FG Flight T53 User manual

Thank you for purchasing this Flying Gadgets product, please read this manual carefully before
use and retain it for future reference.
1.The coaxial-rotor design and built-in gyro are used to increase the helicopter’s
stability, making it the perfect choice for beginners.
2.By using new infra-red auto connection technology users can operate three
helicopters simultaneously.
3.On a full battery charge, the helicopter can fly for approx 9 minutes.
4.The triple circuit protection the flight improves the service life of the helicopter.
5.The camera has a built in microphone and can either take video or photo
1. Please read this instruction manual carefully before using this product
and operate it according to the instructions.
2. Keep small parts away from children.
3. Keep the batteries away from fires and high temperatures.
4. When flying the helicopter keep it a minimum of 1-2 metres away from
yourself and others to avoid injjury.
5. Do not modify or take this product apart.
6.Keep the helicopter at all times in your sight whilst flying.
7. Always make sure children are supervised by an adult whilst using the
helicopter.
8. Only use recommended batteries in the product.
9. Insert the batteries in the correct polarity.
10. Do not recharge non rechargable batteries.
11. Do not mix old and new batteries.

away from
uses in
Turn the remote control “OFF” before operating.
Make sure the helicopter is on a flat stable surface.Turn the helicopter on by the power switch.
The searchlight on the front of the helicopter will blink rapidly. After a few seconds the
searchlight will blink slower, this indicates that the helicopter is ready to connect to the remote
control.
Then select “A”, “1” or “2” on the front of the remote control. Then turn on the power switch on
the remote control. Push the left hand power stick to the top of the controller then to the
bottom, the red light on the controller will blink. As soon as the helicopter is connected the red
light on the controller will remain on and will not blink.
Select channel 1 and channel 2 and operate a maximum of 2 helicopters simultaneously.
Only use one helicopter per channel at the same time.
Connect the helicopters one by one.
Once you turn off the helicopter or controller power you will have to
reconnect.
Select channel A if you are using only one helicopter.

Push the left control
stick up, and the
rotation speed of the
main rotor increases
and the helicopter
ascends
accordingly.
Push the left control
stick down, and the
rotation speed of the
rotor decreases and
the helicopter
decends accordingly.
When the helicopter is in
the air, turn the control
stick to the left, the
helicopter will spin to the
left.
When the helicopter is in
the air, turn the control
stick to the right, the
helicopter will spin to the
right.
When the helicopter is
in the air, push the
control stick on the right
up, the helicopter will
move forward.
When the helicopter is in
the air, push the control
stick on the left down,
the helicopter will move
backwards.
If the helicopter keeps spinning in the air without any control movement, you can correct
this by adjusting the trimmer on the remote control.
If the helicopter is spinning counter
clockwise, move the gyro regulation button
to the right until the helicopter stops
spinning.

If the helicopter is spinning clockwise
move the gyro regulation button to the left
until the helicopter stops spinning.
The red power light on the remote control will start to blink fast when the battery
voltage drops below a certain level in the helicopter. The helicopter can be out of
control. Recharge the helicopter to correct.
To protect the motor and prevent any damage when the main rotors become jammed.
The main rotors will auto cut off. When this happens for 3 seconds the helicopter
searchlight will blink rapidly. Pull the left hand power stick on the controller to its lowest
The C4003 camera (purchased seperately) can be installed in this helicopter.
How to install the camera
1.Install the camera to the bottom of the helicopter and screw it in. Pic.6 and 7
2.Insert the camera plug in to the video socket on the PCB of the helicopter. (Pic.8)
Camera control
1. Insert the TF memory card into the camera module on the helicopter then turn on the
helicopter. Once the helicopter is on a red and green will flash on the camera module.
Around two seconds later, the lights will stop flashing and remain “ON” it is now ready.
2. When the helicopter is connected to the controller the indicator lights on the camera module
will remain “ON”.
To take video move the switch on the camera in the the direction of the video icon (Pic. 9),
and then turn on the camera switch on the remote control, it will start taking video and
the red light on the camera module will flash. Press the camera button again on the controller
and you will stop taking video
To take photos move the swith on the camera in the direction of the photography icon (Pic. 10),
and then press the camera button on the remote control to take photos.
3. After you have finished filming, take the TF memory card out of the camera module and insert
it into the USB card reader, then insert the USB reader into the USB input on your the computer to
download the video.

TIPS
To stop filming, please press the camera button on the remote control. If you
unplug the battery cable or take out the TF memory card from the camera module it
will result in the loss of the video data.
To avoid helicopter crashing,please do not insert or take out the TF memory card from
the camera module,whilst the helicopter is on. The TF memory card should be installed
before the helicopter is on and taken out only when off.
If you crash turn the helicopter off and then turn back on to recover the helicopter.
When the red light and the green light on the camera keep flashing
alternately, it means that the TF memory card is not inserted or the TF memory card is
damaged. It is possible to restore the memory card by reformatting(Take out the TF
memory card, then, insert it into the USB card reader, then, connect it to the computer
and reformat the memory card)
If the red light remains "ON" this indicates insufficient memory.
1. Use a wet cloth to clean this product.
2. Avoid exposure to sunlight and extreme temperatures.
3. Do not soak in water.
4. Switch off the remote control and the helicopter when not using.
5. Batteries should be taken out of the controller when not being used for some time.
6. Use all new alkaline batteries for the helicopter to have the best performance.
7. Periodically check the plugs and other parts of the helicopter for damage. If
damage is found do not use until it has been repaired.
The channel of the
controller is not the same
as the helicopter.
Charge the helicopter battery.
controller.
Unable to
control the
helicopter
correctly
1. Too much sunlight.
2. Another Controller nearby is
on the same frequency.
Choose a better place out of
direct sunlight.
Change the switch on the
controller to a different infra red
channel.

When the controller/helicopter is underpowered, the control distance is shorter.
If the helicopter is underpowered it may have difficulty taking off.
If the helicopter becomes damged then repair it. If you fly it damaged then it could be out of control and
cause an injury.
If you do not play with the helicopter for some time then remove the batteries in the controller as they
can leak and damage the product.
Make sure to not crash the helicopter from a high altitude as it will damage it.
* Users are responsible for preventing injuries to
people or propery when using this helicopter
* Users should follow the instructions provided
* Ensure a safe distance between you and the
helicopter when using it to avoid injury
* The manufacturer and distributer are not
resposible for damage caused by misuse
* This product is not suitable for those under 14
years of age
* Follow the guidelines provided to assemble the
helicopter. Small parts should be assembled by
an adult
* This product contains small parts. Please guard
against eating and causing a choking hazard.
Keep away from children
* Do not play with this item near a road or
swimming pool, lake etc
* Keep a regular check on the charger and all
parts of the helicopter. If there is any damage to
them then stop using it.
* Remove all packaging to avoid damage
* The charger must be connected to the proper
voltage as indicated
* The charger is not a toy
* Do not dissemble the wire on the landing gear-
this is the receiver.
* Disconect the helicopter when cleaning
* Do not point the antenna at your or others
faces or eyes
* Use either AA non rechargable or
rechargable batteries
* Non rechargable batteries should not be
recharged
* Chargable batteries must be charged by an
adult
* Only batteries recomended should be used
* Batteries must be insterted correctly and
with the right polarity
* Exhausted batteries should be removed
* The supply terminals are not to be short
circuted
* Do not short circuit or unwrap the battery.
* Avoid any contact with fire.
* Do not mix old and new batteries
* Do not mix different types of batteries
* Remove the batteries when not in use
* Photos are for reference only- the
appearance of the product might differ from
the photos
* Please retain this information for future use