feather&black Ottoman User manual

1
Assembly tool and instructions
Step By Step Assembly Instructions
Pre-assembly Preparation
PLEASE READ these instructions fully prior to assembly to familiarise yourself with the various stages of construction.
Carefully open all packs supplied and check the contents against the parts and fittings check list.
Do not destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
This product is HEAVY, it should be assembled as near as possible to the point of use.
Take care when lifting to avoid personal injury and (or) damage to the product.
This product takes approximately 60 minutes to assemble by a minimum of two people.
Please ensure that the packaging is disposed of in a safe environmentally friendly way.
There are small components used in the construction of this bed as well as plastic foil packaging,
these should be kept away from young children whilst assembling your bed.
This product is not a toy, it contains moving parts and as such children should be supervised at all times when using the
mechanism.
Do not climb or stand inside the storage compartment and ensure that the area is clear before operating the mechanism.
(Do not operate the mechanism with anybody on the bed)
The locking strap must always be attached before moving or turning your mattress (see separate instructions).
Do not attempt to operate/close the mechanism without a mattress in place.

2
Z
X
X
Y
V
V
V
V
W
U
U
T
T
T
T
S
S
R
R
Q
Q
P
P
O
O
N
N
M

3
Part identification
Qty
Z
Headboard
1
Y
Footboard
1
X
Side panel
Left
Right
1
1
W
Centre rail
1
V
Legs
4
U
Landing brackets
2
T
Corner brackets
4
S
Centre rail brackets
2
R
Lift-up mechanism
Left
Right
1
1
Q
Metal frame with slats
Left
Right
1
1
P
Frame linking brackets
2
O
Bottom panel
2
N
Support block
2
M
Plastic glider
1
Fittings list
Qty
K
4x50 mm Screw
2
J
M6x35 mm Countersunk bolt
4
I
Nut
Small M6
Large M8
4
3
H
Washer
Small M6
Large M8
4
3
G
M6x40 mm Machine screw
18
F
M8x35 mm Hex bolt
4
E
M8x60 mm Hex bolt
3
D
M8x60 mm Hex key bolt
2
C
M8x80 mm Hex key bolt
2
B
5 mm Hexagon key
1
A
13 mm ring spanner
1
A
B
TOOLS REQUIRED
10 mm ring spanner Screwdriver
D
E
F
G
H
I
J
K

4
step1
Attach the legs and landing brackets to the headboard and footboard.
step2
Unscrew the bolts on the headboard and footboard by approximately 10mm (3/8”).
While holding the headboard upright, hook the side panels onto the bolts.
Hook the side panels onto footboard, hand tighten all the bolts. Ensure that the bed is square (90° at all
corners) then tighten all of the bolts fully on the headboard and footboard, using the ring spanner supplied.
Z
G
Y
D
U
V
C
G
Note: Begin with the headboard.
Note: Ensure that the side panels are
pushed fully down with the bolt heads
located to the top of the slots.
10mm
(3/8”)
X
X
Note: Before securing the landing bracket (U)
to the footboard (Y) attach strap ‘1’ from the
Locking Strap Kit as shown on the separate
instruction sheet.
T

5
step3
Fit the centre rail hook into position on the headboard, then footboard and then push down to secure.
step4
Screw the lift-up mechanisms to the side panels.
W
R
G
G
G
G
G
S