Fencee MX10 User manual

1
EN
User
manual
REMOTE MONITORING
OF FENCE PARAMETERS
Wireless RF connection with the Gateway.
IT DOES NOT NEED A SIM CARD
No additional operating costs.
Electric fencing
WORKS ONLY WITH:
To download
fencee Cloud
[phone]
www.fencee.eu
www.fenceefarm.com

2
Thank you for purchasing the MX10 Monitor from VNT electronics s.r.o.
The device complies with the safety regulations according to the valid
law as well as the relevant EU regulation (CE).
The device complies with the Council of Europe Directive 2014/53/EC, meets the requirements
of the General License of the Czech Telecommunication Oce according to the general authorization
No. VO-R/10/05.2014-3, and it also complies with the below requirements of the standards and regulations
applicable to this type of equipment:
2014/35/EU I2014/30/EU IR&TTE EN300-220 a EN 61000-6-3:2007 + A1:2011
ETSI EN 301 489-1 V1.9.2 I ETSI EN 301 489-3 V1.6.1 I ETSI EN 300 220-2 V.2.4.1
ETSI EN 60950-1 ed.2:2006 /A1:2010 /A11:2009 /A12:2011 /A2:2014/Opr.1:2012 EN 62479:2010
We recommend that you read this manual carefully
before using the device and keep it for future reference!
CONTENT
1introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2Overview of the main benets of the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3Technical parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
5Description of the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6Description of controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
7Pairing the Monitor with the Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
8Connection with Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
9Installing the Monitor on a fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
10 Troubleshooting - possible fault sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
11 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Find out all the information
about the Monitor in our video.

3
1. INTRODUCTION
Use this device to ensure better protection of your animals and land.
Local conditions and circumstances always aect the function of the device and therefore
we cannot guarantee complete protection against breach of the fence. The energizer
manufacturer does not warrant that there will be no breakdown of the fence installation and
does not guarantee that animals cannot run away. The installation of a fence should increase
the safety of the animals in the fence system or protect the land.
Please follow the instructions for use of this device.
Important Notice
•Switch off the electric fence before carrying out any work on the energizer or fence.
•Read the Safety Instructions carefully.
•When installing, make sure that you observe all safety regulations.
•Use only original spare parts.
2. OVERVIEW OF THE MAIN BENEFITS OF THE MONITOR
•LED indication
•Audible indication
•No SIM Card required
•Magnet controlled
•Possibility of connecting an external antenna
4. PACKAGE CONTENTS
•MX10 Monitor
•Two C-LR14 batteries
•Magnet with a string
•Earthing pin
•Earthing cable for grounding
•Connecting cable to the fence system
•RF Antenna
•2 pcs plastic cable tie for mounting on a post
3. TECHNICAL PARAMETERS
•Range with basic antenna up to 10 km (included)
•Possibility of connecting an external antenna
(extension cable 2 m or 10 m - range increase up to 30 km)
•RF transmission frequency - 869.525 MHz /22 dBm
•Power battery: 2 × C-LR14
•Dimensions: 78 × 144 × 42 mm
•Weight: 370 g

4
Connector for
connection to the fence
LED diode
5. DESCRIPTION OF THE DEVICE
•The Monitor MX10 is used to measure voltage anywhere in your fence system.
•Up to 12 MX Control Monitors can be pair to a Gateway and divided the enclosure into
multiple zones. Everything then communicates with the central Gateway and the
RF energizers fencee power DUO RF PDX or fencee energy DUO RF EDX
(energizer not included Monitor package)
•Using radio frequency technology, it transmits the measured data wirelessly to the central
Gateway, where the values are shown on the display.
•In the event of a voltage drop at the measured point below the set limit, an alarm is sent
and signalling to the Gateway immediately notifies the user of the fault.
RF antenna
SMA connector for
antenna connection
Magnetic target
Earthing connector

5
Inserting the batteries
•Unscrew the screws and open the cover on the back of the Monitor.
•Insert two C-LR14 batteries according to the instructions in the plastic cover.
•Return the cover to its original position and tighten the screws firmly.
2 × C-LR14
An opening
for the cable tie
An opening
for the cable tie

