FastCap BEST FENCE PRO V6 User manual

BEST FENCE PRO V6
INSTRUCTION MANUAL
SOME FEATURES AND ACCESSORIES MAY NOT BE INCLUDED WITH YOUR
SYSTEM. PLEASE VISIT WWW.FASTCAP.COM FOR MORE DETAILS.
FOR ALL BEST FENCE PRO SYSTEMS
APRIL 2021
FastCap, LLC
5016 Pacific Highway
Ferndale, WA 98248
Toll Free: 1-888-443-3748
Phone: [phone]
Fax: [phone]
Web: www.fastcap.com
Email: [email protected]

SOME FEATURES AND ACCESSORIES MAY NOT BE INCLUDED WITH YOUR SYSTEM.
PLEASE VISIT WWW.FASTCAP.COM FOR MORE DETAILS.
1
RELEASE LEGS BY PULLING HANDLES
ON BOTH SIDES
MAKE SURE BALL DETENT IS LOCKED
IN STANDING POSITION
STEP 2
STEP 4
WHEEL STAND TO DESIRED LOCATION
USING HANDLE
STEP 1
LIFT SINGLE WHEEL SIDE FIRST AND
PULL LEGS OUT.
THE HIGHER YOU LIFT THE EASIER.
REPEAT ON OTHER SIDE TO FINISH
STAND SETUP
STEP 3
STEP 5
WHEN FOLDING BACK UP, LIFT & FOLD
THE 2-WHEEL SIDE FIRST
STEP 6
BEST FENCE PRO STAND SETUP
SOME FEATURES AND ACCESSORIES MAY NOT BE INCLUDED WITH YOUR SYSTEM.
PLEASE VISIT WWW.FASTCAP.COM FOR MORE DETAILS.

SOME FEATURES AND ACCESSORIES MAY NOT BE INCLUDED WITH YOUR SYSTEM.
PLEASE VISIT WWW.FASTCAP.COM FOR MORE DETAILS.
2
ALLOW ENOUGH SPACING FOR RACK
WHEN APPLICABLE.
USE PROPELLER NUTS TO PUT SAW IN
BEST POSITION
PLACE SAW ON RAILS, WAIT TO
SCREW DOWN UNTIL FENCES ARE
ALIGNED (PG. 3 & 4)
STEP 3
ROTATE BRACKET 90º AND TIGHTEN
KNOB TO LOCK IN PLACE
STEP 2
POSITION SAW MOUNT ON RAILS
WITH PLASTIC BRACKET PARALLEL
STEP 1
(FOUND IN HARDWARE KIT)
MOUNT SAW WITH PROVIDED POWERHEAD SCREWS
STEP 4
BEST FENCE PRO SAW SETUP
FRONT
MIDDLE
PLACEMENT POSITIONS
BACK

SOME FEATURES AND ACCESSORIES MAY NOT BE INCLUDED WITH YOUR SYSTEM.
PLEASE VISIT WWW.FASTCAP.COM FOR MORE DETAILS.
3
ALIGN HOLE ON FENCE WITH LINE ON
PRECISION ADJUSTMENT BLOCK AND
INSERT PIN TO LOCK IN PLACE
SIDE KNOB FRO HORIZONTAL
ADJUSTMENTS
STEP 3
STEP 5
PLACE FENCE ON PRECISION
ADJUSTMENT BLOCKS BY HOOKING
THE BACKSIDE FIRST
STEP 2
LOOSEN KNOBS AND PULL OUT ARMS
FROM STAND. TIGHTEN KNOBS.
STEP 1
USE LEVEL TO ALIGN FENCE WITH SAW.
ONCE ALIGNED, SCREW DOWN SAW.
BOTTOM KNOB FOR
HEIGHT ADJUSTMENT
STEP 4
STEP 6
BEST FENCE PRO FENCE SETUP

