the air hose and pouring in 5ml of air tool oil
into the Air Inlet. Read safety data sheet or instructions on use of oil to ensure safe
usage. These can be obtained from your supplier.
2 Replace worn or damaged parts using genuine parts only.
3 Store tool in a dry area, do not allow tool to be immerse in water or used/stored in wet
conditions.
FT900_Product Instructions 09/10/2014 08:07 Page 5

FT900
Instruc%on Manual
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
o. Code Description Q’ty
1 FT900/1 Cap 1
2 FT900/2 O-Ring 1
3 FT900/3 Ball Bearing 1
4 FT900/4 Rear End Plate 1
5 FT900/5 Rotor 1
6 FT900/6 Rotor Bakelite 5
7 FT900/7 O-Ring 1
8 FT900/8 Cylinder 1
8-1 FT900/8-1 Spring Pin 1
9 FT900/9 Front End Plate 1
10 FT900/10 Ball Bearing 1
11 FT900/11 Ball Bearing 1
12 FT900/12 Plate Gear 2
12-1 FT900/12-1 Ball Axle 2
13 FT900/13 Gear Case 1
13-1 FT900/13-1 Washer 1
14 FT900/14 Pin 1
15 FT900/15 Ball Bearing 1
16 FT900/16 Internal Gear 1
17 FT900/17 Clamp ut 1
18 FT900/18 Gear Shaft 1
19 FT900/19 Plug 1
20 FT900/20 O-Ring 1
21 FT900/21 Spring 1
22 FT900/22 Plastic Ball 1
23 FT900/23 Body 1
24 FT900/24 Copper Cover 1
25 FT900/25 Valve Spring 1
26 FT900/26 Spring Pin 1
27 FT900/27 Lever Assembly 1
o. Code Description Q’ty
28 FT900/28 Regulator Assembly 1
29 FT900/29 Exhaust Plate 1
30 FT900/30 Exhaust 1
30-1 FT900/30-1 Screw 1
31 FT900/31 Rubber Sleave 1
32 FT900/32 17mm Spanner 1
Parts Diagram
FT900 75mm Air Polisher
FT900_Product Instructions 09/10/2014 08:07 Page 6

PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
Warranty
We hope that you will be very happy with your purchase. If you do have a problem with your tool,
you have the added peace of mind of a 6 month warranty, which comes into date from the date of
purchase (proof of purchase required).
Scope of Warranty
- The warranty will cover you from all faults caused by defective components or poor workmanship.
- Tools sent outside the EU are not covered by this warranty.
- Product must be returned to us, the warranty does not cover cost of carriage.
- If the product is no longer in manufacture, it will be replaced with a tool of equivalent or higher
specification.
What is not covered
- ormal wear and tear caused by use in accordance with the operating instructions.
- Replacement of any provided accessories, such as Backing Pads, Airline Connections, Air
Fittings, Blades, Spanners, etc.
- Accidental damage, faults caused by negligent use or care, neglect, misuse or careless operation,
handling and storage of the product.
- Modification of, or change of, any part of this product in any way.
- Faults caused by use of non compatible accessories.
- Tool seizure caused by insufficient oiling.
- Faults caused by incorrect installation.
- Repairs or alterations carried out by non-approved parties.
- Traces of water or rust inside tool - this shows that a properly working air filter has not been used.
Validity
- This warranty is valid for 6 months after date of purchase.
- Warranty is rendered invalid if;
- Tool is taken apart for any reason without our consent.
- Tool is not oiled daily.
- Air supply line is not used with a properly working air filter.
- A warranty claim will not be accepted without an official proof of purchase from your supplier.
Warranty Verification
Please keep this manual with your tool for the purpose of verifying your
warranty. Fill in box below to validate warranty.
Fax to 01582 667100
Tool Code: FT900
Place of Purchase
____________________________________________
____________________________________________
_____________ Post Code __________________
Date
___________________________________________
Your Details
Company ________________________
Address ________________________
________________________________
Post Code________
Email ________________________
FT900_Product Instructions 09/10/2014 08:07 Page 7

FT900
Instruc%on Manual
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
www.fastmovertoolsuk.com
Declaration of Conformity
We declare that the equipment detail below, to the best of our knowledge and
ability, complies with the following Directive.
Machinery Directive - 2006/42/EC and amending Directives
Equipment Description Air Operated 75mm Polisher in Kit
Part Code FT900
Distributed in the EU by Fast Mover Tools Ltd
Address Unit 1 Frenchs Avenue
Dunstable
Bedfordshire
LU6 1BH
United Kingdom
The following Transposed Harmonised Standards have been applied in the
design and construction of this equipment:
E ISO 28927-2:2009 Hand-held portable power tools - Test methods for evaluation of
vibration emission - Part 2: Wrenches, nutrunners and screwdrivers
E ISO 15744:2008 Hand-held non-electric power tools. oise measurement code.
Engineering method (grade 2)
E ISO 11148-8:2011 Hand-held non-electric power tools. Safety requirements. Sanders
and polishers
The manufacturer and the distributor, stated above, hold the Technical Construction File for this
equipment.
Signed on behalf of the distributor
(the responsible person) …………………………………………
ame: Brian Moffitt
Position: Director
Date and Place: 26/09/2012, Dunstable, UK
Please look after the environment, dispose of all packaging in a responsible way.
Always dispose of tools in accordance with local authority guidelines.
© 2014 Fast Mover Tools Ltd. This document is copyright and is not to be copied, circulated, distributed or shown
to anyone other than the intended recipient without the express permission of the Directors.
FT900_Product Instructions 09/10/2014 08:07 Page 8