FERREX FBGS240E1 User manual

User Manual
BENCH GRINDER
Contents
3
Dok./Rev.-Nr. 705990_20220210
AFTER SALES SUPPORT 705990
1300 855 831
[email protected]
MODEL:
FBGS240E1
3
YEAR
WARRANTY
AU
Made in China
FERREX®is a registered trademark of ALDI Stores
DISTRIBUTED BY:
ALDI STORES
1 SARGENTS ROAD
MINCHINBURY NSW 2770
www.aldi.com.au
AU
ALDI guarantees that our exclusive brand products are developed to our
stringent quality specifications. If you are not entirely satisfied with this
product, please return it to the nearest ALDI store within 60 days from the
date of purchase, for a full refund or replacement, or take advantage of our
after sales support by calling the supplier’s Customer Service Hotline.
08/2022
2 3
2
1
7
13
A
B
14
1
1
2
6
9
5
4
18
17
12
19
11
15
8
21
13
14
3
10
10
7
16
20
Overview ..................................................................................... 3
Package contents/part list .........................................................6
Explanation of Symbols .............................................................. 7
Introduction ................................................................................8
Layout ..........................................................................................9
Scope of delivery.........................................................................9
Intended use ..............................................................................10
Safety regulations...................................................................... 11
Assembly ....................................................................................15
Operation....................................................................................16
Working instructions..................................................................17
Cleaning and maintenance........................................................19
Technical data ........................................................................... 20
Storage and transport ...............................................................21
Disposal and recycling ...............................................................21
Troubleshooting........................................................................ 22
Warranty Details........................................................................ 24
Repair and Refurbished Goods or Parts Notice ....................... 26

56 4
45
6 7
4
5
3
15
111217 19
10a
10b
18
21
63a 3b 3
Package contents/part list
1Bench Grinder, 1x
2Spark protection, 1x
3Adjusting screw for spark protection, 1x
4Workpiece support, 2x
5Sanding belt, 3x
6Warranty card
7Instruction manual

Kapitelüberschrift
7
Explanation of Symbols
The use of symbols in this manual is intended to draw your attention to possible risks.
The safety symbols and the explanations that accompany them must be perfectly un-
derstood. The warnings in themselves do not remove the risks and cannot replace
correct actions for preventing accidents.
Warning: Read the operating instructions to reduce the risk of
injury
Wear ear-muffs. The impact of noise can cause damage to
hearing.
Wear a breathing mask. Dust which is injurious to health can be
generated when working on wood and other materials. Never
use the device to work on any materials containing asbestos!
Wear safety goggles. Sparks generated during working or splin-
ters, chipsand dust emittedbythe device cancause loss of sight.
Wear protective gloves.
Never use faulty grinding disks.
Caution! Risk of electric shock!
Made in China
Complies with the Australian norms and standards.
3
36
Warranty period.
Warranty class.
Explanation of symbols

Kapitelüberschrift
8
Introduction
Congratulations on choosing to buy a FERREX®product.
All products brought to you by FERREX®are manufactured to the highest standards
of performance and safety, and as part of our philosophy of customer service and
satisfaction, are backed by our comprehensive 3 Years Warranty.
We hope you will enjoy using your purchase for many years to come.
Note:
According to the applicable product liability law the manufacturer of this device is
not liable for damages which arise on or in connection with this device in case of:
• improper handling,
• non-compliance with the instructions for use,
• repairs by third party, non-authorised skilled workers,
• installation and replacement of non-original spare parts,
• improper use.
Recommendations:
Read the entire text of the operating instructions prior to the assembly and operation
of the device.
These operating instructions are intended to make it easier for you to get familiar
with your device and utilise its intended possibilities of use.
The operating instructions contain important notes on how to work safely, properly
and economically with your machine and how to avoid dangers, save repair costs,
reduce downtime, and increase the reliability and working life of the machine.
In addition to the safety regulations contained herein, you must in any case comply
with the applicable regulations of your country with respect to the operation of the
machine.
Keep the operating instructions in a clear plastic folder to protect them from dirt and
humidity; store them near the machine. The instructions should be read and careful-
ly understood by each operator prior to using the machine. Only persons who have
been trained in the use of the machine and are aware of the related dangers and
risks should be allowed to use the machine. The local required minimum age must
be met.
In addition to the safety notes contained in these operating instructions and any
specific regulations in your country, the generally recognised technical rules for the
operation of identically constructed machines must be observed.
Introduction

