Fellowes Kataex1-dc-fm series User manual

installation instructions

Kata™EX-FM

Model# KATAEX1-DC-FM-___

Model# KATAEX1-GM-FM-___

___ = SLV, BLK or WHT

single xed+motion monitor arm

Page 2

KataEX-FM Components and tools

Please review these instructions before beginning the installation. Use the illustrations below to check that all the components needed for your

installation were provided with your order. Do not discard the packaging until the product works to your satisfaction.

Components and tools

Additional tools required

• Phillips screwdriver

Caution

• Hand tighten screws only. Do not use power tools.

clamp or grommet mounting:

VESA plate screws (4) set screws (3)

decorative covers (set of 4)cable clip (1) cable clip (1)

dual Allen key (1)

2mm and 4mm

monitor arm assembly (1) connection

sleeve (1)

M4x10 M4x15

clamp mounting only: grommet mounting only:

grommet base

assembly (1)

clamp base

assembly (1)

base

cover (1)

grommet bar (1)

grommet knob (1)

base

cover (1)

Page 3

KataEX-FM Assembly

0.5" – 2.1" 0.5" – 1.5"

clamp to

worksurface

ﬁt base cover

over base

ﬂush

against

clamp

gap

Follow either step #1a for clamp mounting or step #1b for grommet mounting. All other steps apply to both mounting methods.

Step #1a: attach base assembly to worksurface — clamp mounting

The thickness of the worksurface must be between 0.5" and 2.1". To mount the clamp ﬂush against

the worksurface, the thickness must be no more than 1.5".

• Loosen the clamp suciently to be able to slide it easily onto the worksurface.

• Clamp the assembly to the worksurface in the desired position. Be sure to tighten the clamp securely.

• Place the base cover onto the mounting post and ﬁt the cover over the base.

Step #1b: attach base assembly to worksurface — grommet mounting

Maximum thickness of the worksurface for grommet mounting is 1.7".

• Place the base assembly over the grommet hole with the bolt centered.

• Insert the grommet bar onto the grommet bolt and then screw on the grommet knob. Tighten the grommet knob securely to hold the base assembly in position.

• Place the base cover onto the mounting post and ﬁt the cover over the base.

maximum thickness = 1.7"

center bolt in grommet hole

grommet base assembly

tighten grommet knob to secure

grommet bar

ﬁt base cover

over base

Page 4

KataEX-FM Assembly

Step #2: install monitor arm

1. Rotate the locking ring counterclockwise to unlock it. Remove the locking ring from the connection sleeve.

2. Slide the connection sleeve onto the post with the screw toward the rear. With the sleeve at the desired height, tighten the screw using the 4mm Allen key.

3. Install the monitor arm onto the connection sleeve by sliding its tabs into two slots on the sleeve.

— The tabs can ﬁt into any two slots on the sleeve. In the example below, the arm stem points forward, toward the user.

4. Carefully cut the decorative covers to remove them from the set. Slide the covers into the unused slots on the connection sleeve.

5. Lock the monitor arm to the connection sleeve with the locking ring. Rotate the locking ring clockwise to secure it.

Step #3: attach VESA plate to monitor

• Remove the VESA plate from its VESA mount by (1) pushing forward the tab at the top and (2) lifting upward.

—TIP: Practice re-installing the VESA plate before attaching it to the monitor. This will make step 4 easier.

• Place the monitor face down on a ﬂat surface. Align the VESA plate holes with the holes on the back of the monitor. Attach the VESA plate using the four VESA plate

screws provided.

— There are two sets of four holes on the VESA plates. One set has holes 3.9" (100mm) apart, the other set has holes 3" (75mm) apart. Use the set that matches the

holes on the rear of the monitor.

4mm

Allen key

tabs

connection

sleeve

to unlock

turn locking ring

counterclockwise

lift o

decorative

covers

5turn locking ring

clockwise to lock

lift o VESA plate

VESA plate screw

VESA

plate monitor

(face down)

top

3.9"

(100mm)

(75mm)

push tab forward

Page 5

KataEX-FM Assembly

Step #4: attach monitor to VESA mount

• Slide the VESA plate (with monitor attached) back onto the VESA mount.

— Make sure the VESA plate clicks securely in place.

