FIBARO FGIC-001 User manual

Installation & Configuration Guide
INTERCOM
SMART VIDEO DOORBELL
www.domotica-shop.nl

Important safety information
Read this manual before attempting to install the device!
Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer, Fibar
Group S.A. will not be held responsible for any loss or damage resulting from not following the instructions of operating manual.
The manufacturer is not responsible for any accidents related to theft, damage or breaching of the wiring, performed by an unauthorized
person.
The device is not designed to protect the owner’s property. It is recommended to use a professional alarm system for such solution.
Make sure that local law does not prohibit to record, store, and edit the video without the consent of people being recorded.
It is strongly prohibited to connect any of the device terminals to mains (110V/230V) voltage! It is designed to be powered with low volt-
age power supply. Connecting to the mains power will result in damaging the device and will void the warranty.
To be installed only by a qualied specialist! Performing the installation or maintenance on your own may void the warranty.
Please note that the usage of cellular data may cause additional charge.
Caution HOT!
Inside the operating device there are elements that may cause burns.The device may be demounted at least 30 minutes after
disconnecting the power supply. We recommend to still watch for elements marked as“Caution hot”.
!
www.domotica-shop.nl

CONTENTS
Description and features
Installation
Package contents
Required equipment
Choosing location
Choosing and routing wires
Mounting the installation box
Mounting the in-wall part
Connecting wires
Mounting the on-wall part
SD Card
Conguration
Requirements
First login
Creating home
Conguration of the rst device
Connecting to the network
User conguration
Adding more devices
User roles
Inviting users
Resetting to factory settings
Device operation
Use cases
Specications
Regulations
Warranty terms and conditions
4
5
5
6
7
8
10
11
12
15
16
17
17
18
19
19
20
21
22
22
23
24
25
26
28
29
30
www.domotica-shop.nl

4DESCRIPTION AND FEATURES
Description and features
Description
FIBARO Intercom can show you everyone who has arrived at your doorstep with a 180-degree high-denition view and night vision.
This modern-looking, high-gloss device can be placed near the front door or gate to look after your safety.
The Intercom allows to control two gates, which might be opened using assigned PIN codes on rotating ring, holding up a phone towards
the device or using dedicated app to do it remotely.
The recordings can be stored on a SD card.
Main features
• Rotating ring used for PIN codes,
• Two relay outputs (to control gates),
• Full HD video resolution (1080p/30fps),
• Ultra-wide angle lens (180o),
• IR illumination (for night view),
• Noise-canceling microphones,
• Speaker,
• Proximity sensor.
Before installing the device
1) Check if the package content is complete,
2) Prepare all the required equipment,
3) Make sure the power is o.
www.domotica-shop.nl

5INSTALLATION -PACKAGE CONTENTS
On-wall part In-wall part
Installation box Tightening tool
Mounting screws Hex key 0.9mm
2.2mm x 12mm M2 x 8mm
DIN 913 hex
Installation
Package contents
www.domotica-shop.nl

6INSTALLATION -REQUIRED EQUIPMENT
Required equipment
Wire stripper Needle-Nose Pliers or Tweezers
PH0 and PH1 Phillips Screwdrivers Professional equipment for mounting
the installation box depending on the
type of construction material
www.domotica-shop.nl

7
INSTALLATION -CHOOSING LOCATION
Choosing location
Recommended height of installation: 160 cm
Do not install the device in direct sunlight!
If this happens, try to shade the device to avoid overheating and to keep the sun
othe lens and reduce are.
Long-term operating in direct sunlight may cause overheating of the device, its
malfunctioning, and a signicant temperature rise of a housing above the limit of
safe operation for the user.
Do not mount the device in places exposed to rain or water drop, or prone to
ooding.
Surface around the installation box should be perfectly smooth to ensure align-
ing the device with the wall.
www.domotica-shop.nl

8INSTALLATION -CHOOSING AND ROUTING WIRES
Choosing and routing wires
The device may be powered in two ways:
1) Power supply 12V DC (+/- 10%) 1A LPS (not included)
2) PoE (Power over Ethernet) PSE 48V
Both powering modes work in parallel and may be connected at the same time with no eect on the device operation.
The device may be connected to network in two dierent ways:
1) Ethernet - wired connection (recommended)
2) Wi-Fi - wireless connection
Wired connection is recommended, but if you decided to use Wi-Fi connection make sure that the device will be in range of your
router and have a good quality connection.
Before routing the wires make sure what you want to connect and how many wires you will need:
1) Power supply 12V DC - used to power the device with external power supply.
Wires required: 2
2) Ethernet - used for communication with the device and can be also used to power it using PoE Power over Ethernet.
Wires required: 1 twisted pair cable with 8 wires
3) Built-in relays - can be used to open 2 gates or doors with an electric lock (via app, BLE proximity function, PIN code or physical buttons).
Wires required: 2 wires per one gate/door
4) Two buttons for built-in relays - can be used to control built-in relay using physical buttons, switches etc.
Wires required: 1 wire per one button and 1 wire for common ground
5) Tamper - can be connected to an external system to alarm it in case of sabotage attempt.
Wires required: 2
i
www.domotica-shop.nl