Kapitelüberschrift
9
Layout (Fig. 1)
1. Spark protection
2. Adjusting screw for spark protection
3. Grinding disc
4. Workpiece support grinding disc
5. Star grip nut to mount/adjust the workpiece support grinding disc
6. Grinding disc cover
7. Protective hood grinding disc
8. On/Off switch
9. Engine housing
10. Upper (a) and lower (b) roller
11. Fixing screws for grinding disc cover
12. Grinding disc cover
13. Workpiece support grinding belt
14. Star grip nut to install the workpiece support grinding belt
15. Bore holes for table mounting
16. Protective hood grinding belt
17. Adjusting screw for belt run
18. Clamping lever grinding belt
19. Grinding belt
20. Working light
21. Fixing screws for grinding disc cover
Scope of delivery
Bench Grinder 1x
Spark protection 1x
Adjusting screw for spark protection 1x
Workpiece support 2x
Sanding belt (1x grit 80 pre-mounted, 1x grit 80, 1x grit 120) 3x
Warranty card 1x
Instruction manual 1x
Layout/Scope of delivery

Kapitelüberschrift
10
• Open the packaging and take out the equipment with care.
• Remove the packaging material.
• Check that all listed contents are present.
• Inspect the equipment and parts for any damage. Please contact the helpline if
anything is missing.
• If possible, keep the packaging until the end of the guarantee period.
• Read the operating instructions fully to familiarise yourself with the tool prior to
using it.
• Only use original accessories and spare parts. Spare parts are available by
contacting the helpline.
• Specify the part numbers when you contact the helpline.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic bags, film and small parts!
There is a risk of swallowing and suffocation!
Intended use
The bench grinder with belt sander is a stationary grinding device for the coarse and
fine grinding of metal, wood and plastic. It is suitable for deburring, rust removal and
grinding.
The device is not intended for all other types of applications (e.g. grinding with un-
suitable grinding tools,grindingwith a coolant solution,grindinghazardous mate-ri-
als such as asbestos).
The equipment is allowed to be used only for its prescribed purpose. Any other use is
deemed to be a case of misuse. The user/operator and not the manufacturer will be
liable for any damage or injuries of any kind resulting from such misuse.
An element of the intended use is also the observance of the safety instructions, as well
as the assembly instructions and operating information in the operating manual.
Persons who operate and maintain the product must be familiar with the manual
and must be informed about potential dangers.
Inaddition, the applicable accident preventionregulations must be strictlyobserved.
Other general occupational health and safety-related rules and regulations must be
observed.
The liability of the manufacturer and resulting damages are excluded in the event of
modifications of the machine.
Scope of delivery/Intended use

Kapitelüberschrift
11
The machine may only be operated with original parts and original accessories from
the manufacturer.
The safety, operating and maintenance specifications of the manufacturer, as well as
the dimensions specified in the operating manual, must be observed.
This equipment is intended for domestic DIY use only. We assume no guarantee if
the product is used in commercial or industrial applications, or for equivalent work.
Safety regulations
General power tool safety warnings
mWARNING Read all safety warnings, instructions, illustrations
and specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug
in any way. Do not use any adapter plugs with earthed (ground-
ed) power tools. Unmodifiedplugs and matching outlets willreduce
risk of electric shock.
Intended use/Safety regulations

Kapitelüberschrift
12
b) Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water enter-
ing a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use re-
duces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in
serious personal injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes,
hard hat or hearing protection used for appropriate conditions will
reduce personal injuries.
c) Prevent unintentionalstarting. Ensurethe switchis inthe off-po-
sition before connecting to power source and/or battery pack,
picking up or carrying the tool. Carrying power tools with your fin-
ger on the switch or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before turning the power
tool on. A wrench or a key left attached to a rotating part of the pow-
er tool may result in personal injury.
Safety regulations

Kapitelüberschrift
13
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep
your hair and clothing away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly
used. Use of dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you
to become complacent and ignore tool safety principles. A care-
less action can cause severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and
off. Any power tool that cannot be controlled with the switch is dan-
gerous and must be repaired.
c) Disconnect the plug from the power source and/or remove the
battery pack, if detachable, from the power tool before making
any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the pow-
er tool accidentally.
d) Store idle power tools out of the reach of children and do not al-
low persons unfamiliar with the power tool or these instructions
to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools and accessories. Check for misalignment or
binding of moving parts, breakage of parts and any other condi-
tion that may affect the power tool’s operation. If damaged, have
the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are eas-
ier to control.
Safety regulations

