Fat Cat POKEY 64-1000 Product information sheet

Easy
Assembly
Instructions
DO NOT RETURN TO STORE
For all returns and warranty coverage, please call:
GLD Products
1-800-225-7593
Please provide model number, serial number and/or part
number when you call. Numbers can be found on outside
of packaging.
PRO GAME TABLES
Model # 64-1000 & 64-1002

2
Congratulations on your purchase of the Fat Cat™Pockey™
2 in 1 Gametable!
This manual is to instruct you during the assembly of your new
table. Four people required for some steps.
Careful handling of all parts during assembly will ensure many
years of enjoyment!
WARNING: Changing of game should be done under
adult supervision.
Rotating table may pose a finger pinching hazard for young
children. Please exercise caution.
Never open fan compartment while fan is running. To do so
may cause serious injury.
Careful handling of all parts during assembly will ensure many years
of enjoyment!
Arrange all of your tools before you begin assembly.
Tools
Assembly of the Pockey™2 in 1 Gametable requires the
following common tools:
• Phillips screwdriver
• Wrench (included)
• Level
HPRO TIP H

3
STEP 2. Assembling pedestals.
Insert pedestals into bases as shown, and secure each with four (#5) 11 /2"
flat head screws.
Assembling Your
Pockey™2 in 1 Gametable
STEP 1. Assembling bases.
Carefully remove two (#15) pedestals, two (#16) pedestal supports, four
(#13) levelers and eight (#5) 11
/2" flat head screws from packaging. Insert
levelers into pre-drilled holes in bottom of bases and secure part way.
16
Bevel faces
the outside
Wider side
to the inside
of the table
13
5
Outside
15

4
8
2
14
17
17
Step 3. Attaching L-supports and hinges.
Place the female (#8 & #14) hinges in the precut slots on the edge of each
pedestal using (#2) 1
/2" round head screws. Attach male (#8 & #14) hinges
in the precut slots on the edge of each (#17) L-support and secure using
(#2) screws. Attach L-support to pedestal using the hinges.

5
19
19
20
21
22
1
18
STEP 4. Assembling ball storage trays.
Each tray consists of a (#18) bottom panel, an (#20) outside rail, a (#21)
inside rail, two (#19) end pieces and (#22) 3 bottom supports. With (#1)
1" flat head screws, secure (#20) outside and (#21) inside rails to one of the
(#19) end panels. Slide the (#18) bottom panel into precut slot and snap
on other (#19) end panel. Secure with (#1) 1" flat head screws. Flip storage
tray upside-down. Place 3 (#22) bottom supports into cutouts, and secure
with (#1) 1" flat head screws. Repeat for the other tray.

6
4
3
STEP 6. Assembling the cabinet.
With the help of another person, loosely attach the ball storage trays
(making sure the outside rails face out) to both pedestals with (#4) 5/
16"
washers and (#3) 5/16 x 11
/2" hex bolts. Lock L-supports to ball storage
trays by pressing hard on the L-support. With L-supports in lock position,
finish tightening screws. Adjust screws to make sure L-supports lock and
unlock easily.
STEP 5. Installing L-support locks.
Insert (#9) lock bolts into
predrilled holes into the outside
rail of ball storage trays. Place
(#10) washer, (#12) spring washer
and (#11) hex nut over threaded
end and tighten.
12
9
11
10
11
10
12

7
Step 7. Attaching rotating table top.
Place a (#6) 20mm hex nut and two (#7)
washers over each threaded shank on
the non-powercord end of the (#23)
table top and tighten. The hex nut and
washers have been pre-assembled on
the end with the power cord. With the
help of three other people, lift the table
top and rest it in the center groove on
the top of each pedestal.
6
77
6
7

8
67
STEP 8.
Securing table top.
Thread (#7) washer and (#6)
hex nuts over the ends of the
threaded shanks.
STEP 9. Securing table top.
Using the (#28) wrench, tighten (#6) hex nuts TOWARD pedestals. Make
sure the distance between table top and hex nut are equal on both ends
of table. Adjust as necessary. Rotate table a few times and continue to
tighten until the threaded shank stops rotating.
Equal distance between
the table and pedestal
on both ends of table Table edge
Pedestal
Pedestal edge

9
STEP 10. Attaching puck catchers.
Align (#24) puck catcher with predrilled holes on each end of playing
table and secure to pedestal with (#2) 1/2" round head screws. Run the
power cord through the puck catcher.
STEP 11. Adjusting levelers.
With the help of another person, turn
each leveler until table rests level to the
floor. Check with a level placed cross-
wise and length-wise on table top. Re-
adjust levelers as necessary. Remove
and discard sticky backer from (#26)
goalie felt sticker and apply to (#25)
goalie.
You are now ready to play!
Adhere the 
sticky side
of felt to 
the bottom 
of goalie.
Peel backing 
off felt to 
expose 
adhesive.
25
26
224
2

10
Pockey™2 in 1 Gametable Parts List
1" Flat Head Screw
28 pieces
1
/
2"Round Head
Screw - 40 pieces
11
/
2"Flat Head
Screw - 8 pieces
Lock Bolt
4 pieces
3/8" Washer
4 pieces
Spring Washer
4 pieces
20mm Hex Nut
4 pieces
20mm"Washer
6 pieces
Right Hinge
4 pieces
5
/
16" x 11
/
2"Hex Bolts
8 pieces
5
/
16"Washer
8 pieces
#1. #2. #3. #4.
#5. #6. #7. #8.
#9. #10.
5
/
16"Hex Nut
4 pieces
#11. #12.
Leveler
4 pieces
Hinge
4 pieces
Pedestal
2 pieces
Pedestal Support
2 pieces
#13. #14. #15. #16.

11
Pockey™2 in 1 Gametable Parts List
(continued)
L- Support
4 pieces
Inside Rail
2 pieces
Goalie
2 pieces
Goalie Felt Sticker
2 pieces
Wrench
2 pieces
Round Puck
1 piece
Bottom Supports
6 pieces
Table Top
1 piece
Puck Catcher
2 pieces
Ball Storage Tray -
Bottom - 2 pieces
Ball Storage Tray -
End Piece - 4 pieces
Outside Rail
2 pieces
#17. #18. #19. #20.
#21. #22. #23.
#25. #26. #27. #28.
Billiard Balls
1 set
Brush
1 piece
Chalk
2 pieces
Triangle
1 piece
#29.
2 Cue Sticks
4 pieces
#33.
#30. #31. #32.
#24.

WARRANTY INFORMATION
90-Day Warranty on Pockey™ Table
Manufacturer warrants to the original retail purchaser,
this product to be free from defects in material and
workmanship for a period of ninety (90) days from the
date of purchase.
Should this product become defective due to material or
workmanship within the warranty period, contact our
Customer Service Department. This warranty is not
transferable and does not cover normal wear and tear,
or damage caused by improper handling, installation or
use of this product. This warranty is also void if product is
in any way abused, damaged, or modified from its
original state, or if used for other than indoor residential
use. This warranty gives you specific legal rights, and you
may have other rights which vary from state to state.
PRO GAME TABLES
GLD Products
S84 W19093 Enterprise Drive
Muskego, WI 53150 USA
800 225 7593 • FAX [phone]
Web Site: www.gldmfg.com
Email: [email protected]
DO NOT RETURN TO STORE
For all returns and warranty coverage, please visit our
website at www.gldmfg.com or call 1-800-225-7593.
Please provide model number, serial number and/or part
number when you call. Numbers can be found on outside
of packaging.