Fastwel CPB8929 User manual



CPB8929
3.5” SBC
with Intel® Atom™ E620T 600 MHz
User Manual
Rev. 001
May 2013
The product described in this manual is compliant
with all related CE standards.

Product Title: CPB8929
Document name: CPB8929 User Manual
Manual version: 001
Copyright © 2013 Fastwel Co. Ltd. All rights reserved.
Revision Record
Rev.
Index Brief Description Product Index Date
001 Initial version CPB8929 May 2013
Contact Information
Fastwel Co. Ltd Fastwel Corporation US
Address: 108 Profsoyuznaya st.,
Moscow 117437,
Russian Federation
55 Washington St. #310
Brooklyn, New York 11201
USA
Tel.: [phone].554.3686
Fax: [phone].797.0600
Tollfree: 1.877.RURUGGED (787.8443)
Technical support 1.347.585.4505
E-mail: [email protected]
Web: http://www.fastwel.com/

  CPB8929

TableofContents
TableofContents ............................................................................................................................................................. 3
NotationConventions ...................................................................................................................................................... 5
GeneralSafetyPrecautions.............................................................................................................................................. 6
Unpacking,InspectionandHandling ............................................................................................................................... 7
Warranty.......................................................................................................................................................................... 8
Chapter1:ProductInformation .................................................................................................................................9
1.1BlockDiagram............................................................................................................................................................ 9
1.2KeyFeatures............................................................................................................................................................. 10
1.3BoardPlacement ..................................................................................................................................................... 11
1.4OnboardConnectorList ........................................................................................................................................... 12
1.5MechanicalDrawings .............................................................................................................................................. 13
1.6Packinglist............................................................................................................................................................... 13
Chapter2:JumpersandConnectors.........................................................................................................................14
2.1JumperSettings ....................................................................................................................................................... 14
JP2:ClearCMOS........................................................................................................................................................ 14
JP3:LCDBRIGHTNESSCONTROLMODESELECT ....................................................................................................... 14
JP4:LVDSVOLTAGESELECT ....................................................................................................................................... 15
JP5:AUDIOOUTPUTMODESELECT..........................................................................................................................15
JP6:AT/ATXMODESELECT...................................................................................................................................... 15
2.2OnboardConnectorPinAssignment........................................................................................................................ 16
CF1:CFSOCKET........................................................................................................................................................ 16
CN1:VGAconnector ................................................................................................................................................. 16
CN2:COMconnector ................................................................................................................................................ 16
CN4:USBConnector ................................................................................................................................................. 16
CN5:LPCConnector.................................................................................................................................................. 17
CN6/CN7:GigaLANRJ45connector ......................................................................................................................... 17
CN8:PowerSwitchpinheader ................................................................................................................................. 17
CN9:RESETPINHEADER ........................................................................................................................................... 17
CN10:CANBUSConnector ........................................................................................................................................ 17
CN11:SATAPOWERConnector................................................................................................................................. 18
CN12:GPIO ................................................................................................................................................................ 18
CN13/16/22:COMPORTConnector............................................................................................................................ 18
CN14:SATAConnector.............................................................................................................................................. 18
CN17:2WAUDIOOUTPUTPINHEADER................................................................................................................... 18
CN18:2WAUDIOOUTPUTPINHEADER................................................................................................................... 18
CN19:MINIPCIESOCKET .......................................................................................................................................... 19
CN15:MINIPCIELED ................................................................................................................................................ 19
CN20:BatteryConnector.......................................................................................................................................... 19
CN21:DCPOWERConnector.................................................................................................................................... 19
CN23:SPI .................................................................................................................................................................. 20
CN24:AUDIOConnector........................................................................................................................................... 20
CN25:LVDSconnector .............................................................................................................................................. 20
CN27:SMBUSconnector .......................................................................................................................................... 20
CN28:PANELINVERTERConnector........................................................................................................................... 20
Chapter3:GettingStarted .......................................................................................................................................21
CPB8929UserManual3©2013FastwelVer.001