6
6. DESCRIPTION OF CONTROLS
Power supply
The Monitor is powered by two C-LR14 batteries, which must be inserted through the back
cover and the correct polarity must be observed. It is recommended to install alkaline
batteries for longer life. The battery status is indicated in the Gateway as a percentage.
Battery life is about 1 year.
Control
The device is controlled by the included magnet, which must be attached to the target on
the side of the MX10 Monitor. When the magnet approaches, the status of the Monitor is
indicated by an LED diode:
Red = o
Green = on
If no LEDs light up, the batteries need to be checked and replaced.
Switching on
Place the magnet on the target for about two seconds.
The Monitor rst beeps and lights up the red indicator LED. Subsequently, the Monitor will
ash green and beep 3 times. The Monitor is now on and indicates its ON status by regular
ashing green LED. When the Monitor is ON, it indicates its activity for a limited time of
2 minutes to save battery power.
Shutdown
By bringing the magnet closer to the target for about two seconds.
The Monitor rst beeps and lights up the green indicator LED.
Then the Monitor will ash red and beep twice.
The Monitor is now turned o.
You can check the status at any time - by bringing the magnet
closer to the target for <1s. The colour of the LED indicates the
status: red = off, green = on.
TIP:

7
The Monitor can only be paired to one Gateway - after pairing with
another Gateway , the previous device will be deleted. The pairing
mode ends automatically after 1 minute or it can be interrupted by
applying a magnet to the target.
7. PAIRING THE MONITOR WITH THE GATEWAY
First, the MX10 Monitor must be paired with the Gateway in order to display the measured
data. Pairing is performed by the following steps:
1The Monitor must be turned o. The LED ashes red.
2Then hold the magnet to the Monitor target for >3 s. The Monitor will ash green
and red LED simultaneously. The Monitor is now in pairing mode.
3Place the Monitor and Gateway next to each other, up to a maximum distance
of approx. 30 cm.
4Now activate the pairing mode also on the Gateway - the exact description is given
in the user manual for the Gateway.
- To select pairing, hold down the MENU button.
- Use the arrow keys to navigate to Pairing and press the ENTER button to access
the Device Manager
- Use the arrow keys to navigate to an empty position
- Press the ENTER button shortly to conrm the item selection
- The correct action is conrmed by the Pairing new device information screen
5Upon successful pairing, the Monitor beeps and ashes green. At the same time it also
automatically shuts o so as not to trigger the alarm immediately, because it is not
connected to the fence yet and has no voltage. It is displayed on the Gateway with
a value of 0 kV.
6The Monitor is now paired and can be installed on the fence system in the required
measuring point.

8
8. CONNECTION WITH GATEWAY
Monitor measures each pulse in the fence system and sends the values to the Gateway every
15 minutes. If a voltage lower than the set limit is measured , data is sent to the Gateway
immediately and an alarm is triggered.
Setting the low voltage alarm level on the fence system
The 3 kV limit is set at the factory. The user can freely adjust this value in the Gateway (see
instructions for the Gateway). If the alarm limit on the Gateway is changed, it will not take
eect in the Monitor until the next time new data is received, i.e. in a 15 min cycle.
Low battery alarm
The Monitor‘s low battery is indicated on the Gateway when it drops below 10%.
We recommend replacing it within 2 weeks at the latest.
Display of the paired Monitor on the Gateway and all available information about
a specific device.
DETAILED SCREEN
1Type of device
2Time since last data transfer
3Monitor battery voltage status [%]
4Current set value for triggering an alarm [kV]
5Fence voltage value [kV]
6Signal level between Monitor and Gateway

9
9. INSTALLING THE MONITOR ON A FENCE
After pairing the Monitor with the Gateway, it is possible to place the Monitor in the desired
location of measurement on the fence system.
Before installation, it is necessary to turn o the energizer, in order to ensure safe handling.
We install the Monitor as shown in gure.
After installation, it is possible to turn on the energizer and turn on the Monitor.
Placement rules:
The Monitor can be installed outdoors in an fence system, it is resistant to normal weather
conditions.
The Monitor can be easily installed with cable ties.
Never place the Monitor on the ground - in a humid or wet environment.
Never expose the Monitor to a continuous stream of water.
For a better signal and connection within 30 km
it is possible to use an external antenna.
TIP:

10
Installation examples
TIP:
Put the monitor in the key sections where voltage needs to be
checked (fence entrance) or where frequent problems,
for example, with vegetation, by the forest, by the water,
or when disconnected fence gate, can be expected.
Standard installation
Fence divided into sections.
If the voltage of a monitor drops,
the section and location of the
problem can be easily identied.
For fence entrances and in problematic
locations - sections
Installation for an easy identication
of the fence with a non-functional energizer
or the location where problems may occur
frequently, e.g. by the forest, by the water,
in locations with dense vegetation.