9
INSTALLATION -CHOOSING AND ROUTING WIRES
When routing wires take into consideration:
• The installation wires of the unit must be lead separately from the mains power wires to prevent the transmission interference and
overvoltage on the control lines.
• Wires inside the installation boxes should be as short as possible to prevent curling the wires and allow for easy assembling of the
in-wall part.
• Installation wires should be carried securely and not visible from the outside, preventing from the interference by unauthorized person.
• Recommended Ethernet cable for network connection is a twisted pair cable CAT-5e. The maximum cable length is 100 meters.
• Other inputs should be connected using the solid-core wires with cross-section from 0.14 to 0.34 mm2(26…22 AWG). Connectors are
also capable of connecting stranded wires.
• Close vicinity of mains (110V/230V) electrical wires may cause deterioration of the transmission through the Internet and potential
noise on the inputs.
www.domotica-shop.nl

10 INSTALLATION -MOUNTING THE INSTALLATION BOX
Mounting the installation box
Before installation pay attention to:
• Installation box must be mounted using the materials which will
not cause the tension that could deform the shape of a box after
the installation (e.g. by expanding).
• Mounting in the drywall requires using screws with hooks (not
included).
• Mounting in the insulation-lled wall (e.g. drywall with mineral
wool) requires to keep at least 10cm distance from the insulation
to prevent the device from overheating.
To install the box:
1) Prepare hole for 65mm x 75mm (diameter x depth) installation box.
2) Route cables to the back of the hole (see “Choosing and routing wires”on page 8).
3) Drag the cables through the rubber sealing on the back of the box, taking care to keep the tightness.
4) Mount the box in the hole and align it so the TOP arrow points up.
5) Make sure the box is ush with the wall and rmly attached.
It is recommended to use the plasterboard adhesive (type T) to securely install the box.
i
www.domotica-shop.nl

11
INSTALLATION -MOUNTING THE IN-WALL PART
Mounting the in-wall part
To install the in-wall part:
1) Use a screwdriver to unscrew the small screw that secures the
masking cap labelled with FIBARO logo.
2) Drag the wires through the hole located on the right of the in-
wall part.
3) Place the in-wall part of the device inside the installation box.
4) Using three attached screws fasten the part with the box, make
sure it is aligns properly and adjoins the wall.
www.domotica-shop.nl

12 INSTALLATION -CONNECTING WIRES
Connecting wires
To connect the wires:
1) Make sure that no wires are powered.
2) Remove the outer insulation to expose about 5 cm of the insulated inner wires, taking care not to damage them.
5
3) Separate and straighten the inner wires if twisted.
4) Cut the inner wires to 4 cm in length.
4cm
5) Remove the insulation from the inner wires to leave about 5 mm of exposed metal core on each wire.
4cm
5mm
6) Put the wires inside the terminals using long-nose pliers or tweezers according to diagrams below.
7) Make sure all wires are rmly attached.
Should you need to remove a wire from the connector we recommend to use a dedicated tool - WAGO 2059-189 (not included,
shown below) to minimize the risk of connectors damage.
i
www.domotica-shop.nl

13INSTALLATION -CONNECTING WIRES
Connecting ethernet/POE cable:
ETH1-ETH8 inputs are related to specied numbers of wires in RJ-45
connector according to the T-568B standard as shown below.
Connecting 12V DC power supply:
Inputs for connecting an external 12V DC power supply. Please
double-check correct polarity of power supply.
CAUTION
Before connecting the power supply, or attaching the wires to de-
vice terminals, make sure that the power supply and installation
complies with the limits of current and voltage.
Use only Class II or double insulated power supplies and periph-
eral devices which provide operating in SELV (Safety Extra Low
Voltage) circuits.
o O g B b G br BR
12V GND
!
www.domotica-shop.nl

14 INSTALLATION -CONNECTING WIRES
Connecting relays:
Congurable relay outputs 30V/1A. Outputs are not designed for
long-term supplying of external devices. Contacts are not connect-
ed to the ground and can be connected with any polarity.
R2 R2R1 R1
Connecting buttons for relays:
Congurable dry contact logic inputs designed to be operated by
reed sensors, switches, and relay outputs.
N1 GND N2
Connecting tamper switch to external system:
Anti-sabotage input, used for connecting to the external alarm
system. Normally opened contacts close after installing the
external, on-wall part of the device. Contacts are not con-
nected to the ground and can be connected with any polarity.
Parameters: max. 12VDC/50mA.
TMP TMP
To nd more information about potential use cases of each type of
connection see “Use cases“ on page 26.
www.domotica-shop.nl

15
INSTALLATION -MOUNTING THE ON-WALL PART
Mounting the on-wall part
To mount the on-wall part:
1) Install the masking cap and tighten it with a screw.
2) At this moment you can install a SD card (see “SD Card” on page
16 for more information).
3) Insert the on-wall part (metal at plate should be on the left) and
align it without using excessive force.
4) While holding the on-wall part, turn the inner black ring coun-
ter-clockwise using the included tightening tool until you feel
resistance.
5) Using the included hex key, tighten the small hex screw until it
ushes with the black ring (look at the picture on the right). Be
careful not to cause its deformation.
6) The device is ready to work. You can turn on the mains power and
move to device conguration guide.
www.domotica-shop.nl

16
SD Card
The device allows for installing the microSD Card for local storage of recordings.
FIBARO Intercom supports up to 128 GB microSDHC and microSDXC cards, Class 10 is recommended.
As for recording time, please refer to below chart.
Inserting a memory card:
1) Before inserting the microSD Card, please ensure the direction is
correct, otherwise the card and card slot may be damaged!
2) Open the plastic cover located behind the ring.
3) Use your nger to pull forward the latch that keeps the SD card
in place.
4) Lift the latch up.
5) Place the SD card into the slot with the label side facing up and
the gold contacts toward the slot.
6) Close the latch and pull it back until you feel a click.
7) Close the plastic cover.
INSTALLATION -SD CARD
128 GB
128 GB
Memory card capacity chart
Storage
Resolution 8 GB 16 GB 32 GB 64 GB 128 GB
1080p (1920 x 1080) 10h 19h 39h 77h 155h
720p (1280 x 720) 17h 35h 69h 139h 277h
576p (720 x 576) 25h 50h 99h 198h 395h
288p (352 x 288) 69h 139h 278h 555h 1110h
www.domotica-shop.nl

17CONFIGURATION -REQUIREMENTS
Conguration
Requirements
After proper installation of the FIBARO Intercom to run the device you need a:
• iOS mobile device connected to the Wi-Fi,
• FIBARO Intercom App,
• FIBARO ID account (which you can set up during the conguration process).
Make sure that during the conguration of FIBARO Intercom your smartphone is connected to the same network as your device.
During the setup stand close to the device.
Your network should be connected to the Internet at least for the conguration time.
Download FIBARO Intercom app from the App Store
https://www.baro.com/intercom/ios
i
i
i
www.domotica-shop.nl

18 CONFIGURATION -FIRST LOGIN
First login
Having a valid FIBARO ID account is necessary to use your device. Such account may be created through the same app that is
designed to operate the Intercom. Look below and follow one of the procedures.
Without existing FIBARO ID account:
1) Launch a downloaded FIBARO Intercom app.
2) Type in your e-mail address.
3) Set a password to be used for your FIBARO ID account.
4) Read the Terms of Service and Privacy Policy.
5) Verify your e-mail address by clicking a link provided in the message.
6) After creating an account, move to Creating home.
With existing FIBARO ID account:
1) Launch a downloaded FIBARO Intercom app.
2) Log in to your FIBARO ID account.
3) After successful login, you go directly to Creating home.
www.domotica-shop.nl

19
CONFIGURATION -CREATING HOME & CONFIGURATION OF THE FIRST DEVICE
Creating home
In this step, it is possible to create a new home or login to existing one.
Conguration takes place through BLE (Bluetooth Low Energy) protocol.
Make sure that Bluetooth is enabled on your smartphone.
Create new home:
1) Create a home and name it.
2) Tap Next to move to Conguration of the rst device in Home section.
If you log in to existing home, just select it from the list and proceed to the next step.
Conguration of the rst device
1) Stand close to the device.
2) Make sure that your smartphone is connected through Wi-Fi to the same network and Bluetooth connection is enabled.
3) After opening the app, you will see the list of devices waiting for conguration.
You can see the strength of BLE signal. If the signal is too weak, try to come closer to the device.
4) Choose the right device and name it if you want. Then, the next step is Connecting to the network.
i
i
www.domotica-shop.nl

20 CONFIGURATION -CONNECTING TO THE NETWORK
Connecting to the network
After selecting your Intercom from the list, you can establish a network connection.
You can do this in three ways: via Wi-Fi or LAN (automatically or manually).
Wi-Fi connection
Make sure that the range of Wi-Fi signal is good enough. If the Intercom is located far from Wi-Fi router,
it is strongly recommended to use Wi-Fi signal expanders nearby the Intercom.
1) Select Connecting via Wi-Fi.
2) Choose your Wi-Fi network from the list.
3) You can choose the network from the list or set it up manually.
The list shows Wi-Fi networks in Intercom range. It is not a list of networks found by your phone.
4) Provide a password to the network.
5) It is also possible to set up Wi-Fi connection manually. Provide credentials of your network.
Automatic LAN connection
After successful connection Wizard takes you straight to User Conguration.
Manual LAN connection
Provide necessary credentials: IP Address, Subnet mask, Gateway, and DNS. After that go to User Conguration.
After successful conguration of the device (resulting in streaming the live view from the Intercom) it is strongly recommended to
assign a xed IP address of the device in your router. It makes the device integration easier.
If the connection with the device is not successful, it may be necessary to reset your device to factory settings. Reset procedure is
described in “Resetting to factory settings“ on page 24.
i
i
i
i
www.domotica-shop.nl