  CPB8929

3.1InstallingtheCFcard ............................................................................................................................................... 21
3.2DisableEG20TGbEControllerinstruction................................................................................................................ 21
Chapter4:AMIBIOSUTILITY ...................................................................................................................................24
4.1Starting .................................................................................................................................................................... 24
4.2NavigationKeys ....................................................................................................................................................... 24
4.3MainMenu .............................................................................................................................................................. 25
4.4AdvancedMenu ....................................................................................................................................................... 26
4.4.1ACPISettings.................................................................................................................................................... 27
4.4.2CPUConfiguration............................................................................................................................................ 27
4.4.3USBConfiguration............................................................................................................................................ 28
4.4.4AHCISATAConfiguration.................................................................................................................................. 29
4.4.5OtherFunction................................................................................................................................................. 30
4.4.6SuperIOConfiguration .................................................................................................................................... 31
4.4.7H/WMonitor ................................................................................................................................................... 31
4.4.8SerialPortConsoleRedirection ....................................................................................................................... 32
4.5Chipset ..................................................................................................................................................................... 33
4.5.1NorthBridgeChipsetConfiguration................................................................................................................. 33
4.5.1SouthBridgeChipsetConfiguration................................................................................................................. 34
4.6Boot ......................................................................................................................................................................... 34
4.7Security .................................................................................................................................................................... 35
4.8Saveandexit............................................................................................................................................................ 36
AppendixA .............................................................................................................................................................38
SafetyInformation......................................................................................................................................................... 38
Electricalsafety.............................................................................................................................................................. 38
Operationsafety ............................................................................................................................................................ 38
All information in this document is provided for reference only, with no warranty of its suitability for any specific purpose. This information has been
thoroughly checked and is believed to be entirely reliable and consistent with the product that it describes. However, Fastwel accepts no responsibility
for inaccuracies, omissions or their consequences, as well as liability arising from the use or application of any product or example described in this
document.
Fastwel Co. Ltd. reserves the right to change, modify, and improve this document or the products described in it, at Fastwel's discretion without further
notice. Software described in this document is provided on an “as is” basis without warranty. Fastwel assumes no liability for consequential or
incidental damages originated by the use of this software.
This document contains information, which is property of Fastwel Co. Ltd. It is not allowed to reproduce it or transmit by any means, to translate the
document or to convert it to any electronic form in full or in parts without antecedent written approval of Fastwel Co. Ltd. or one of its officially
authorized agents.
Fastwel and Fastwel logo are trademarks owned by Fastwel Co. Ltd., Moscow, Russian Federation. CompactPCI is a trademark of the PCI industrial
Computers Manufacturers Group. Ethernet is a registered trademark of Xerox Corporation. IEEE is a registered trademark of the Institute of Electrical
and Electronics Engineers Inc. Intel is a trademark of Intel Corporation. Microsoft is a trademark of the Microsoft corporation. In addition, this document
may include names, company logos and trademarks, which are registered trademarks and, therefore, are property of their respective owners.
Fastwel welcomes suggestions, remarks and proposals regarding the form and the content of this Manual.
CPB8929UserManual4©2013FastwelVer.001

  CPB8929

NotationConventions

Warning, ESD Sensitive Device!
This symbol draws your attention to the information related to electro static sensitivity
of your product and its components. To keep product safety and operability it is
necessary to handle it with care and follow the ESD safety directions.
Warning!
This sign marks warnings about hot surfaces. The surface of the heatsink and some
components can get very hot during operation. Take due care when handling, avoid
touching hot surfaces!
Caution: Electric Shock!
This symbol warns about danger of electrical shock (> 60 V) when touching products
or parts of them. Failure to observe the indicated precautions and directions may
expose your life to danger and may lead to damage to your product.
Warning!
Information marked by this symbol is essential for human and equipment safety.
Read this information attentively, be watchful.
Note...
This symbol and title marks important information to be read attentively for your own
benefit.

