Fiberstars WPC Series User manual

79-15169-00 Rev. A http://www.fiberstars.com Page 1 of 4
WPCRMR
WPC REMOTE RECEIVER
FOR WPC1 AND WPC2 INSTALLATIONS
The WPCRMR is shipped with a label indicating the Channel Code. Check the Channel Code with the Channel
Code on the Remote Control. If the Codes do not match, it will be necessary to change the transmission code on
the WPCRMR AND/OR the WPC transmitter.
TRANSMITTER DIP SWITCHES – Remove all screws from rear of remote. Separate the bottom cover from the
top cover. Ensure that the rubber gasket does not come off of the receiver. Locate the DIP switch as illustrate
d
b
elow. Change the DIP switches according to the illustration below. Reassemble the transmitter in reverse order
of disassembly. When tightening screws, ensure that they are all finger tight first. Then gradually tighten the
screws until they are snug. Over-tightening will damage the receiver enclosure and may allow moisture to seep
inside.
RECEIVER DIP SWITCHES – NOTE: IF CHANGING CHANNEL CODE ON RECEIVER, PERFORM
CHANNEL CHANGE BEFORE INSTALLING INTO THE WPC UNIT. Unscrew the four (4) screws
located on the back of the receiver to release the cover. NOTE: Take notice of how the wires enter and exit the
receiver. Remove the cover and look on the PCB to locate the DIP switch as illustrated. Change the DIP switches
according to the illustration below. Reassemble the receiver in reverse order of disassembly.
NOTE: The four DIP switches have an ON and an OFF position. Chan
g
in
gj
ust one DIP switch will chan
g
e
the code. MAKE SURE BOTH THE RECEIVER AND TRANSMITTER HAVE THE SAME DIP
SWITCH SETTINGS.
Receiver
screws
DIP switch
DIP Switch
Rear screws
15913
2 6 10 14
3 7 11 15
4 8 12 16
CHANNEL
DIP Switch
DIPSWITCH1234
Channel 1 OFF OFF OFF OFF
Channel 2 ON OFF OFF OFF
Channel 3 OFF ON OFF OFF
Channel 4 ON ON OFF OFF
Channel 5 OFF OFF ON OFF
Channel 6 ON OFF ON OFF
Channel 7 OFF ON ON OFF
Channel8ONONONOFF
Channel 9 OFF OFF OFF ON
Channel 10 ON OFF OFF ON
Channel 11 OFF ON OFF ON
Channel 12 ON ON OFF ON
Channel 13 OFF OFF ON ON
Channel 14 ON OFF ON ON
Channel 15 OFF ON ON ON
Channel 16 ON ON ON ON
Note: Sample shown is of Channel 9

79-15169-00 Rev. A http://www.fiberstars.com Page 2 of 4
Load Center
Cover Plate
Molex Connector
Mounting
Screws
Receiver Mounting
Holes
Switch Bracket
Face Plate
Molex Connector
Mounting
Screws
Receiver Mounting
Holes
INSTALLING WPCRMR INTO WPC1 AND WPC2
Receiver Removal: Unscrew the two Mounting screws for the Face Plate/Cover Plate. Disconnect the Molex
Connector. Carefully place Face Plate in a safe location. Unscrew the Receiver Mounting
Screws. Disconnect the four (4) “Quick Disconnects” from the Receiver. Note the different
sizes and types. Discard the old Receiver (unless otherwise directed).
Receiver Installation: Place receiver in the orientation as shown below. Tighten Receiver Mounting screws until
they are snug. Do not over-tighten as you may crack the base of the Receiver. Connect the
four (4) “Quick Disconnects”. There are two sizes and fit one way. Reconnect the Molex
Connector. The Molex Connector is keyed to fit one way. Do not try and force any
connectors as you may create a dangerous connection. Mount the Face Plate/Cover Plate
back into the WPC and tighten the mounting screws hand tight.
Test the WPC for proper function and operation.

