Fat Cat 64-0500 Product information sheet

Easy Assembly
Instructions & Rules
TM
Model # 64-0500
DO NOT RETURN TO STORE.
FOR ALL RETURNS AND WARRANTY
COVERAGE PLEASE CALL GLD
PRODUCTS:
1-800-225-7593
Please provide model number, serial
number, and/or part number of the
product or part when you call.
Numbers can be found on outside
of packaging.
Featuring The
Leveling System
Patent # 6,132,320
LEVELAL™

This manual is provided to instruct you during the assembly of your new Fat Cat™ Shot King Pool Table.
Please refer to it as necessary. Be sure to have another person help you assemble the table.
Careful handling of all parts during assembly will ensure many years of enjoyment!
Fat Cat™ Pool Tables use the patented Levelal™ table leveling system to assure your table remains level
and continues to give you the finest playing surface in the industry.
Recommended room size for the Fat Cat™ Shot King Pool Table is 13' 4" x 16' 0" minimum.
Tools
Assembly of the Fat Cat™ Shot King Pool Table requires the following common tools:
• Drill or screw gun with Philips bit • Scissors
• A drill bit for pilot holes • Fine grit sandpaper or emery cloth
• Regular and Philips screwdrivers • Several clean rags
• Socket wrench kit • 2 sheets of folded paper
• Carpenter’s level • Disposable cup
• Tape measure • Putty knife
• Razor knife/Box cutter
Arrange all of your tools before you begin assembly.
Unpacking
Laying out parts in advance allows you to easily follow the assembly instructions.
Carefully remove all components and separate into the following groups:
1. The Pedestal Group: 2 (#21) leg panels, 2 (#22) leg post A, 2 (#23) leg post B, 2 (#25) leg center cross
braces, 4 (#26) support blocks, 4 (#27) leg protectors, 4 (#28) leg levelers, 16 (#2) Philips head screws, and 24
(#1) flat head screws.
2. The Frame Group: 2 (#29) side beams, 2 (#30) center cross beams, 2 (#32) end cross beams, 8 (#4) hex
bolts, 8 (#8) hex bolts, 8 (#5) hex nuts, 8 (#7) spring washers, 24 (#6) black washers, 8 (#10) washers, 8 (#11)
spring washers and 8 (#9) hex bolts.
3. The Slate and Apron Group: 3-piece (#33) slate set, 2 (#35) side aprons, 2 (#36) end aprons, 4 (#37) apron
corner pieces, 24 (#12) screws, 16 (#20) slate screws, 4 (#31) wood plugs and 32 (#13) round head screws.
4. The Cloth Group: 1 piece of (#34) green cloth, 1 (#49) can of spray adhesive, and 1 (#50) bag of joint
compound.
5. The Rail and Pocket Group: 2 (#38) side rail pieces, 2 (#39) end rail pieces, 4 (#40) end rail corner pieces,
6 (#41) drop pockets, 24 (#24) pocket nails, 18 (#18) hex bolts, 18 (#19) washers, 4 (#16) washers and 4
(#15) bolts.
★PRO TIP ★
★PRO TIP ★
★WARNING! Make sure table is assembled on the spot where you plan to keep it. Do not attempt to move
table after it is assembled. Sliding the table may cause it to collapse! ★
2