CPB8929UserManual5©2013FastwelVer.001

  CPB8929

GeneralSafetyPrecautions
This product was developed for fault-free operation. Its design provides conformance to all related safety
requirements. However, the life of this product can be seriously shortened by improper handling and incorrect
operation. That is why it is necessary to follow general safety and operational instructions below.
Warning!
All operations on this device must be carried out by sufficiently skilled
personnel only.
Warning!
When handling this product, special care must be taken not to hit
the heatsink (if installed) against another rigid object. Also, be careful not to
drop the product, since this may cause damage
to the heatsink, CPU or other sensitive components as well.
Please, keep in mind that any physical damage to this product
is not covered under warranty.
Note:
This product is guaranteed to operate within the published temperature
ranges and relevant conditions. However, prolonged operation near the
maximum temperature is not recommended by Fastwel or by electronic
chip manufacturers due to thermal stress related failure mechanisms.
These mechanisms are common to all silicon devices, they can reduce the
MTBF of the product by increasing the failure probability. Prolonged
operation at the lower limits of the temperature ranges has no limitations.
Caution, Electric Shock!
Before installing this product into a system and before installing other
devices on it, always ensure that your mains power is switched off.
Always disconnect external power supply cables during all handling and
maintenance operations with this module to avoid serious danger of
electrical shock.
CPB8929UserManual6©2013FastwelVer.001

  CPB8929

Unpacking,InspectionandHandling
Please read the manual carefully before unpacking the module or mounting the device into your system. Keep
in mind the following:
ESD Sensitive Device!
Electronic modules and their components are sensitive to static electricity.
Even a non-perceptible by human being static discharge can be sufficient
to destroy or degrade a component's operation! Therefore, all handling
operations and inspections of this product must be performed with due
care, in order to keep product integrity and operability:
Preferably, unpack or pack this product only at EOS/ESD safe workplaces. Otherwise, it is
important to be electrically discharged before touching the product. This can be done by touching
a metal part of your system case with your hand or tool. It is particularly important
to observe anti-static precautions when setting jumpers or replacing components.
If the product contains batteries for RTC or memory back-up, ensure that the module is not
placed on conductive surfaces, including anti-static mats or sponges. This can cause short-circuit
and result in damage to the battery and other components.
Store this product in its protective packaging while it is not used for operational purposes.
Unpacking
The product is carefully packed in an antistatic bag and in a carton box to protect it against possible damage
and harmful influence during shipping. Unpack the product indoors only at a temperature not less than +15°C
and relative humidity not more than 70%. Please note, that if the product was exposed to the temperatures
below 0°Сfor a long time, it is necessary to keep it at normal conditions for at least 24 hours before
unpacking. Do not keep the product close to a heat source.
Following ESD precautions, carefully take the product out of the shipping carton box. Proper handling of the
product is critical to ensure correct operation and long-term reliability. When unpacking the product, and
whenever handling it thereafter, be sure to hold the module preferably by the front panel, card edges or
ejector handles. Avoid touching the components and connectors.
Retain all original packaging at least until the warranty period is over. You may need it for shipments or for
storage of the product.
Initial Inspection
Although the product is carefully packaged, it is still possible that shipping damages may occur. Careful
inspection of the shipping carton can reveal evidence of damage or rough handling. Should you notice that
the package is damaged, please notify the shipping service and the manufacturer as soon as possible. Retain
the damaged packing material for inspection.
After unpacking the product, you should inspect it for visible damage that could have occurred during shipping
or unpacking. If damage is observed (usually in the form of bent component leads or loose socketed
components), contact Fastwel's official distributor from which you have purchased the product for additional
instructions. Depending on the severity of the damage, the product may even need to be returned to the
factory for repair. DO NOT apply power to the product if it has visible damage. Doing so may cause further,
possibly irreparable damage, as well as result in a fire or electric shock hazard.
If the product contains socketed components, they should be inspected to make sure they are seated fully in
their sockets.
CPB8929UserManual7©2013FastwelVer.001

