FIA GS900 Series User manual

GS900 Series –Summer Bug Screen
INSTALLATION INSTRUCTIONS
Before installing Stick A Stud TM *D* fasteners, please note:
Clean area with isopropyl alcohol swab (supplied)
Surface must be completely dry, wax free with no cleaning fluid present.
For best results, install at temperatures over 60oF (16oC). Ensure that the
surface of the vehicle is warm to the touch. Use a hair dryer to warm up the
surface and the Stick A Stud™ *D* if necessary.
The base of the Stick A Stud™ *D* can be shaped by bending or folding along the
indented lines
FOR CONCAVE OR CONVEX SURFACES FOR ANGLED SURFACES
In some instances the Stick A Stud TM *D* fastener’s base may require trimming. Simply cut
as required
INSTALLATION:
1) Snap all Stick A Stud TM *D* fasteners to the bug screen while ensuring the protective
backings remain intact.
2) Position the bug screen on the vehicle and note where each Stick A Stud TM *D*
fastener will be located to ensure there will be maximum surface contact at each
installation point.
3) Temporarily fasten the bug screen with masking tape to the vehicle.
4) Remove protective backing from a corner Stick A Stud TM *D* .Avoid touching
adhesive.
5) Apply firm pressure for 10 seconds.
6) Apply the next Stick A Stud TM *D* fastener ensuring that no stress is applied to other
fasteners when installing the bug screen. CAUTION: A MINIMAL AMOUNT OF
STRESS ON THE BUG SCREEN FROM SIDE TO SIDE AND TOP TO BOTTOM IS
RECOMMENDED. EXCESSIVE STRESS WILL CAUSE IMPROPER
INSTALLATION.
7) Attach remaining Stick A Stud TM *D* fasteners along top and bottom.
8) Carefully remove bug screen and again apply firm pressure to each Stick A StudTM *D*
fastener. INSTANT BOND CAN BE INCREASED BY USING HAIR DRYER ON
HIGH FOR 2-3 MINUTES ON EACH INSTALLED STUD.
9) Allow a minimum of 24 hours before use. See chart on reverse.
Peel away Stick-a-StudTM
fasteners protective backing
Adhere Stick-a-StudTM
fasteners to vehicle Snap on Winter Front
or Bug Screen

BOND STRENGTH
Additional Stick A Stud TM *D* fasteners are available; part number HK104
They are also available in white; part number HK104-WHITE
Kits with studs and screws are also available; part number HK103
NOTES
-Models requiring adhesive hook and loop fastener installation:
Step 1 -BEFORE APPLYING HOOK AND LOOP FASTENER:
- Ensure the area where hook and loop fastener strips are to be attached is
clean and dry.
- Remove protective backing
- Secure in place by pressing firmly on hook and loop fastener
Step 2 - : Attach adhesive backed hook and loop fastener strip to the underside of
the grill frame to line up with hook and loop fastener on bug screen. On some
vehicles the adhesive backed hook and loop fastener strips require mounting on
the front of the grill frame or under the hood on the radiator frame.
-Models requiring attachment to grill face and bumper for installation:
GS901-24, GS904-6, GS906-7, GS907-3, GS907-34, GS909-34, GS909-48
-Models requiring attachment to the top of the grill frame under the hood and to the
bumper: GS905-7, GS907-32, GS907-33, GS909-45
- Models requiring attachment to the hood: GS901-17, GS901-19, GS901-20, ,
GS901-21, GS901-27, GS903-4, GS905-42, GS909-281, GS909-46
- Models requiring attachment to grill face and to top of the grill frame under the
hood: GS901-15, GS901-16, GS901-22, GS902-9, GS904-11, GS904-12, GS904-7,
GS904-8, GS905-6, GS905-71, GS906-81, GS906-9, GS907-4, GS908-2, GS909-22,
GS909-26, GS909-361, GS909-42, GS909-43
-On some models there are more domes than are required for installation. Align
unit with grill to determine which domes are required.
TIME
BOND
20 minutes
50%
60 minutes
75%
24 hours
90%
72 hours
100%