Kapitelüberschrift
14
g) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and
the work to be performed. Use of the power tool for operations differ-
ent from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil
and grease. Slippery handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected situations.
5) Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of
the power tool is maintained.
Safety instructions for grinding machines
a) Do not use damaged accessories. Check the accessories, e.g. the grind-
ing disc for cracks before each use. After inspection and installation of
an accessory, remove yourself and bystanders from the machine and
allow the electric tool to run at maximum idle speed for one minute.
Damaged accessories normally break during this test period.
b) The nominal speed of the accessories must be at least equal to the
maximum speed indicated on the electric tool. Accessories that run fast-
er than the nominal speed may break.
c) Never grind on the sides of a grinding disc. Lateral grinding can cause
the grindstone to break.
Residual Risks
mThe machine has been built according to the state of the art and the rec-
ognised technical safety requirements. However, individual residual risks can
arise during operation.
• Risk of injury for fingers and hands due to the rotating grinding tool.
• Hazard due to electrical power, with the use of improper electrical connec-
tion cables.
• Furthermore, despite all precautions having been met, some non-obvious
residual risks may still remain.
• Residual risks can be minimised if the “safety instructions” and the “intend-
ed use” are observed along with operating manual in its entirety.
Safety regulations

Kapitelüberschrift
15
Assembly
m WARNING
Always pull out the mains plug before carrying out adjustments on the device.
Spark protection assemble/set (Fig. 2)
• Screw the spark protection (1) using the adjusting screw (2) and the nut on to the
protective hood (7). To do so you will need a screwdriver and a ring spanner (AF 8
mm / not included), used to hold it in place.
• Set the spark protection (1) with the adjusting screw (2) so that the distance be-
tween the grinding disc (3) and the spark protection is max. 2 mm (see small im-
age).
mATTENTION
Periodically readjust the spark protection in order to offset the wear and tear
of the grinding disc and the spark protection is max. 2 mm.
Workpiece supports assemble / set (Fig. 3+4)
• Screw the workpiece supports (4/13) on to the device. Two positions are possible for
the tape loop (see fig. 3 / Pos. A + B).
• To do so, use the screws (5/14), washers, toothed lock washer and star grip nuts
provided.
• Set the workpiece support of the grinding belt (4) with the star grip nut (5) so that
the distance between the grinding disc (3) and the workpiece support is max. 2 mm
(see small image).
mATTENTION
Periodically readjust the spark protection in order to offset the wear and tear
of the grinding disc and the spark protection is max. 2mm.
Screw device on to workbench (Fig. 5)
• Screw the device onto the workbench with 4 screws and nuts. Insert the screws
through the 4 bore holes (15) on the base of the device. The screws and nuts re-
quired for assembly are not part of the scope of delivery.
Safety regulations/Assembly

Kapitelüberschrift
16
Operation
mATTENTION
-Always make sure the device is fully assembled before commissioning!
-Always disconnect the plug from the mains socket before working.
-Use only grinding disks and accessories recommended by the manufacturer.
The use of other insertion tools and other accessories may cause risk of injury.
-Only use grinding tools which bear information about the manufacturer, type of
binding, dimension and permitted number of revolutions.
-Only use grinding discs where the printed rotational speed is at least as high as
what has been specified on the name plate of the device.
-Do not use broken, cracked or other-wise damaged grinding disks.
-Never operate the device without the visual protection disk.
-Always use protective goggles even if you are protected against sparks.
-Always inspect the grinding disc before starting the device: Check the distance
between the spark protection and grinding disc as well as workpiece support
and grinding disc (distance maximum 2 mm).
-The grinding disc must be replaced once the spark protection and workpiece
support on the grinding disc do not have distance of max. 2 mm.
-Switch on the equipment only whenit is safely installed on the work surface.
mATTENTION
Keep your hands away from the grinding disc and grinding belt when the de-
vice is in operation. Injury hazard!
mATTENTION! It is recommended that the tool always be supplied via a residual
current device having a rated residual current of 30mA or less.
Switching on and off
• To switch on, press the “I” on switch (8) and the device starts up and the working
light begins to shine.
• To switch off, press the “0” off switch (8) and the device switches off and the work-
ing light goes out as a result.
After switching on the device, wait until the device has reached its max. speed. Only
then must you start the grinding.
Operation