  CPB8929

Handling
In performing all necessary installation and application operations, please follow only the instructions supplied
by the present manual.
In order to keep Fastwel’s warranty, you must not change or modify this product in any way, other than
specifically approved by Fastwel or described in this manual.
Technical characteristics of the systems in which this product is installed, such as operating temperature
ranges and power supply parameters, should conform to the requirements stated by this document.
Retain all the original packaging, you will need it to pack the product for shipping in warranty cases or for safe
storage. Please, pack the product for transportation in the way it was packed by the supplier.
When handling the product, please, remember that the module, its components and connectors require
delicate care. Always keep in mind the ESD sensitivity of the product.
Warranty
1. Warranty period
Fastwel Co. Ltd. (Fastwel) endeavors to offer customers the most comprehensive post-sales services and
protection, offering a 1 year warranty to standard Fastwel products. Within the warranty period, customers are
entitled to receive comprehensive and prompt repair and warranty.
Standard products manufactured by Fastwel are offered a warranty of 1 year, from the date of delivery from
Fastwel. For non-Fastwel products, the product warranty and repair time shall be based on the service
standards provided by the original manufacturer; in principle Fastwel will provide a warranty service for no
more than one year over these products.
2. Maintenance service within the warranty period
In the case of a DOA (Defect-on-Arrival) of a Fastwel product where the customer finds any defect within 1
month after the delivery, Fastwel will replace it with a new product in a soonest way to fulfill our
responsibilities. For the returned defective new product, it is necessary to verify that there shall be no bruise,
alteration, scratch or marking to the appearance, and that none of the delivered accessories is missing;
otherwise, the customer will be requested to pay a partial processing fee. On the other hand, if the new
product defect is resulting from incorrect configuration or erroneous use by the user instead of any problem of
the hardware itself, the customer will also be requested to pay for relevant handling fees.
As for other conditions, Fastwel will handle defects by way of repair. The customer will be requested to send
the defective product to a Fastwel authorized service center, and Fastwel will return the repaired product back
to the customer as soon as possible.
3. Ruling of an out-of-warranty defect
The following situations are not included in the warranty:
The warranty period has expired.
Product has been altered or its label of serial number has been destroyed or torn off.
Product functionality issues resulting from improper use by the user, unauthorized dismantle or
alteration, unfit operation environment, improper maintenance, accident or other causes. Fastwel
reserves the right for the ruling of the aforementioned situations.
Product damage resulting from fire, lightening, floods, earthquakes or other calamity.
The ruling of warranty of non-Fastwel products and accessories shall be in accordance with standards
set up by the original manufacturer. These products and accessories include RAM, HDD, FDD, CD-
ROM, CPU, FAN, etc.
Product upgrade request or test request submitted by the customer after expiration of warranty.
For further questions, please e-mail to our support staff: [email protected].
CPB8929UserManual8©2013FastwelVer.001

Product Information  CPB8929


Chapter1:ProductInformation

1.1BlockDiagram




CPB8929UserManual9©2013FastwelVer.001

Product Information  CPB8929

1.2KeyFeatures
Processor&System
CPUTypeIntel®Atom™E620T600MHz
ChipsetIntel®TopcliffEG20T
MemoryType512MBDDR2667/800MHzMemoryIConboard
BIOSAMI™BIOS
SuperI/OSMSCSCH3114
Watchdog1‐255sec.or1‐255min.softwareprogrammable,
cangeneratesystemreset
ExpansionSlot
1xMiniPCIeslot(half‐size)
Display
ChipsetChrontel7317BSDVOtoVGATransmitter
VGAYes(Max.resoultion1280x1024@70Hz)
LVDSSupportssignlechannel18/24‐bitLVDS
DualIndependent
DisplaysCapability
LVDS+VGA
Audio
CodecRealtekALC886HighDefinitionAudioCodec
*2Wamplifieronboard
Ethernet
Chipset2xIntel®82574ITGbELAN
WOLYes
BootfromLANYesforPXE
RearI/O
VGA1
Ethernet2xRJ45
USB2
COM1xR S 2 3 2/4 2 2/4 8 5 with5V/12Vselection
PowerButtonOptional
InternalI/O
SATA1xSATAII(3Gb/s)
1x3pinpowerconnector
SSD1xCompactFlashTypeIISocket
USB2portsonrearI/O
COM4xCOMports
yCOM1portsupportsRS232/422/485with5V/12V
selectiononrearI/O
yCom2~4portssupportsRS232by1x10pinheader
LVDSConnector 20pinconnector
DIO4in/4out
CANBus1x10pinheader
SMBus1x2pinheader
Audio1x6pinheaderforMic‐in/Lin‐in/Lin‐out
MechanicalandEnvironment
FormFactor3.5”SBC
CPB8929UserManual10©2013FastwelVer.001