SOME FEATURES AND ACCESSORIES MAY NOT BE INCLUDED WITH YOUR SYSTEM.
PLEASE VISIT WWW.FASTCAP.COM FOR MORE DETAILS.
4
TIGHTEN ADJUSTMENT KNOB TO LOCK
BLOCK IN PLACE
STEP 3
LOOSEN AND HOLD ASSEMBLY WHILE
ROTATING BOTTOM BRACKET 90º
STEP 2
POSITION BLOCK ON RAILS WITH
BOTTOM BRACKET PARALLEL
STEP 1
BEST FENCE PRO BLOCK ALIGNMENT
TROUBLESHOOTING
IF THERE IS EXCESS MOVEMENT IN THE PRECISION ADJUSTMENT BLOCK
TIGHTEN THE ALLEN SCREWS
FOR VIDEO INSTRUCTIONS ON
CONVERTERING PABS TO A BEST
FENCE PRO SYSTEM
STEP 4

SOME FEATURES AND ACCESSORIES MAY NOT BE INCLUDED WITH YOUR SYSTEM.
PLEASE VISIT WWW.FASTCAP.COM FOR MORE DETAILS.
5
POSITION FENCE ONTO MALE-MALE
CONNECTOR AND USE ATTACHED PIN TO
SECURE IN PLACE
REPEAT STEP 1 - 4 ON SECOND FENCE FOR VIDEO INSTRUCTIONS ON THE
FENCE CONNECTOR SET UP
STEP 3
STEP 5
POSITION UPPER HAND AND ATTACHED
SECOND FENCE
STEP 2
POSITION MALE-MALE CONNECTOR SO
THAT FENCE END IS ON MIDDLE LINE.
USE ATTACHED PIN TO SECURE IN PLACE.
STEP 1
USE THE PRECISION PUMP JACK TO
LEVEL FENCES
STEP 4
BEST FENCE MALE-MALE SETUP
STEP 6

SOME FEATURES AND ACCESSORIES MAY NOT BE INCLUDED WITH YOUR SYSTEM.
PLEASE VISIT WWW.FASTCAP.COM FOR MORE DETAILS.
6
STEP 1 STEP 2 STEP 3
SCAN FOR
VIDEO INST.
SLIDE BAG ONTO BAG RACK
*ONLY AVAILABLE FOR BEST FENCE 3 OR 4, BEST FENCE PRO 3 OR 4*
STEP 2
ATTACH BAG RACK BY SLIDING POST
INTO HOLE
*ONLY AVAILABLE FOR BEST FENCE 3 OR 4, BEST FENCE PRO 3 OR 4*
INSERT WORK TABLE INTO ACCESSORY
HOLE WHERE DESIRED & TIGHTEN KNOB
TO SECURE
*ONLY AVAILABLE FOR BEST FENCE 3 OR 4, BEST FENCE PRO 3 OR 4*
LUMBER RACKS CAN BE FOLDED
OPEN TO SUPPORT EXTRA LUMBER
STEP 1
OPTION 1
BEST FENCE PRO ACCESSORIES
OPTION 2
STEP 1: ATTACH ARM BY HOOKING REAR FIRST THEN TIGHTENING WEDGE KNOB
STEP 2: ADJUST L-BRACKET AND PLASTIC SLIDE TO FIT SIZE OF YOUR CROWN MOLDING
STEP 3: TO REMOVE ARM, SLIDE ALL PIECES OFF THE BEST FENCE. UNSCREW BOTTOM KNOB AND PUSH
UP TO RELEASE WEDGE FROM BEST FENCE.

SOME FEATURES AND ACCESSORIES MAY NOT BE INCLUDED WITH YOUR SYSTEM.
PLEASE VISIT WWW.FASTCAP.COM FOR MORE DETAILS.
7
STEP 4
STEP 2
INSTALL TOP PLATE INTO PRECISION
ADJUSTMENT BLOCKS
REMOVE FENCE AND UNSCREW TOP
PLATE FROM BLOCK WITH INCLUDED
WRENCH
STEP 3
STEP 1
INSTALL INCLUDED SPACERS
TO TOP PLATE
SOME SAWS HAVE HIGHER DECKS
REQUIRING SPACERS FOR PRECISION
ADJUSTMENT BLOCKS
BEST FENCE PRO BLOCK SPACER
TROUBLESHOOTING
IF THERE IS EXCESS MOVEMENT IN
THE PRECISION ADJUSTMENT BLOCK
TIGHTEN THE ALLEN SCREWS.
SEE PAGE 4 FOR MORE DETAIL
ADJUST SET SCREWS TO CHANGE
FORWARD/BACKWARD PITCH OF
PAB IF NECESSARY
PAB ADJUSTMENTS