Kapitelüberschrift
17
mATTENTION
The disk will continue to run after the equipment is switched off. There is a risk
of injury.
Test run:
Before starting work and after each change of grinding disk, carry out a test run of at
least 60 seconds with no load. Switch off the equipment immediately if the disc runs
lumpy, substantial vibrations occur, or abnormal noises are generated.
Working instructions
Grinding with the grinding disc
mATTENTION
Fold down the spark protection (1) when grinding in order to avoid injury from
sparks.
NOTE: The arrow on the protective hood (7) shows the direction of rotation of the
grinding disc.
• Place the workpiece on the workpiece support (4) and slowly bring it to its desired
angle on the grinding disc (3).
• Move the workpiece slightly from side to side in order to achieve an optimal grind-
ing result. This way, the grinding disc is worn uniformly. Occasionally, allow the
workpiece to cool down.
Tape loops
NOTE: The arrow on the protective hood (16) shows the direction of rotation of the
grinding belt.
• Firmly hold the workpiece, do not exert any strong force.
• Move the workpiece slightly from side to side in order to avoid a one-sided wear of
the grinding belt.
• Always grind the pieces of wood in the direction of the wood grain in order to avoid
chipping.
Change grinding belt (Fig. 6)
• Loosen the 2 fixing screws (11) and hang out the grinding belt cover (12).
• Press the clamping lever (18) downwards and detract the grinding belt (19).
• Place the new grinding belt (19) in the centre on the upper (10a) and lower (10b)
rollers.
• Push the clamping lever grinding belt (18) and mount the grinding belt cover (12).
Operation/Working instructions

Kapitelüberschrift
18
Set the tape run
• The tape run accuracy is set by turning the adjusting screw for belt run (12).
• Check the tape run by manually turning the grinding belt.
Change grinding disc (Fig. 7)
Information on replacement:
-Never operate the device without protective equipment.
-Ensure that the rotation speed stated on the grinding disc (3) is the same or
higher than the nominal rotation speed of the device.
-Ensure that the grinding disc dimensions match those of the device.
-Only use flawless grinding discs (ringing test: when you strike the grinding disc
with a plastic hammer, it results in a clear sound).
-Never re-drill a locating hole which is too small to make it larger.
-Never use separate bushings or adapters in order to make grinding discs whose
hole is too large fit the device.
-Do not use any saw blades.
-To clamp the grinding tools only use the clamping flange provided. The pads
between the clamping flange and the grinding tools must be made of elastic
materials e.g., rubber, soft cardboard etc.
-Always reassemble the device completely after replacing the grinding disc.
mATTENTION
Switch the device off and remove the mains plug. Allow the device to cool down.
Wear protective gloves when changing the grinding discs in order to avoid cut-
ting risk.
• Remove the spark protection (1) (see “Assemble/set spark protection).
• Loosen the 3 fixing screws (21) and remove the grinding disc cover (6).
• Loosen the fixing screws (11) and remove the grinding belt cover (12) (see “Changing
the grinding belt“).
• Unscrew the grinding disc nut (3a) in the clockwise direction, by holding the nut of
the opposite roller of the grinding belt in place (see small image). Hold it tight with a
19mm socket wrench or pliers (not included).
• Remove the clamping flange (3b) and the grinding disc (3).
• Set up the new grinding disc (3) and the clamping flange and manually screw the
grinding disc nut (3a) in the anti-clockwise direction.
• Screw the grinding disc cover (6).
• Set the spark protection (1) and the workpiece support (4) so that the distance be-
tween the grinding sic (3) is max. 2 mm (see “Assembly”)
Working instructions

Kapitelüberschrift
19
The grinding disc nut must not be screwed too tightly in order to avoid a breaking of
the grinding disc and nut.
Test run:
Before starting work and after each change of grinding disk, carry out a test run of at
least 60 seconds with no load. Switch off the equipment immediately if the disk runs
lumpy, substation vibrations occur, or abnormal noises are generated.
Cleaning and maintenance
Always pull out the mains power plug before starting any cleaning work.
Have any work not described in these instructions carried out by a specialist work-
shop. Use only original components. Allow the equipment to cool before carrying out
any maintenance and cleaning work. There is a risk of burns.
Before each use, check the equipment for obvious defects such as loose, worn or dam-
aged components and check that screws or other parts are sitting correctly. In par-
ticular, check the grinding disk (3). Replace damaged parts.
Cleaning
• Keep all safety devices, air vents and the motor housing free of dirt and dust as far
as possible. Wipe the equipment with a clean cloth or blow it with compressed air at
low pressure.
• We recommend that you clean the device immediately each time you have finished
using it.
• Clean the equipment regularly with a moist cloth and some soft soap. Do not use
cleaning agents or solvents; these could attack the plastic parts of the equipment.
Ensure that no water can seep into the device.
Maintenance
The device is maintenance-free.
Attention! If the replacement of the supply cord is necessary, this has to be done
by the manufacturer or his agen in order to avoid hazards.
Caution, risk of electic shock! The light source in this luminaire shall only be re-
placed by the manufacturer or his service agent or a similar qualified person.
Working instructions/Cleaning and maintenance