Product Information  CPB8929

PowerType12VDC‐in,4pinATXpowerconnectorAT/ATX
modesupport(optionalforscrewtypeDCjack)
Dimension146x102mm(5.7"x4")
OperatingTemp.‐40°Cto85°C
StorageTemp.‐40°Cto85°C
Relativehumidity10%to90%,non‐condensing
*Allspecificationsandphotosaresubjecttochangewithoutnotice*


1.3BoardPlacement



CPB8929UserManual11©2013FastwelVer.001

Product Information  CPB8929

1.4OnboardConnectorList
ConnectorFunction
CN1VGA
CN2COM1
CN4USB
CN5Port80
CN6LAN
CN7LAN
CN8POWERSWITCHPINHEADER
CN9RESET
CN10CANBUS
CN11HDDPOWERCONNECTOR
CN12DIO
CN13COM4
CN14SATA
CN15WLAN_LED
CN16COM3
CN17AMP_R
CN18AMP_L
CN19MINIPCIE
CN20BATTERYCONNECTOR
CN21POWERCONNECTOR
CN22COM2
CN23SPI
CN24AUDIO
CN25LVDS
CN27SMBUSCONNECTOR
CN28PanelInverterConnector
CF1CFCONNECTOR

CPB8929UserManual12©2013FastwelVer.001

Product Information  CPB8929

1.5MechanicalDrawings


1.6Packinglist

1xCPB89293.5”SBC
1xDriverDVD
Boardisdeliveredwithoutheatsink–customcoolingsolutionisrequired.
Additionalaccessoriesandcables:ACS80005–cablekitforCPB8928/CPB8929

Warning!!!
Ifanyoftheaboveitemsisdamagedormissing,pleasecontactyour
localdistributor.

CPB8929UserManual13©2013FastwelVer.001

Jumpers and Connectors   CPB8929

Chapter2:JumpersandConnectors

2.1JumperSettings




JP2:ClearCMOS
PinSetting 
1‐2Normal
(Default)

2‐3CLEARCMOS


JP3:LCDBRIGHTNESSCONTROLMODESELECT
PinSetting 
1‐2DCMODE

2‐3PWMMODE
(Default)


CPB8929UserManual14©2013FastwelVer.001

Jumpers and Connectors   CPB8929

JP4:LVDSVOLTAGESELECT
PinSetting 
1‐2+3.3V
(Default)

2‐3+5V


JP5:AUDIOOUTPUTMODESELECT
PinSetting 
1‐2SEOutputMode
2‐3BTLMode
(Default)


JP6:AT/ATXMODESELECT
PinSetting 
1‐2ATXMode
(Default)

2‐3ATMode




CPB8929UserManual15©2013FastwelVer.001

Jumpers and Connectors   CPB8929

2.2OnboardConnectorPinAssignment

CF1:CFSOCKET
PinDefinePinDefinePinDefine PinDefinePinDefine
1GND11GND21D0031D1541RESET
2D0312GND22D0132CS42IORDY
3D0413VCC23D0233NC43DREG
4D0514GND24WP34IOR44DACK
5D0615GND25NC35IOW45LED
6D0716GND26CD36WE46BVD
7CS17GND27D1137RDY/BSY 47D08
8GND18A0228D1238VCC48D09
9GND19A0129D1339SCSE49D10
10GND20A0030D1440NC50GND

CN1:VGAconnector
PinDefinePinDefine
1Red2Green
3Blue4N.C.
5GND6GND
7GND8GND
9PWR10GND
11N.C.12DDCSDA
13HSYNC14VSYNC
15DDCSCL 


[[[[ 
CN2:COMconnector
PinDefinePinDefine
1DCD#2RXD#
3TXD#4DTR#
5GND6DSR#
7RTS#8CTS#
9RI# 


CN4:USBConnector
PinDefinePinDefine
1+5V2DATA0‐
3DATA0+4GND
5+5V6DATA1‐
7DATA1+8GND