79-15169-00 Rev. A http://www.fiberstars.com Page 3 of 4
WPCRMR
WPC REMOTE RECEIVER
F
O
R
W
P
C
3
I
NS
TALLATI
ONS
The WPCRMR is shipped with a label indicating the Channel Code. Check the Channel Code with the Channel
Code on the Remote Control. If the Codes do not match, it will be necessary to change the transmission code on
the WPCRMR AND/OR the WPC transmitter.
TRANSMITTER DIP SWITCHES – Remove all screws from rear of remote. Separate the bottom cover from the
top cover. Ensure that the rubber gasket does not come off of the receiver. Locate the DIP switch as illustrate
d
below. Change the DIP switches according to the illustration below. Reassemble the transmitter in reverse order
of disassembly. When tightening screws, ensure that they are all finger tight first. Then gradually tighten the
screws until they are snug. Over-tightening will damage the receiver enclosure and may allow moisture to seep
inside.
RECEIVER DIP SWITCHES – NOTE: IF CHANGING CHANNEL CODE ON RECEIVER, PERFORM
CHANNEL CHANGE BEFORE INSTALLING INTO THE WPC UNIT. Unscrew the four (4) screws
located on the back of the receiver to release the cover. NOTE: Take notice of how the wires enter and exit the
receiver. Remove the cover and look on the PCB to locate the DIP switch as illustrated. Change the DIP switches
according to the illustration below. Reassemble the receiver in reverse order of disassembly.
NOTE: The four DIP switches have an ON and an OFF position. Chan
g
in
gj
ust one DIP switch will chan
g
e
the code. MAKE SURE BOTH THE RECEIVER AND TRANSMITTER HAVE THE SAME DIP
SWITCH SETTINGS. The WPC3’s 4th position on the DIP switch of the Receiver selects Primar
y
or
Secondar
y
functions of the WPCRMR. The Transmitter onl
y
contains a 3
p
osition DIP switch.
Receiver
screws
DIP switch DIP Switch
Rear screws
DIPSWITCH123
Channel 1 OFF OFF OFF
Channel 2 ON OFF OFF
Channel 3 OFF ON OFF
Channel 4 ON ON OFF
Channel 5 OFF OFF ON
Channel 6 ON OFF ON
Channel 7 OFF ON ON
Channel8ONONON
Note: Sample shown is of Channel 8.
Transmitter DIP Switch
Fourth (4th) DIP switch
15913
2 6 10 14
3 7 11 15
4 8 12 16
CHANNEL
NOTE: ONLY CHANNELS 1
THROUGH 8 ARE AVAILABLE
FOR THE WPC-3.

79-15169-00 Rev. A http://www.fiberstars.com Page 4 of 4
Load Center
Cover Plate
Molex Connector
Mounting
Screws
Receiver Mounting
Screws
Switch Bracket
Bracket Spacer
Bracket Spacer
Terminal Block
Spacers
Two
Receivers
INSTALLING WPCRMR INTO WPC3
Receiver Removal: Unscrew the two Mounting screws for the Cover Plate. Disconnect the Molex Connector.
Carefully place Face Plate in a safe location. NOTE: The WPC3 uses two (2) receivers.
Unscrew the three (3) Receiver Mounting screws. NOTE: The Receiver Mounting
Screws holds both receivers with spacers in between the two receivers. Disconnect the
four (4) “Quick Disconnects” from the Receiver that is to be replaced. Note the different
sizes and types. Discard the old Receiver (unless otherwise directed).
Receiver Installation: Place receiver in the orientation as shown below. Insert the Receiver Mounting Screws on
the top two holes and the bottom right hole. Then place the Spacers onto the screws from
the back. Sandwich the spacers with the second Receiver. Carefully place onto the
enclosure in the proper orientation as shown. Tighten Receiver Mounting screws until they
are snug. Do not over-tighten as you may crack the base of the Receiver. Connect the four
(4) “Quick Disconnects” for the receiver that was replaced. There are two sizes and fit one
way. Reconnect the Molex Connector. The Molex Connector is keyed to fit one way. Do
not try and force any connectors as you may create a dangerous connection. Mount the
Cover Plate back into the WPC and tighten the mounting screws hand tight.
Test the WPC for proper function and operation.
FCC WARNING
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
2. Changes or modifications not expressly approved by Fiberstars Inc. could void the user's
authorit
y
to o
p
erate the e
q
ui
p
ment.