Step 1: Assembling the Pedestals
For each pedestal, locate the predrilled holes on interior surface of each leg post. Line up predrilled holes
in (#26) support blocks and attach to leg posts with 2 (#2) Philips head screws. Repeat for all.
Next, slide 1 (#21) leg panel into the precut slot into 1 (#22) A and 1 (#23) B leg posts. Make sure bottom
edge of panel is flush with bottom (tapered end) of leg posts. Insert 2 (#2) Philips head screws into
pre-drilled holes on the side of each leg post and secure to panel.
Place 1 (#25) leg center brace on top of (#26) support blocks on each leg assembly. Secure to leg
assembly with 6 (#1) flat head screws. Repeat for other pedestal.
Flip both leg assemblies upside down and attach (#27) black leg protector to each corner with 3 (#1) flat
head screws. Finish by inserting (#28) leg leveler into ferrule on each leg protector. Turn leg assemblies right
side up.
To insure easy alignment of parts, assemble each section loosely before tightening down all
screws/bolts in steps 2&3.
Step 2: Assembling the Base
With the help of another person, set both pedestals upright. (Slotted ends of pedestals face to the outside
of table.) One at a time, place the 2 (#29) side beams in position on top of the pedestals, flat sides facing
out, making sure pre-cut holes in beams are lined up with the 2 holes in the pedestals. Place (#6) black
washer over the end of a (#4) hex bolt and insert through one of the holes in pedestal and side rail, then
add another (#6) black washer and a (#7) spring washer. Finish with a (#5) hex nut and loosely secure.
Repeat for opposite side of pedestal and then other pedestal. Follow the same procedure for the second
hole. Note: It may be necessary to gently apply pressure to pedestals to allow holes to line up. Leave bolts
loose until after step 3.
★PRO TIP ★
28
27
25
21
22
23
1
26
2
2
2
1
1
25
3

Step 3: Attaching the Slate Support Beams
Set (#32) end cross beams on top of side beams, lining up predrilled holes. Attach loosely with 8 (#8) hex
bolts, 8 (#6) black washers, 8 (#10) washers, 8 (#11) spring washers, and 8 (#9) hex nuts. Repeat process for
(#30) center cross beams. Tighten down all bolts to complete base frame.
Place table into position in your room (13' 4" x 17' 0" minimum). Measure ends at base frame to walls, making
sure there is at least 60" between the table and the wall. You do not want to move the table after this step.
Level base frame by placing level on cross beams and level side to side and front to back.
A level base frame gives you the proper foundation for a level playing surface.
8
6
10
11
9
8
6
10
11
9
32
32
30
30
★PRO TIP ★
29
4
6
6
6
7
7
7
4
6
7
529
5
4

Step 4: Securing the Slate
With the help of another person, place the middle section of (#33) slate on the center supports of the base.
Measure from the edge of slate to outer edge of end cross beams. Make sure this piece is centered
perfectly, is square to all sides, and that the overhang is equal on both sides.
Place each end section of slate in position on the base. Check to make sure all sections are flat on the
base. Double-check overhang and if necessary, adjust to make sure it is equal on all sides.
The 3 sections of slate should be set tightly against each other to give the appearance of a
solid table top. Slide a folded piece of paper into the joint between each end section and the
middle section. This prevents the edges of the slate from sticking together and chipping while
slate is being leveled.
Use the (#47) 3/8" Allen wrench to adjust each of the 16 slate levelers (already inserted in the slate by
manufacturer) until all are flush with the base. This is very important.
20
33
20
20
20
20
20
20
20
20
20
20
20
20
31
20
20
20
33
33
31
31
31
★PRO TIP ★
5

Step 5: Leveling the Slate
Using the carpenter’s level determine which of the 3 sections is least level. Begin the leveling process with
this section by adjusting the levelers with the (#47) Allen wrench. When it is level, set the other 2 sections to
match it. Make sure the seams are smooth and all 3 sections are perfectly level. Double check the seams in
several places with your level.
To determine the seams are smooth, slide 2 fingers back and forth across the seams. Do not try
to rush through this leveling process. All sections must be perfectly level if you want the highest
quality playing surface.
With the drill bit, drill a pilot hole through each leveler opening into the base. Be careful to drill straight
down. Insert the (#20) slate screws and fasten the slate to the base. Double check with the level to make
sure all seams are still smooth and all surfaces are level. Any fine tuning can be done by slightly backing off
the screws and readjusting the levelers with the (#47) Allen wrench.
Set a (#31) wood plug into each of the 4 leveling cavities nearest the center of the table (the 12 cavities on
the outside perimeter do not require plugs since they are outside the playing field). Be sure to push
the plug completely into the hole, flush with the table.
Mix a small amount of hardener and (#50) joint compound in a disposable cup.
It is best to mix several small batches of joint compound as it sets quickly and
becomes unworkable.
Using a putty knife apply the compound to the seam area, thinly spreading it toward you. Make sure
the seam is filled completely. Also fill each of the 4 leveler/plug holes and any other imperfections in
the surface.
Allow the compound to dry thoroughly. Lightly hand sand each area until smooth to the touch.
Do not over-sand or use an electric sander. This can cause a “dip” in the slate and ruin the
playing surface.
Step 6: Applying the Cloth
Before applying the cloth make sure that slate has been wiped down and is free of any dirt or
particles. Be sure your hands are clean before handling the cloth. Any adhesive residue may
be removed from the cloth with duct tape.
Locate sticker on one side of (#34) cloth. This is the top side or playing surface. Unfold and center cloth,
playing surface up, on top of the clean slate. Make sure the overhang is equal on all four sides.
Starting at one end of the table, fold the cloth over and expose about 3 inches of slate. Carefully spray a
1-1/2" wide strip of (#49) adhesive along the top edge of the slate. Also spray the outer edge, avoiding the
pocket cut outs. Repeat this procedure at the opposite end. Allow the adhesive to set until tacky to the
touch (usually several minutes).
After the adhesive has set, secure the cloth at one end of the table by starting in the middle and smoothly
stretching the cloth out to each of the corner pockets.
★PRO TIP ★
★PRO TIP ★
★PRO TIP ★
★PRO TIP ★
6

Move to the center of the opposite end of the table. With one hand, pull the cloth tightly toward you until
you have a 1-1/2" fold in the center of the cloth and with the other hand press it firmly into place. Pull the
sides of the cloth tightly toward their respective corners. Smooth and press firmly, always working from
center to corner.
Repeat this process on the sides of the table. Start from the center pocket on one side of the table and pull
toward you, taking up half of the fold from the center of the cloth. Smooth into place working from the
center out to the corner pockets. On the opposite side start from the center pocket and pull toward you,
taking up the remaining fold from the center of the cloth. Smooth into place working from the center out to
the corner pockets. The cloth should be smooth and tight. Using your scissors or box cutter, trim the cloth
until even with the bottom edge of the slate.
Carefully spray adhesive on the edge and underside of the pocket area. Also spray the underside of the
cloth with adhesive.
Cut 3 pie shaped wedges in the cloth at the corner pocket cut outs. Fold cloth down and under to wrap
cut out edges. Cut 5 pie shaped wedges in the cloth at the side pocket cut outs. Fold cloth down and
under to wrap cut out edges.
Be very careful to not cut past the table’s top edge and into the playing surface when cutting
the wedges.
★PRO TIP ★

7

Press the cloth firmly against the slate along the curve of all pockets. Trim off excess cloth with scissors or
box cutter.
Locate the 18 holes for the rail bolts along the perimeter of the tabletop. Carefully punch holes in the cloth.
Using a Philips screwdriver, run the shaft of the screwdriver around the sharp edge of the holes
in the slate. This gives the perfect hole. Be careful not to punch through slate screw holes.
Step 7: Attaching the Apron
With the help of another person, place (#35) apron section on side of table, making sure the apron is
centered to slate. Fix to base with 4 (#12) flat head screws. Repeat process for other apron sections.
Slide the (#37) apron corner onto each side of the (#36) end apron and fasten with 8 (#13) screws. Place
the end apron onto the table and secure the apron corner to the (#35) side apron with 4 (#13) screws.
Fasten the end aprons and side aprons to the table with 4 (#12) flat head screws. Repeat for other half.
13
37
37
12
12
36
36
37
13
12
12
12
12
12
12
35
37
★PRO TIP ★
8

9
Step 8: Assembling Rails and Pockets
Set all rail pieces into position on table top. Loosely attach (#38) side rail section to base on the underside
of table with (#18) hex bolts and (#19) washers. Loosely attach (#39) end rails in same manner. Slide (#40)
corner pieces on loosely. Adjust rail fit as needed. Secure corners on underside of table with (#15) bolts and
(#16) washers. Tighten all rail bolts securely. Snap drop pockets together, cut as indicated, insert into pocket
cutouts in the table and secure with (#24) pocket nails. Make sure rails are square and straight w/respect to
the pockets and slate.
YOU ARE NOW READY TO PLAY!
18
19
16
15
16
15
16
15
18
19
Cut here
for corner
pockets.
Cut here
for side
pockets.
24
24
39
39
38
38
40
40
40

