JAMO R-300 User manual

R-300
WARNING: Improper installation could result in damage to the re-
ceiver. Read all instructions before installation.

Introduction
The R-300 has its electronics housed in a brass cylinder. The front
end of the unit is a small round lens. This small receiver is designed
to be placed in very tiny spaces. One e ample is a small corner of an
equipment cabinet, or in the front baffle of the Jamo in-wall
speakers. A single ½-inch hole will accommodate the R-300. The
high sensitivity of this receiver gives you the ability to place the R-
300 further away from the hand held remote, increasing the
placement options you have.
CONNECTING THE RECEIVER
Use the supplied screw terminal block to e tend cables to the
connecting block
USING THE RECEIVER
To use the system, simply point the hand-held remote control trans-
mitter at the window on the R-300 receiver and press the proper
button. The R-300 does not change the way your remote control
works. The hand-held remote control transmitter for the stereo re-
ceiver will only operate the stereo receiver. Likewise, other trans-
mitters will only operate their companion devices.
The ma imum distance between the transmitter and the R-300 re-
ceiver will be different for each transmitter and when used directly
with the controlled device.
The system may be left on continuously, as it does not affect the
normal operation of the remote controlled device and consumes
very little power.

FEATURES
 E tremely small package, only 2in / 51mm deep.
 Works in normal 3-wire mode.
 Talkback green LED tests system for correct wiring as well as
indicating infrared reception.
 RF Grid included for EMI interference reduction.
The R-300 is available in two versions as follows:
R-300B Standard version, with mini 3 conductor 18 feet ribbon
cable and separate screw terminal block (supplied)
R-300W Same as the R-300B e cept with white bezel.
SPECIFICATIONS
 Infrared modulation frequency bandwidth: 30-100 kHz.
 Nominal reception range: > 30 feet / 9m
 Nominal reception angle: 55 degrees off a is
 Cable requirements for long lengths: (three-conductor)
24 AWG = 200ft / 60m
22 AWG = 600ft / 180m
20 AWG = 2000ft / 600m
18 AWG = 5000ft / 1500m
(unshielded OK)
 Ma imum cable length: 1 mile / 1.6 km with 18 gauge.
 Ma imum current output: 100 milliamps.
 Ma imum number of directly driven IR emitters: Up to four
connected in series. (Use Jamo Connecting Blocks for emitter
e pansion).
 Power requirements: 12 volts DC @ 10 mA.
Requires PS-1 power supply.
 Dimensions: ½in / 13mm diameter, 2in / 51cm deep.

69428 / 33.2000
The cope of the warranty
The warranty period will come into force as from the purchase date stated
on the invoice. The warranty will apply for the following period of time:
 2 years for electronics (power supply, amplifier, etc.)
 7 years for other parts (cabinet, speaker units, etc.)
In case of warranty inquiries, please contact your dealer.
In case of request for service under warranty, please enclose your original
receipt.
Defects covered by the warranty:
E cept for the defects stated below, the warranty covers any production
and material defects of the product.
Defects not covered by the warranty:
 Defects arising from accidents, misuse, normal wear and tear, mis-
maintenance, voltage variation, overloading, stroke of lightning, and
other force majeure events
 Defects arising from incorrect installation or operation
 Defects arising from modification/repair/attempt of repair by a non-
authorised service centre
 Defects arising from the use of non-original spare parts
 Defects on products with altered or lacking series number
 Other defects due to conditions or circumstances beyond the suppliers
control
Transportation costs for servicing are not covered by the warranty.
The supplier is liable only to repair or replace defective parts or products. A
replacement cannot e ceed the value of the product under warranty.