Federal Signal Corporation MPSM6-LPV2 User manual

25500591
Rev. A0 0719
Printed in U.S.A.
Model MPSM6-LPV2
Adjustable Mounting Kit
for MicroPulse®
Installation Instructions

Limited Warranty
This product is subject to and covered by a limited warranty,
a copy of which can be found at www.fedsig.com/SSG-Warranty.
A copy of this limited warranty can also be obtained by written
request to Federal Signal Corporation, 2645 Federal Signal Drive,
University Park, IL 60484, email to [email protected] or call
[phone].
This limited warranty is in lieu of all other warranties, express or
implied, contractual or statutory, including, but not limited to the
warranty of merchantability, warranty of tness for a particular
purpose and any warranty against failure of its essential purpose.
2645 Federal Signal Drive
University Park, Illinois 60484
www.fedsig.com
Customer Support
Police/Fire-EMS: 800-264-3578 • [phone]
Work Truck: 800-824-0254 • [phone]
Technical Support 800-433-9132 • [phone]
© 2019 Federal Signal Corporation
TAPTITE is a trademark of RESEARCH ENGINEERING &
MANUFACTURING, INC.

3
Installation Instructions for MicroPulse Mounting Kit
MPSM6-LPV2 Adjustable Mounting Kit
Federal Signal www.fedsig.com
Safety Message to Installers of Warning Light Equipment
People’s lives depend on your proper installation and servicing of
Federal Signal products. It is important to read and follow all instructions
shipped with this product and the original product. In addition, listed
below are some other important safety instructions and precautions you
should follow:
• To properly install the lighting system, you must have a good
understanding of automotive systems, along with prociency in the
installation and use of safety warning equipment.
• Do not install equipment or route wiring in the deployment path of an
airbag.
• If a vehicle seat is temporarily removed, verify with the vehicle
manufacturer if the seat needs to be recalibrated for proper airbag
deployment.
• You should frequently inspect the light system to ensure that it is
operating properly and that it is securely attached to the vehicle.
• When drilling into a vehicle structure, be sure that both sides of the
surface are clear of anything that could be damaged.
• Refer to the instructions packed with related products for additional
precautions and information.
• File these instructions in a safe place and refer to them when
maintaining and/or reinstalling the product.
• Do not stare directly into the lights at a close range, or permanent
damage to your eyesight may occur.
Failure to follow all safety precautions and instructions may result in
property damage, serious injury, or death.

4
Installation Instructions for MicroPulse Mounting Kit
MPSM6-LPV2 Adjustable Mounting Kit
Federal Signal www.fedsig.com
Unpacking the Kit
After unpacking the product, inspect it for damage that may have
occurred in transit. If it has been damaged or is missing a part, do not
attempt to install or operate it. File a claim immediately with the carrier,
stating the extent of the damage. Carefully check all envelopes, shipping
labels and tags before removing or destroying them. Ensure that all parts
in Table 1 have been included. If you are missing any parts, contact
Customer Support at 1-800-264-3578, 7 a.m. to 5 p.m., Monday through
Friday (CT).
Introduction
This publication has instructions for using the Adjustable License Plate
Mounting Kit to mount the MPS600U lighthead to the license plate area
of many vehicles. The assembled unit is 6-3/4 inches high by 18-3/4
inches wide.
NOTE: For electrical installation instructions, refer to the Installation
and Maintenance Instructions packed with the lighthead.
Table 1 Kit Contents
Qty. Description Part Number
4 1/4"-20 Hex Head Stainless Steel Machine Screw 7000A311-08
8 6-32, Pan Head Phillips Stainless Steel Machine Screw 7000491-08
6 8-32 6-Lobe Pan Head TAPTITE Screw 7011163-04
4 #10 Type B Black Stainless Steel Flat Head, 6-Lobe Screw 7011248-08
8 6-32 Stainless Steel Keps Nut 7058A046
4 1/4-inch Flat Stainless Steel Washer 7072A024
4 1/4-inch Stailess Steel Split Lock Washer 7074A016
1 Low License Plate Bracket Assembly MPSM6-LPV2 861303105
2 MPS MNT Dual Licence Plate Bracket MPSM6-LPV1 861302682
1 Hat License Plate Bracket Plate MPSM6-LPV2 861303106

5
Installation Instructions for MicroPulse Mounting Kit
MPSM6-LPV2 Adjustable Mounting Kit
Federal Signal www.fedsig.com
Figure 1 Exploded view of the MPSM6-LPV2 kit installation
Installing the Kit
AIRBAG DEPLOYMENT: Do not install or route wiring in the
deployment path of an airbag. Failure to observe this warning will
reduce the effectiveness of the airbag or potentially dislodge the
equipment, causing serious injury or death.
DRILLING PRECAUTIONS: Before drilling holes, check the area
you are drilling into to be sure that you do not damage vehicle
components. All drilled holes should be de-burred, and all sharp
edges should be smoothed. All wire routings going through drilled
holes should be protected by a grommet or convolute/split loom
tubing.
THREAD DAMAGE AND GALLING: To prevent thread damage and
galling, anti-seize must be used on all stainless steel fasteners.
IMPORTANT: Plan all cable routing before the installation.

6
Installation Instructions for MicroPulse Mounting Kit
MPSM6-LPV2 Adjustable Mounting Kit
Federal Signal www.fedsig.com
To mount the bracket:
1. Remove the license plate mounting hardware, license plate, and
bracket from the front of the vehicle.
2. Mount the hat bracket to the vehicle with the factory license
plate hardware removed in Step 1. For the most secure mounting,
install hardware at all four positions.
3. Loosely assemble the MPS mounting brackets to the license plate
bracket with the six 8-32 pan head screws.
4. Hold the assembly to the hat bracket and adjust the MPS brackets
to the desired angle, and then tighten the screws. Do not over-
tighten.
5. Use the 6-32 screws and Keps nuts included with the kit to attach
the light heads to the brackets.
6. Secure the assembly to the hat bracket with the four #10 at head
screws.
7. Mount the license plate with the supplied 1/4-inch screws,
washers, and lockwashers.
LIGHT HAZARD: To be an effective warning device, an emergency
warning system produces bright light that can be hazardous to you
eyesight when viewed at close range. Do not stare directly into the
lights at a close range or permanent damage to your eyesight may
occur.
8. Test the lights for proper operation.

7
Installation Instructions for MicroPulse Mounting Kit
MPSM6-LPV2 Adjustable Mounting Kit
Federal Signal www.fedsig.com
Getting Technical Support and Service
For technical support and service, please contact:
Service Department
Federal Signal Corporation
Phone: [phone]
Email: [email protected]
Getting Repair Service
The Federal Signal factory provides technical assistance with any
problems that cannot be handled locally.
Any units returned to Federal Signal for service, inspection, or repair
must be accompanied by a Return Material Authorization (RMA). Obtain
a RMA from a local Distributor or Manufacturer’s Representative.
Provide a brief explanation of the service requested, or the nature of the
malfunction.
Address all communications and shipments to the following:
Federal Signal Corporation
Service Department
2645 Federal Signal Drive
University Park, IL 60484-3167
Ordering Replacement Parts
To order replacement parts, call Customer Support at 1-800-264-3578,
7 a.m. to 5 p.m., Monday through Friday (CT) or contact your nearest
distributor.

2645 Federal Signal Drive
University Park, Illinois 60484
www.fedsig.com
Customer Support
Police/Fire-EMS: 800-264-3578 • [phone]
Work Truck: 800-824-0254 • [phone]
Technical Support 800-433-9132 • [phone]