FETtec FC F7 User manual
Page 1
FETtec FC F7
Manual
Page 2
Introduction..................................................................................................................................3
Features.......................................................................................................................................3
Safety warning .............................................................................................................................4
Recommended steps for installation of the FETtec FC F7...........................................................4
Connection Diagram ....................................................................................................................5
Connection layout top...............................................................................................................5
Connection layout bottom.........................................................................................................6
FETtec FC F7 version 1.2 ........................................................................................................7
ESC connection diagram .............................................................................................................8
ESC connection via 8 pin connector.........................................................................................8
Receiver connection (RX)............................................................................................................9
TBS Crossfire...........................................................................................................................9
Crossfire nano connection....................................................................................................9
SBUS receiver / FrSky R-XSR ...............................................................................................10
VTX connection (Unify nano).....................................................................................................11
Camera connection....................................................................................................................12
Resetbutton................................................................................................................................12
FC configuration.........................................................................................................................13
KISS FC Firmware..................................................................................................................13
FETtec Alpha FC firmware .....................................................................................................14
Get back to KISS ................................................................................................................17
Firmware updates on FETtec Alpha FC firmware ...............................................................19
Settings in FETtec Alpha FC firmware................................................................................20
Display connection.....................................................................................................................21
Dimension (in mm).....................................................................................................................22
Page 3
Introduction
Thank you for purchasing the FETtec FC F7. This is a KISS licensed F7 Flight-controller
Features
•KISS FC v2 firmware (FETtec Alpha FC firmware flashable)
•F7 Processor
◦STM32F7RET6 @ 216MHz
◦MPU6000
•Supply voltage 6-27V (2S-6S Lipo)
•Dedicated onboard 5V BEC for VTX (max 600mA)
•8 pin connector for solder free ESC connection
◦Connector 1: ESC signal 1-4, telemetry, VCC, GND
◦Connector 2: ESC signal 5-8 (depending on UAV type 1-4), telemetry, VCC, GND
•5 UART serials
◦UART 1 free
◦UART 2 used for Receiver
◦UART 3 free
◦UART 4 used for onboard OSD, can be set free
◦UART 5 used for ESCs / TLM / Onewire
•Build-in real Pit-Mode for unify nano (via VTX Pin and 5V on SER1)
•4 ESC solder pads (Signal/GND) in each corner
•Direct places for RX and VTX (unify nano, CRSF nano, FrSky R9)
•Buzzer pads
•Supported ESC protocols
◦PWM, Oneshot125, Oneshot42, Dshot150/300/600/1200/2400, FETtec Onewire
•Dimensions 35x30mm without 30x30 corners
◦20x20mm (with breakable holes M2 to M3)
◦30x30mm hole distance useable (breakable 30x30mm corners)
•Overall height: 7,9mm
•Weight: 5,37g
•Connector type: JST-SH-1mm
Page 4
Safety warning
•Remove propeller before flashing and configuration
•always flash latest firmware before operation
Recommended steps for installation of the FETtec FC F7
•Connect to FETtec Configurator and update to the latest firmware (see FC firmware
update)
•Install the FC in your copter (see Connection diagrams for correct wiring and installation)
•Make sure everything is connected properly and check without propellers
•Connect to FETtec Configurator to proceed with final configuration of the FETtec FC F7
Page 5
Connection Diagram
Connection layout top
6 pin connector (SER1):
•RX1: for digital FPV systems or other functions configurable in GUI (same for VCS/TX3)
•TX1: for smart audio / tramp configuration or TX for digital FPV systems
•RGB LED: PWM signal pin to control WS2812 LEDs or similar (configurable in GUI)
•BAT+: Battery voltage
•VTX 5V
•GND
Signal1-4 –Motor Signal 1-4
ESCTLM –Telemetry (Serial)
GND –Reference Signal Ground
UPRT –Receiver signal port (SBUS / F-Port / PPM / Crossfire TX)
RXTLM –Receiver telemetry (sPort / Crossfire RX)
Serial connectors (SER1&SER3) are JST-SH-1mm 6-pin
Page 6
Connection layout bottom
8 pin ESC connector:
•BAT+: Battery voltage out to supply FC power
•GND
•ESCTLM/Onewire: ESC Telemetry signal to FC or Onewire signal pin (depending on
configuration)
•Signal 1-4: ESC signal output for each ESC
Receiver connector:
•UPRT: Receiver signal to FC (see page 10 receiver connection diagram for further
information)
•RXTLM: Telemetry signal to receiver (see page 10 receiver connection diagram for
further information)
•5V
•GND
6 pin connector (SER3):
•RX3: function configurable in GUI
•TX3: function configurable in GUI
•3,3V
•VCC: Battery voltage
•5V
•GND
Page 7
FETtec FC F7 version 1.2
Page 8
ESC connection diagram
ESC connection via 8 pin connector
For easy ESC connection via 8 pin cable
FETtec FC F7 to FETtec 4in1 ESC 35A (same for FETtec 4in1 ESC 45A), cable included with
FETtec ESCs.
Any other ESC is usable (please make sure the signal pinout is correct, otherwise change
accordingly
Page 9
Receiver connection (RX)
Top & Bottom connectors for receivers (bottom connector JST-SH-1mm 4-pin)
TBS Crossfire
Crossfire nano connection
cable connection 2,54mm pinheader connection
Page 10
SBUS receiver / FrSky R-XSR
Page 11
VTX connection (Unify nano)
Page 12
Camera connection
Notes:
•RX and TX connection is only for cameras that support serial
•5V (U5V) and Video (UVID) are only for use with a mounted unify PRO nano or unify
PRO nano 32
Resetbutton
Resets the FC to the preflashed bootloader
Page 13
FC configuration
KISS FC Firmware
For the latest KISS FC firmware and GUI please visit https://github.com/flyduino
•Install KISS GUI
•Connect COM port
•To update the FETtec FC firmware please use the KISS GUI and choose FETTEC KISS
FC
•Configuration can be made in the KISS GUI, settings are in the advanced tab
Page 14
FETtec Alpha FC firmware
The FETtec FC F7 is compatible with FETtec Alpha FC firmware.
1. Open FETtec Toolset https://gui.fettec.net and choose ALPHA Configurator.
2. Connect the FETtec FC via USB.
3. Open the ALPHA Configurator and select open port. Choose the serial port on which the
FC shows up and press connect.
4. If you have KISS FC firmware running on your FC, you will get a warning if you want to
flash FETtec Alpha FC firmware. Press “OK”
Select serial port again
Page 15
5. “Select new firmware to flash”.
We always recommend flashing the latest available firmware.
6. Confirm to flash FETtec ALPHA firmware by pressing “OK”
Page 16
7. FC firmware update is done!
The FC needs a restart after that, therefore the com port is requested to be selected and
connected again
Now you can customize everything in the GUI according to your wishes.
Please connect everything like described in the manual of the FC.
The receiver signal will get auto detected (supported systems are Frsky Sbus+S-Port, CRSFv2
and CRSFv3 and Ghost).
Page 17
Get back to KISS
If the FETtec Alpha FC firmware is flashed on your FC and you want to get back to KISS
firmware, follow these steps:
1. Open FETtec Toolset https://gui.fettec.net/
2. Connect the FETtec FC via USB.
3. Press the reset button once
4. Open the FETtec ESC Configurator and select “USB” and connect.
5. Choose the serial port on which the FC shows up and press connect.
6. Now the FC shows up and you can select KISS Firmware (FETtec FC G4 1.3-RC47m) in
“Remote Firmware” and press “Flash selected!”
Page 18
7. Flashing to KISS FC firmware done.
Page 19
Firmware updates on FETtec Alpha FC firmware
For firmware updates it is the same procedure as flashing the FETtecAlpha FC firmware.
Connect FC via open port and choose “Firmware”.
Now you can flash the latest firmware update via “Select new firmware to flash” or choose
“Flash local file”.
We always recommend to use the latest available firmware to get the best user experience.
If you like to try new features and firmware developments you can join our Discord channel to
be always up to date (https://discord.gg/pfHAbahzRp).
Table of contents