CPB8929UserManual16©2013FastwelVer.001

Jumpers and Connectors   CPB8929

CN5:LPCConnector
PinDefinePinDefine
1+3.3V2AD0
3AD14AD2
5AD36Frame#
7PCIERST#8+5V
9CLOCK10
11GND12GND


CN6/CN7:GigaLANRJ45connector
PinDefineLED
1MDI0+D2:Link/ActivityLED
2MDI0‐ LinkGreen
3MDI1+ActivityBlinking
4MDI2+
5MDI2‐ D1:Bi‐ColorSpeedLED
6MDI1‐ 10MbpsOff
7MDI3+100MbpsYellow
8MDI3‐


1000Mbps Green

CN8:PowerSwitchpinheader
PinDefine
1PW_SW
2GND



CN9:RESETPINHEADER
PinDefine
1RESET
2GND



CN10:CANBUSConnector
PinDefine
1GND
2CAN_L
3CAN_H
4CAN_GND
5NC
6NC
7+5V
8NC
9NC
10NC

 

CPB8929UserManual17©2013FastwelVer.001

Jumpers and Connectors   CPB8929

CN11:SATAPOWERConnector
PinDefine
1GND
2+12V
3+5V

CN12:GPIO
PinDefinePinDefine
1GPI2GPO
3GPI4GPO
5GPI6GPO
7GPI8GPO
9+5V10GND



CN13/16/22:COMPORTConnector
PinDefine
1DCD#
2DSR#
3RXD#
4RTS#
5TXD
6CTS##
7DTR#
8RI#
9GND
10+5V

 

CN14:SATAConnector
PinDefine
1GND
2TXP
3TXN
4GND
5RXN
6RXP
7GND


CN17:2WAUDIOOUTPUTPINHEADER
PinDefine
1RIGHT+
2RIGHT‐



CN18:2WAUDIOOUTPUTPINHEADER
PinDefine
1LEFT+
2LEFT‐


CPB8929UserManual18©2013FastwelVer.001

Jumpers and Connectors   CPB8929


CN19:MINIPCIESOCKET
PinDefinePinDefine
1WAKE#2+3.3V
3Reserved4GND
5Reserved6+1.5V
7CLKREQ#8Reserved
9GND10Reserved
11REFCLK‐ 12Reserved
13REFCLK+14Reserved
15GND16Reserved
17Reserved18GND
19Reserved20Reserved
21GND22PERST#
23PERN024+3.3VAUX
25PERP026GND
27GND28+1.5V
29GND30SMB_CLK
31PETN032SMB_DATA
33PETP034GND
35GND36USB_D‐
37Reserved38USB_D+
39Reserved40GND
41Reserved42LED_WWAN#
43Reserved44LED_WLAN#
45Reserved46LED_WPAN#
47Reserved48+1.5V
49Reserved50GND
51Reserved52+3.3V

CN15:MINIPCIELED
PinDefine
1+3.3V
2LED_WLAN#



CN20:BatteryConnector
PinDefine
1+3.3V
2GND



CN21:DCPOWERConnector
PinDefine
1GND
2GND
3+12V
4+12V
CPB8929UserManual19©2013FastwelVer.001

Jumpers and Connectors   CPB8929


CN23:SPI
PinDefinePinDefine
1VCC3_SPI2GND
3SPI_CS_N4SPI_CLK
5SPI_MISO6SPI_MOSI
78FLASH_IO


CN24:AUDIOConnector
PinDefine
1SPKR_R
2GND
3SPKR_L
4LINE_IN_R
5MIC_IN
6LINE_IN_L





CN25:LVDSconnector
PinDefinePinDefine
1TX0+2TX0‐
3GND4GND
5TX1+6TX1‐
7GND8VCC_LCD
9TX2+10TX2‐
11TXC+12TXC‐
13GND14GND
15TX3+16TX3‐
17ENABKL18VCC_LCD
19I2C_DAT20I2C_CLK





CN27:SMBUSconnector
PinDefine
1SMB_DATA
2SMB_CLK



CN28:PANELINVERTERConnector
PinDefine
1+12V
2GND
3BacklightEnable
4BrightnessControl
5+5V

CPB8929UserManual20©2013FastwelVer.001