Kapitelüberschrift
20
Service information
Please note that the following parts of this product are subject to normal or natural
wear and that the following parts are therefore also required for use as consumables.
Wear parts*: Grinding disc, grinding belt.
* Not necessarily included in the scope of delivery!
Technical data
Rated voltage 230-240 V~
Rated input 240 W
Protection class I
Protection category: IPX0
Idling speed 2980 min-1
Grinding disc dimension Ø150 x 20 x 12.7 mm
Grinding disc granulation 36
Grinding disc velocity 35 m/s
Grinding belt dimension 686 x 50 mm
Grinding belt granulation 80 / 120
Grinding belt velocity 15 m/s
Weight 7 kg
Noise
Sound and vibration values were measured in accordance with EN62841.
Sound pressure level LpA 86.6 dB(A)
Uncertainty KpA 3 dB
Sound power level LWA 99.6 dB(A)
Uncertainty KWA 3 dB
Cleaning and maintenance/Technical data

Kapitelüberschrift
21
Wear ear-muffs.
Excessive noise can result in a loss of hearing.
The above-mentioned noise emission values were measured in accordance with a
standardised test procedure and can be used to compare one power tool with an-
other.
The specified device emissions values can also be used for an initial estimation of the
load.
Warning:
• The noise emission values can vary from the specified values during the actual use
of the electric tool, depending on the type and the manner in which the electric tool
is used, and in particular the type of workpiece being processed.
• Try to keep the stress as low as possible. For example: Limit working time. In doing
so, all parts of the operating cycle must be taken into account (such as times in
which the electric tool is switched off or times in which it is switched on, but is not
running under a load).
Storage and transport
Store the equipment and accessories out of children’s reach in a dark and dry place at
above freezing temperature. The ideal storage temperature is between 5 and 30 °C.
Store the electric tool in its original packaging.
Grinding disks must be stored dry and upright and are not to be stacked.
mATTENTION Unplug the machine!
The appliance must unconditionally be secured against falling or turning down dur-
ing transport.
The appliance can be lifted on the frame.
Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit.
The raw materials in this packaging can be reused or recycled. The equipment and
its accessories are made of various types of material, such as metal and plastic. Never
place defective equipment in your household refuse. The equipment should be tak-
en to a suitable collection center for proper disposal. If you do not know the wherea-
bouts of such a collection point, you should ask in your local council offices.
Technical data/Storage and transport/Disposal and recycling

Kapitelüberschrift
22
Troubleshooting
The table below contains a list of fault symptoms and explains what you can do to
remedy the problem if your equipment fails to work properly. If the problem still
persists after working through the list, please contact your nearest service
workshop.
mIMPORTANT!
Hint in case of sending the equipment to a service centre:
Problem Possible cause Action
Device doesn‘t start
Mains voltage missing
Main circuit breaker is tripped
Check the socket, mains cable, line,
mains plug, repairs to be carried
out by qualified electrician if neces-
sary, check main circuit breaker.
On/off switch may be defective Repair by Customer Care
Engine faulty
Grinding tools do not
move although the
engine is running
Grinding disc nut loose Tighten grinding disc nut (see
“Changing the grinding disc“)
Grinding belt loose Re-mount grinding belt (see
“Changing the grinding belt“)
Drive is blocked
Grinding belt blocking drive Re-mount grinding belt (see
“Changing the grinding belt“)
Workpiece, remaining work-
pieces or remaining grinding
tools block drive Remove blockages
Engine is slower and
stops Device is overloaded through workpiece
Reduce pressure on grinding tool
Workpiece unsuitable
Grinding disc does
not rotate smoothly,
abnormal noises can
be heard
Grinding disc nut loose Tighten grinding disc nut (see
“Changing the grinding disc“)
Grinding disc faulty Change grinding disc
Spark protection or work-piece
support set incorrectly Set spark protection or work-piece support (see “Assembly“)
Bad grinding output Grinding belt worn Change grinding belt
Troubleshooting

Kapitelüberschrift
23

BENCH GRINDER
Warranty Details
The product is guaranteed to be free from defects in workmanship and parts for a period of 36
months from the date of purchase. Defects that occur within this warranty period, under normal
use and care, will be repaired, replaced or refunded at our discretion.The benets conferred by this
warranty are in addition to all rights and remedies in respect of the product that the consumer has
under the Competition and Consumer Act 2010 and similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
3
YEAR
WARRANTY
AFTER SALES SUPPORT
 1300 855 831 [e-mail]
AU Hotline Costs: Local rate for landline calls*
*Charges may vary dependent upon network operator or mobile network provider.
TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION