Fida WMO.L24 Mounting instructions

Maintenance and User Manual
DT00360_50EN
Rev. A del 17/07/2017
Pag. 1di 39
All rights reserved. No part of this publication may be reproduced, stored in any system, transmitted in any form or medium, mechanical, electronic, photocopying, recording or otherwise,
without the prior written consent of F.I.D.A. Srl.
No obvious responsibility is incurred in relation to the use of the information contained in this manual. Moreover, since F.I.D.A. Srl is constantly searching for the best quality for its products,
the information contained in this manual is subject to change without notice.
This manual has been drawn up with the utmost care; However F.I.D.A. Srl assumes no responsibility for any errors or omissions, nor assumes any responsibility for any damage resulting
from the information contained therein.
F.I.D.A. Srl via Volturno, 135 - 20861 Brugherio (MB) –ITAL IA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
WMO.L24 FULL HD
360C-M24O
WMO.L32 FULL HD
360M- M 32 O
WMO.L37s FULL HD
3 6 0 S- M 4 3 O
WMO.L42 FULL HD
360M- M 42 O
WMO.P42 FULL HD
360M- M 4 2 V
WMO.P55 FULL HD
360M- M 5 5 V
WMO.P65 FULL HD
360M- M 6 5 V
Description of Changes
Rev.
Date
Description
A
17/17/2017
First Emission

Maintenance and User Manual
Pag. 2di 39
DT00360_50EN
Rev. A del 17/07/2017
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
DECLARATION OF CONFORMITY
DECLARED UNDER OUR SOLE RESPONSIBILITY THAT THE PRODUCTS SPECIFIED BELOW:
P/N
Model/Type
Description
WMO.L24
360C-M24O
Monitor 24” landscape
WMO.L32
360M-M32O
Monitor 32” landscape
WMO.P37s
360S-M43O
Monitor 37” portrait stretched
WMO.L42
360M-M42O
Monitor 42” landscape
WMO.P42
360M-M42V
Monitor 42” portrait
WMO.P55
360M-M55V
Monitor 55” portrait
WMO.P65
360M-M65V
Monitor 65” portrait
COMPLY WITH THE REQUIREMENTS OF THE DIRECTIVES APPLIED, AND AS INDICATED BY THE REFERENCE
STANDARDS:
2014/35/EU
LOW VOLTAGE DIRECTIVE
2014/30/EU
ELECTROMAGNETIC COMPATIBILITY DIRECTIVE
2011/65/EU
ROHS: RESTRICTION OF HAZARDOUS SUBSTANCES DIRECTIVE
EN 50293
ELECTROMAGNETIC COMPATIBILITY (EMC) - ROAD TRAFFIC SIGNAL SYSTEMS.
ELECTROMAGNETIC COMPATIBILITY
EN 55014-1
ELECTROMAGNETIC COMPATIBILITY. REQUIREMENTS FOR HOUSEHOLD
APPLIANCES, ELECTRIC TOOLS AND SIMILAR APPARATUS. EMISSIONS
EN 55022
INFORMATION TECHNOLOGY EQUIPMENT - DISTURBANCE CHARACTERISTICS -
LIMITS AND METHODS OF MEASUREMENT
EN 55024
INFORMATION TECHNOLOGY EQUIPMENT - IMMUNITY CHARACTERISTICS - LIMITS
AND METHODS OF MEASUREMENT
EN 60529
DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE)
EN 61000-3-2
ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-2: LIMITS - LIMITS FOR
HARMONIC CURRENT EMISSIONS (EQUIPMENT INPUT CURRENT ≤ 16 A PER PHASE)
EN 61000-3-3
ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-3: LIMITS - LIMITATION OF
VOLTAGE FLUCTUATION, VOLTAGE FLUCTUATIONS AND FLICKER IN PUBLIC LOW-
VOLTAGE SUPPLY SYSTEMS FOR EQUIPMENT WITH RATED CURRENT <= 16 A PER
PHASE AND NOT SUBJECT TO CONDITIONAL CONNECTION.
EN 61000-4-2
ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-2: TESTING AND
MEASUREMENT TECHNIQUES - ELECTROSTATIC DISCHARGE IMMUNITY TEST
EN 61000-4-3
ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND
MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC
FIELD IMMUNITY TEST
EN 61000-4-4
ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND
MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY
TEST

Maintenance and User Manual
DT00360_50EN
Rev. A del 17/07/2017
Pag. 3di 39
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
Manufacturer
FIDA S.r.l.
Headquarter Milano - Via Volturno 135 - 20861 Brugherio (MB) –Italy
T. + 39 039 878733 - F. + 39 039 882003
[email protected] - PEC grup[email protected]
Warranty
Before contacting the manufacturer’s service centre, try to clarify the probable causes of the defect
with the help of the instruction manual. In the event of a call, communicate the model and serial number
of the product, date of purchase and a description of the problem.
Application of Warranty
The warranty applies to manufacturer products under this warranty. The manufacturer guarantees the
equipment against defects in workmanship and materials, subject to compliance with the instructions
contained in the instruction manual and that the product is used within the terms and conditions
established.
The warranty provides for the elimination of any damages or defects which occurred during the warranty
period and covered by the warranty. The material costs and timing of work are covered by the
manufacturer.
If during the course of the elimination of faults or defects covered by the warranty, if repairs or
replacements of parts not included in the warranty are made, the cost of repair or replacement parts are
charged to the customer on presentation of the relevant cost estimate.
Duration of Warranty
The warranty period begins from the date of purchase of the device and will expire after 24 months,
even if warranty claims have been made during that period of time. In this regard, it is essential to refer
to the sales invoice. All requests will be considered valid if made directly to the manufacturer during the
warranty period.
Effective date of warranty coverage
The claims under the warranty will be valid only if the device is accompanied by an invoice containing
all the necessary data, such as date of purchase, model and serial number. The warranty is
transferable, for example in the case of a private sale, only in the presence of the above-mentioned
documents proving the purchase.
Warranty Exclusions
The warranty shall not cover damage resulting from improper use, accident, modification, tampering or
improper maintenance, whether due to fraud, negligence, or incompetence including any damage
caused by incorrect voltages from power surges or power sources supply incorrect, damages and
breakages that occurred due to use of products under poor environmental conditions and contrary to the
instructions given in the manuals of operation and maintenance, damage caused by weather, accidental
falls, shocks, vandalism.
Excluded are the errors and damages caused by improper assembly or installation (if not performed by
the manufacturer), external events, such as damage in transit, damage caused by impact or shock,
repairs or modifications made by unauthorized third parties and with materials parts that are not original.
It does not include consumables (batteries, printer cartridges, etc ...) wear parts (mouse, print heads,
cartridges or magnetic media, etc ...) and damages arising from the use of parts subject to wear and
tear that does not satisfy the required technical characteristics, such as lamps or filters. In case the fault
proves out of warranty, the manufacturer will charge the costs of removal and troubleshooting according
to the rates in force, the possible replacement of parts under warranty will be implemented with the
simple signature of acceptance of replacement by the customer on the Report of Technical Assistance.

Maintenance and User Manual
Pag. 4di 39
DT00360_50EN
Rev. A del 17/07/2017
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
Information regarding this document
This manual uses the following symbols to indicate and classify precautions. Always follow the instructions
provided. Failure to observe these precautions may cause personal injury or property damage.
ATTENTION
Transactions which, if not performed as prescribed, can cause damage or
malfunction of the product.
ELECTRIC SHOCK
HAZARD
Indicates an imminently hazardous situation which, if not avoided, will result in
serious injury or death.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
serious injury or death.
PROHIBITION
Prohibition to take any action that if executed cause the occurrence of hazards and
/ or damage or malfunctioning of the equipment.
Recipients of the manual
FIDA products are for use according to proper procedures, described below, by a qualified operator and only
for the purposes described in this manual. This manual is intended for the following recipients:
Symbol

Manager of the product
Person entitled to maintenance and routine cleaning.

Technician or Installer
Specialized operator able to do the following activities :
❖Data and electronic installation and connection of Digital Signage
system.
❖Extraordinary maintenance.

Software Technician
Specialized operator able to do the following activities :
❖Maintain software system.
Related Manuals
The following user’s manuals are provided with product:
DT00355_06
DVP Board general specification
IO00360_39
Monito installation kit instructions 00360_K01
IO00355_01
Quick Start Guide

Maintenance and User Manual
DT00360_50EN
Rev. A del 17/07/2017
Pag. 5di 39
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
Summary
1. G EN E R AL I N F O RM A T I ON 6
1 . 1 L I M I T AT I O N S O F U SE 6
1 . 1 . 1 D E S T I N A T I O N O F U S E 6
1 . 1 . 2 E N V I R O N M E N T L I M I T S 6
1 . 1 . 3 P O W E R S U P P L Y L I M I T A T I O N : 6
1 . 2 I D E N T I F I C AT I O N P L A T E D A T A 7
1 . 2 . 1 L A B E L I N G 7
1 . 2 . 2 E L E C T R I C A L P A R A M E T E R 7
1 . 2 . 3 E L E C T R I C A L P R O T E C T I O N C L A S S 7
1 . 2 . 4 I P P R O T E C T I O N 7
1 . 2 . 5 D I M E N S I O N A N D W E I G H T 8
1 . 3 P A R T S I D E N T I F I C A T I O N 9
1 . 3 . 1 S T R U C T U R E 10
1 . 3 . 2 H A R D W A R E C O N F I G U R A T I ON 11
2. P A CK I N G , S H I P P IN G A N D H A ND L I N G 20
3. INS T A L L AT ION 21
3 . 1 A C C E S S T O I N T E R N A L P A R T S

21
3 . 2 P O S I T IO N I N G O F T H E E Q U I P M E N T I N T H E I N S T A L L A T I O N P O I N T

22
3 . 2 . 1 C HO I C E O F A N C H O R W A L L B R A C KE T 22
3 . 2 . 2 T Y P I C A L P O S I T I O N I N G 22
3 . 3 E L E C T R IC A L C O N N E C T I O N 26
4. M A IN T E NA N C E 27
4 . 1 P R E V E N TI V E M A I N T E N A N C E

27
4 . 1 . 1 I N S P E C T I O N A N D C L E A N I N G 27
4 . 2 C O R R E C T I VE M A I N T E N A N C E

28
4 . 2 . 1 R E P L A C E M E N T D A M A G E P A R T S 28
5. SPARE P A RTS 29
5 . 1 2 4” L A N D SCA P E GEN E R A L A S S E M B L Y 29
5 . 2 3 2” L A N D SCA P E G E N E R A L A S S E M B L Y 30
5 . 3 3 7”S L A NDSC A P E G E N E R A L A S S E M B L Y 31
5 . 4 4 2” L A N D SCA P E GEN E R A L A S S E M B L Y 32
5 . 5 4 2” P O R T R A IT G E N ER A L A S S E M B L Y 33
5 . 6 5 5” P O R T R A IT G E N E R A L A S S EM B L Y 34
5 . 7 5 5” P O R T R A IT M O N ITO R A S S E M B L Y . 35
5 . 8 6 5” P O R T R A IT G E N ER A L A S S E M B L Y 36
5 . 9 6 5” P O R T R A IT M O N ITO R A S S E M B L Y 37
5 . 1 0 E L E C T R IC A L P A R T S 38
6. ANN E X 39
6 . 1 D I A G N O S T IC B O A R D D V P 39

Maintenance and User Manual
Pag. 6di 39
DT00360_50EN
Rev. A del 17/07/2017
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1. General information
1.1 Limitations of use
1.1.1DESTINATION OF USE
Apparatus for professional use, designed to display public information sent by local data network.
The apparatus is not intended for consumers.
1.1.2ENVIRONMENT LIMITS
Do not install this product in the following places:
Locations subject to temperatures or humidity outside the range of values reported below:
❖Storage Conditions:
Temperature
Humidity
-20°C / 50°C
10% / 90%
❖Operating Conditions:
Temperature
Humidity
-30°C / 45°C
10% / 90%
Locations exposed to direct sunlight
Places where condensation can occur due to excessive temperature fluctuations.
Locations subject to corrosive or flammable environments or exposed to the risk of explosion.
Places exposed to oil or chemicals.
Apply security solutions appropriate and sufficient countermeasures when installing systems in the
following places:
Places where there is static electricity or other forms of noise.
Locations subject to strong electromagnetic fields.
Locations subject to possible exposure to radioactivity.
Locations close to power sources.
THE POINT OF INSTALLATION OF MONITOR MUST BE SUCH THAT ARE DIRECTLY IRRADIATED
BY THE SUN.
The direct radiation of the monitor can result in exceeding the maximum operating temperature limit.
1.1.3POWER SUPPLY LIMITATION:
The energy transport facilities must comply with the provisions of the regulations.
The grounding of the equipment has to be realized through equipotential lines with the ground
potential of the place of installation.
Ensure efficiency before installation of the circuit ground.
Upstream of the equipment has to be prepared, an easily accessible isolating device consists
of a thermal magnetic bipolar switch with an appropriate differential voltage, work current and
differential current of intervention I n: to coordinate the differential current of intervention I
n with the ground circuit.

Maintenance and User Manual
DT00360_50EN
Rev. A del 17/07/2017
Pag. 7di 39
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.2 Identification plate data
1.2.1 LABELING
The device is identified by a label attached on the outside of the product.
La The label contains the following data:
•Manufacturer
•Product code
•Product name
•Serial number
•Date of production
•Electrical parameter
It is forbidden to remove or replace the label. If the label had been damaged or lost, please inform FIDA.
1.2.2 ELECTRICAL PARAMETER
Product
Version code
Tension
Frequency
Power
Cos Φ
Current
WMO.L24
360C-M24O
230Vac
50/60 Hz
75W
0,98
0.33A - 0.75A*
WMO.L32
360M-M32O
230Vac
50/60 Hz
140W
0,98
0.62A - 1A*
WMO.L37s
360S-M43O
230Vac
50/60 Hz
92W
0,98
0.40A - 0.85A*
WMO.L42
360M-M42O
230Vac
50/60 Hz
146W
0,98
0.65A - 1.1A*
WMO.P42
360M-M42P
230Vac
50/60 Hz
146W
0,98
0.65A - 1.1A*
WMO.P55
360M-M55P
230Vac
50/60 Hz
161W
0,98
0.75A - 2A*
WMO.P65
360M-M65P
230Vac
50/60 Hz
266W
0,98
1.2A - 2.5A*
*Max current with heather
1.2.3 ELECTRICAL PROTECTION CLASS
CLASS
According to the type of protection against indirect contact the electric apparatus is classified
I
Component with a basic insulation provided with a device for connecting the masses to a
protection conductor.
1.2.4 IP PROTECTION
IP CODE
THE IP CODE, INTERNATIONAL PROTECTION MARKING, CLASSIFIES AND RATES THE
DEGREE OF PROTECTION PROVIDED AGAINST THE INTRUSION (INCLUDING BODY
PARTS SUCH AS HANDS AND FINGERS), DUST, ACCIDENTAL CONTACT, AND WATER
BY MECHANICAL CASINGS AND ELECTRICAL ENCLOSURES.
IP55
Dust protected and water protected by nozzle projected
NOTE
The value of IP Code must be provided with temperature and humidity degrees of Operating Conditions.

Maintenance and User Manual
Pag. 8di 39
DT00360_50EN
Rev. A del 17/07/2017
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.2.5 DIMENSION AND WEIGHT
MODEL
S
L
H
P
Weight
inch
cm
cm
cm
kg
360C-M24O
24
68
45
12,5
22
360M-M32O
32
85
55
12,5
30
360S-M43O
37
109,5
44
12,5
31
360M-M42O
42
109,5
69
12,5
38
360M-M42P
42
69
109,5
12,5
38
360M-M55P
55
84,5
137,5
12,5
70
360M-M65P
65
101,5
164,5
12,5
90

Maintenance and User Manual
DT00360_50EN
Rev. A del 17/07/2017
Pag. 9di 39
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.3 Parts identification
32”
42”
ID
Description
ID
Description
1
STRUCTURE
11
AIR INLET FAN WITH FILTER
2
AIR OUTLET FAN
12
LOCK
3
LCD PANEL
13
MAIN SWITCH
4
DOOR WITH GLASS
14
VOLTAGE PROTECTION
5
PLAYER
15
ANTINOISE FILTER
6
DIAGNOSTIC BOARD
16
CLAMPS
7
VIDEO BOARD
17
SOCKET 230V
8
MEDIA CONVERTER O ROUTER
18
RJ45 LAN PORT
9
POWER SUPPLY 12V
19
HEATHER
10
POWER SUPPLY 24V
20
FAN

Maintenance and User Manual
Pag. 10 di 39
DT00360_50EN
Rev. A del 17/07/2017
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.3.1 STRUCTURE
Box :
Milled aluminum extrusion with welding to ensure IP protection.
Epoxy powder coating Black Ral 9004 50% Gloss
Door :
Milled aluminum extrusion.
Epoxy powder coating Black Ral 9004 50% Gloss
Door Opening :
Rotation is on internal hinges, hidden from sight, mounted on the right equipment.
The closure of the door is realized with two key-controlled safety locks which are
positioned on the left side.
Frontal Protection :
Extra clear laminated glass with antireflective 4 + 3 mm. + 0.38 PVB, internal serigraphy
Black Ral 9004 between glasses, suitably glued to the door locking apparatus.
Anchors :
The structure is designed to accommodate a bracket with drilling std VESA or can be
anchored directly to the wall (see installation chapter).

Maintenance and User Manual
DT00360_50EN
Rev. A del 17/07/2017
Pag. 11 di 39
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.3.2 HARDWARE CONFIGURATION
1.3.2.1 Electric diagram 24”

Maintenance and User Manual
Pag. 12 di 39
DT00360_50EN
Rev. A del 17/07/2017
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.3.2.2 Electric diagram 32”

Maintenance and User Manual
DT00360_50EN
Rev. A del 17/07/2017
Pag. 13 di 39
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.3.2.3 Electric diagram 37s”

Maintenance and User Manual
Pag. 14 di 39
DT00360_50EN
Rev. A del 17/07/2017
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.3.2.4 Electric diagram 42”

Maintenance and User Manual
DT00360_50EN
Rev. A del 17/07/2017
Pag. 15 di 39
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.3.2.5 Electric diagram 55”

Maintenance and User Manual
Pag. 16 di 39
DT00360_50EN
Rev. A del 17/07/2017
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.3.2.6 Electric diagram 65”

Maintenance and User Manual
DT00360_50EN
Rev. A del 17/07/2017
Pag. 17 di 39
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.3.2.7 LCD Panel
Characteristic :
LCD 24”
LCD 32”
LCD 37”
LCD 42”
LCD 55”
LCD 65”
Active area :
23,8”
31,5”
37”
42”
55”
65”
Pixel :
1920 x 1080
1920 x 1080
1920 x 540
1920 x 1080
1920 x 1080
1920 x 1080
Aspect ratio :
16 : 9
16 : 9
32 : 9
16 : 9
16 : 9
16 : 9
Dynamics Contrast:
3000 : 1
3000 : 1
4000 : 1
4000 : 1
4000 : 1
4000 : 1
Colors :
16,7 M
8 bits
10/8 bits
10/8 bits
16,7 M
16,7 M
Brightness,:
1500 cd/m2
1000 cd/m2
1000 cd/m2
700 cd/m2
700 cd/m2
700 cd/m2
Response time :
14 ms
8 ms
6.5 ms
--
8 ms
8 ms
Viewing angle (H / V) :
178° / 178°
178° / 178°
178° / 178°
178° / 178°
178° / 178°
178° / 178°
LCD Power :
40W
77W
48W
81W
180W
230W
1.3.2.8 Modulo VCM
The card has the function of converting the video signal from an HDMI video output device to LVDS
signal.
The VCM board is equipped with a 230-pin MXM connector for the "carrier board" function for a
μQ7 module with a heat sink.
Video Out Features (LVDS)
Resolution: FULL HD 1920x1080
Interface: LVDS 2-channel 8bit
Video Features in (HDMI)
According to HDMI 1.4 specifications
Resolution: FULL HD 1920x1080
The processing video module can not perform the so-called video scaling, so the video input
resolution must match the video resolution of the LCD panel (normally 1920x1080), however some
resolutions may be displayed on the panel.
1.3.2.9 Modulo µQ7 (optional)
Processor :
Module µQ7 with processor i.MX6 (industrial class)
Chipset :
Dual Cortex A9 800Mhz
Memory :
4 Gb eMMC
RAM :
512 Mb
Video ouput :
2 channel LVDS 24 bit
Operating Temp. :
-40°C / + 85°C
1.3.2.10 Diagnostic Board 00355_DVP
The entire system is managed by a proprietary electronic card which controls every single function.
Power :
12Vdc
LAN :
2 Doors switch RJ45 - 100BASE-TX and 10BASE-T –Auto-negotiation
Thermoregulation :
Fan control and heater with NTC probe
Communication :
SNMP, HTTP

Maintenance and User Manual
Pag. 18 di 39
DT00360_50EN
Rev. A del 17/07/2017
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
Humidity :
Available
Automatic Brightness :
YES
Backlight :
YES
Sensors :
Tilt, Presence, external temperature available
LCD Sensor :
YES
1.3.2.11 Lux Sensor IR 310SC
Optional card to detect ambient light and turn on the receiving remote control signal
Ambient brightness:
YES
Remote controller:
available
1.3.2.12 Modulo riscaldatore anticondensa
The anti-condensation heating device consists of a heating element of about
100W/300W and a fan powered by the 12VDC activation relay and 230VAc output,
it is placed inside the apparatus in the central and low zone.
•Power Supply 230VAc
•Power: 100W
•Power: 300W (55” and 65” model)
•Type: PTC resistor, self regulating;
•Air flow: 11 m³/h
1.3.2.13 PC NUC (optional)
Processor :
Intel Core I3 / I5 –5^ generation
Memory :
Dual-Channel DDR3L SODIMMs
2/4 Gb RAM –32/64 Gb SSD
Graphics :
Intel HD graphics 6000
Mini HDMI 1.4a
Mini Display Port 1.2
Audio :
Up to 7.1 surround via Mini HDMI and Mini Display Port
Headphone/Microphone jack on the front Panel
Peripheral Int. :
4USB 3.0 external ports
2 USB 2.0 internal ports via 2x5 header
Infrared sensor
Storage:
Internal support SSD M.2 Key type M (22x42, 22x60 o 22x80)
Networking :
Intel 10/100/1000 Mbps Network connection
Intel wireless AC7265 M.2 antennaBluetooth e wireless pre-
assembled
Processor :
Intel Core I3 / I5 –5^ generation
To technical support, instruction manual and service information, please follow these links:
http://www.intel.it/content/www/it/it/nuc/one-pagers-nuc-specs-guide.html
https://downloadcenter.intel.com

Maintenance and User Manual
DT00360_50EN
Rev. A del 17/07/2017
Pag. 19 di 39
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
1.3.2.14 Touch Screen (optional)
Detection method
Projected Capacitive Technology
Input method
Finger and gloved finger
Number of
simultaneous touches
40
Sensor thickness
100 micron transparent polymer
Controller
Printed circuit board with mini USB
connector
Adhesive
Permanent, removable
Substrate
Float Glass, Gorilla Glass
Interface
HID
OS with multitouch
Windows 10, 8, 7*, Ubuntu 12.04,
Linux**, Android**, Chrome OS ***
OS with single touch
Mac OS X Yosemite (multitouch
support through TUIO bridge)
OS with mouse
emulation
Spinetix Media Player HMP 200,
Samsung SSP D Series
Data connectivity
USB 2.0
Touch accuracy
0,53% of sensor diagonal
Touch response
5 milliseconds
Finger separation
2,64% of sensor diagonal
Calibration
Available using control panel: no drift
Touch Sensor life time
expectancy
Unlimited
Touch Controller life
time expectancy
1 million hours
To technical support, instruction manual and service information, please follow these links:
http://displax.com/skin-fit/

Maintenance and User Manual
Pag. 20 di 39
DT00360_50EN
Rev. A del 17/07/2017
F.I.D.A. srl via Volturno, 135 - 2 0861 Br ugherio (MB) –ITALIA
Tel. [phone] (r.a.) - Fax [phone] - E-MAIL: info@fida.i t http :// ww w.fida.it
2. Packing, Shipping and Handling
The monitor has a specific packaging paperboard made with double-pitch and high-density polystyrene for the
proper transport, through the truck and / or train.
All electrical and electronic products should be disposed of separately from the municipal waste stream. Look
for collection facilities for disposal of obsolete equipment. As the European Directive 2002/96/EC
Dispose of the packaging material of the structure in accordance with applicable
regulations
The packaging films are made of polyethylene, PE.
Cardboard packaging is paper and should be disposed of in the special containers for
recycling paper.
The protectors are made of polystyrene (CFC-free) PS.