#27.
Leg Protector
4 Pieces
10
#24.
Pocket Nails
24 Pieces
#25.
Leg Center Brace
2 Pieces
#26.
Support Block
4 Pieces
#22.
Leg Post A
2 Pieces
#23.
Leg Post B
2 Pieces
#15.
1/4" x 1/2"
Allen Bolt
4 Pieces
#16.
1/4" x 32mm
Washer
4 Pieces
#18.
5/16" x 1-3/4"
Hex Bolt
18 Pieces
#19.
5/16" x 35mm
Washer
18 Pieces
#5.
3/8" Hex Nut
8 Pieces
#6.
3/8" x 1"
Black Washer
24 Pieces
#7.
3/8" x 14mm"
Spring Washer
8 Pieces
#8.
5/16" x 2-1/2"
Hex Bolt
8 Pieces
#9.
5/16" Hex Nut
8 Pieces
#10.
5/16" x 23mm
Washer
8 Pieces
#12.
#8 x 1-1/2"
Flat Head Screw
24 Pieces
#11.
5/16" x 14mm
Spring Washer
8 Pieces
#13.
T4 x 1/2"
Round Head Screw
52 Pieces
#2.
#8 x 1-1/2"
Philips Head Screw
16 Pieces
#4.
3/8" x 2-1/2"
Hex Bolt
8 Pieces
#20.
#12 x 2"
Slate Screw
16 Pieces
#21.
Leg Panel
2 Pieces
#1.
#8 x 1-1/4"
Flat Head Screw
24 Pieces
Fat Cat™Shot King Pool Table Parts List

#47.
Allen Wrench
1 Large, 3 Small
#39.
End Rail
2 Pieces
#40.
End Rail Corner
4 Pieces
#41.
Drop Pocket
12 Pieces
#42.
Felt Brush
1 Piece
#43.
Chalk
2 Pieces
#44.
Billiard Balls
1 Set
#45.
Triangle
1 Piece
#46.
2 Cue Sticks
4 Pieces
#37.
Apron Corner
4 Pieces
#38.
Side Rail
2 Pieces
#50.
Joint Compound
1 Bag
#31.
Wood Plug
4 Pieces
#32.
End Cross Beam
2 Pieces
#33.
Slate Set
3 Pieces
#34.
Cloth
1 Piece
#28.
Leg Leveler
4 Pieces
#29.
Side Beam
2 Pieces
#30.
Center Cross Beam
2 Pieces
#35.
Side Apron
2 Pieces
#36.
End Apron
2 Pieces
11
Fat Cat™Shot King Pool Table Parts List (continued)
#48.
Wrench
1 Piece
#49.
Spray Adhesive
1 Can

GLD Products
S84 W19093 Enterprise Drive
Muskego, WI 53150 USA
800 225 7593 • FAX [phone]
Email: [email protected]
DO NOT RETURN TO STORE
For all returns and warranty coverage, please call:
GLD Products
1-800-225-7593
Please provide model number, serial number and/or part
number when you call. Numbers can be found on outside
of packaging.
WARRANTY INFORMATION
1 Year Warranty on Shot King™ Pool Table
Manufacturer warrants to the original retail purchaser, this product
to be free from defects in material and workmanship for a period
of one (1) year from the date of purchase.
For ten (10) years from the date of purchase for slate, we will repair
the playing surface of this table, free of charge, if it fails to remain
flat, within a tolerance of ±30/1000 of an inch, measuring from any
flat plane within the playing surface. Note: Cloth not included in
warranty. Should this product become defective due to material
or workmanship within the warranty period, contact our Customer
Service Department. This warranty is not transferable and does not
cover normal wear and tear, or damage caused by improper
handling, installation or use of this product. This warranty is also void
if product is in any way abused, damaged or modified from its
original state, or if used for other than indoor residential use. This
warranty gives you specific legal rights and you may have other
rights which vary from state to state.