• OPTIONAL: Secure the VESA plate to the VESA mount using one of the M4x15 set screws, as shown below.

Step #5: remove cable management covers

• To remove the cable covers from the arm stem and ﬁxed arm, slide

the covers outward.

• To remove the cable cover from the motion arm, slide the cover upward.

attach

monitor

VESA

mount

VESA

plate

set screw

M4x15

2mm Allen key

slide out

ﬁxed arm

arm stem

slide up

motion arm

Page 6

KataEX-FM Assembly

Step #6: install lockout set screw(s), if desired

Default rotation of the ﬁxed arm and motion arm is 360°. Installation of a lockout set screw limits rotation to 180°.

• To lockout rotation of the ﬁxed arm, install one of the M4x15 set screws in the underside of the arm stem. Tighten the screw, then back it o one turn.

— Installing a set screw in the front hole allows 180° rotation to the right only. A set screw in the rear hole allows 180° rotation to the left only.

• The ﬁxed arm or motion arm must be in its allowed range of rotation when installing the lockout set screw.

Step #7: organize cables and cords

• Capture the cables and cords with the cable covers. Slide the cable covers as shown to attach them to the monitor arms.

• Snap the cable clips onto the post and into the recessed groove above the base.

• Route the monitor cables and power cords toward the rear by slipping the cords into the opening on the cable clips.

180°

front screw

rear screw

180°

front screw

rear screw

set screw

M4x15

2mm

Allen key

front

rear

capture

cables

with clips

snap on

cable clips

install covers over cables

slide in

slide

down

Page 7

KataEX-FM Assembly

Step #8: make any necessary adjustments

There are ﬁve possible swivel and tilt tension adjustments:

1. Monitor tilt adjustment

— Use the 4mm end of the dual Allen key to loosen the screw on the side of the VESA mount to change monitor tilt angle. Tighten the screw to hold the angle.

2. Monitor swivel adjustment

— Use the 4mm end of the dual Allen key to adjust the underside screw behind the VESA mount for the desired ease of monitor rotation.

3. Motion arm swivel adjustment

— Use the 4mm end of the dual Allen key to adjust the underside screw at the end of the ﬁxed arm for the desired ease of monitor arm rotation.

4. Fixed arm swivel adjustment

— Use the 4mm end of the dual Allen key to adjust the underside screw at the end of the arm stem for the desired ease of ﬁxed arm rotation.

5. Motion arm weight adjustment

— Use the 4mm end of the dual Allen key to adjust the screw at the end of the motion arm for the appropriate monitor weight. When adjusted properly, the monitor

weight is balanced, making it easy to raise or lower the monitor.

monitor

not shown

behind

VESA

plate

LIMITED WARRANTY

ESI warrants this product to be free from defects in manufacturing for a period of 15 years from the date of original purchase. This warranty extends only to the original purchaser, and does not apply

if the product has been damaged or fails to function properly as a result of misuse, abuse, modiﬁcation, alteration, or improper cleaning or maintenance. This warranty does not apply to damage

in shipment caused by carriers, damage caused during installation, normal wear and tear, or excessive use (meaning consistent use in excess of an eight hour shift). ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL RETAIL PURCHASE. ESI’s sole obligation under this warranty

or any implied warranty, and the purchaser’s sole remedy, is limited to the repair or replacement, at ESI’s option, of the product or any defective part. Costs (such as installation, labor fees or express

shipping) incurred due to replacement of products are not covered under warranty. IN NO EVENT SHALL FELLOWES, ITS AFFILIATES, SUBSIDIARIES, RELATED ENTITIES OR THEIR RESPECTIVE OFFICERS,

DIRECTORS, OR EMPLOYEES, BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY, OR SPECIAL DAMAGES.

To make a warranty claim, contact ESI at 800-833-3746 or [email protected]. You must provide proof of purchase, such as the original purchase order number.

The duration, terms and conditions of this warranty are valid worldwide, except where dierent limitations, restrictions or conditions may be required by local law.

Kata™EX-FM

single xed+motion monitor arm

Please contact Customer Service with any questions or

comments at 800.833.3746 or visit our website at esiergo.com

This manual suits for next models

Table of contents

Other Fellowes Rack & Stand manuals