Field Controls FAN IN A CAN CAS4 User manual

www.eldcontrols.com
Please retain these instructions after installation.
This device MUST be installed by a qualied agency in accordance with the manufacturer's installation instructions. The denition of
a qualied agency is: any individual, rm, corporation or company which either in person or through a representative is engaged
in, and is responsible for, the installation and operation of HVAC appliances, who is experienced in such work, familiar with all the
precautions required, and has complied with all the requirements of the authority having jurisdiction.
READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION.
Installation Date:
Installed By: Phone:
COMBUSTION AIR SYSTEM
MODEL: CAS-4
This product is designed for use with any natural gas or LP burning furnace, water heater, or boiler with a 24
VAC control system. The CAS-4 may be used with one 24V-controlled combustion heating appliance and one
30mV standing-pilot gas water heater with the use of an additional CK-20 series control kit. Additional 120V or
24V-controlled appliances may also be served by the CAS-4 with the addition of one CAC-120 or CAC-24 control
kit per each additional appliance (see note)*. The CAS unit mechanically draws air into a structure and disperses it
near the combustion air intake of an appliance. Refer to Diagrams A and B for guidance in setting up the CAS
system based on the size and length of the connecting ductwork and the input rating of the appliance.
ITEMS INCLUDED IN KIT:
1- Motorized Blower 1- 4" galvanized intake air Vent Hood
2- Mounting brackets to secure the CAS to a wall 2- Wire/conduit connectors
1- 4" x 6" Pipe Increaser Fitting 1- 6" Orice Ring
1- Instruction Sheet 1- High/Low Motor Speed Switch
P/N 46284600 Rev L 09/19
WARNING! CONNECTIONS TO MULTIPLE APPLIANCES MUST FOLLOW INSTALLATION INSTRUCTION
WARNING! CONNECTIONS TO MULTIPLE APPLIANCES MUST FOLLOW INSTALLATION INSTRUCTION
WIRING DIAGRAMS. FOR HELP CALL 1-800-742-8368.
WIRING DIAGRAMS. FOR HELP CALL 1-800-742-8368.
*NOTE: The model CAS-4 design has recently been changed. Please note that there are dierences in construction,
operation, and installation of this CAS as compared to legacy product. Also, note that for multiple-appliance
installations, each additional appliance will require either a CAC-24 or CAC-120 control kit be provided for that
appliance. Installations with one heating appliance and one 30mV gas water heater will require an additional CK-20
series control kit in addition to the CAS-4.

page 2 of 12
Diagrams A and B and Table 1 show the maximum equivalent length and size of duct pipe that should be used
when installing the CAS system. Using these charts will help ensure that the proper amount of air is drawn
into the structure as needed by the appliance. The dened regions shown correspond to the CAS's airow
characteristics when using 4" and 6" diameter sheet metal duct pipe and the included orice ring. Follow the
guidelines below to properly size and setup the CAS.
1. Determine the maximum input ring rate of the appliance, or the maximum total ring rate of multiple
appliances that will be used.
2. Position the motorized CAS unit according to the guidelines in the Installation section.
3. Determine where the intake air vent hood will be located based on the recommendations in the Installation
section.
4. The CAS is equipped with a High/Low motor speed control switch. When calculating the maximum equivalent
feet, determine which speed is appropriate for the application. (Refer to Diagram A or B or Table 1)
5. Calculate the total equivalent length of duct pipe including elbows and ttings needed to connect the CAS
unit to the vent hood. (Refer to Diagram A or B or Table 1)
6. On Diagram A or B, locate the point that corresponds to the ring rate along the horizontal axis and the
equivalent length of the duct pipe along the vertical axis, if using for make up air.
7. The point should fall within one of the three regions on the table. Each region corresponds to a duct pipe
diameter of 4", 4" using the orice ring, and 6" respectively.
GENERAL SYSTEM OPERATION
1. The thermostat (wall thermostat, or aquastat) calls for heat and energizes a relay which activates the CAS
unit. After the CAS fan has come up to speed and air ow into the CAS inlet is estabished, an internal
air pressure switch closes and completes the circuit to allow the burner to re. If the appliance is power
vented, the venter and CAS activate simultaneously. After the CAS and power venter have come up to
speed, a pressure switch in the power venter control also closes and allows the appliance to re.
2. After the heating requirement has been satised, the thermostat circuit will open and deactivate the
burner and CAS unit.
3. For power vented systems with a post purge device, the power venter and CAS operate for a period of
time after the burner has shut o to purge remaining ue gases from the vent system.
INSTALLATION SAFETY INSTRUCTIONS
CAUTION: This device must be installed by a qualied installer in accordance with the manufacturer’s
installation instructions.
1. This combustion air system must be installed by a qualied installer. “Qualied Installer” shall mean an
individual who has been properly trained or a licensed installer.
2. Plan the system layout before installation to avoid the possibility of accidental contact with concealed
wiring or plumbing inside walls.
3. Disconnect power supply before making wiring connections to prevent electrical shock and
equipment damage.
SIZING AND SETUP
P/N 46284600 Rev L 09/19

page 3 of 12
EXAMPLE: A gas red appliance ring at 100,000 BTU/hr. where the CAS unit needs to be placed 30
equivalent feet from the intake hood.
From Diagram A or B, the point at 100,000 BTU/hr. on the Gas Firing Rate scale and 30 equivalent feet
falls in the 4" Duct, Hood, and Orice Ring region. The point is approximately 2⁄3of the horizontal distance
between the left and right boundary of the region. The left boundary is the edge of the graph, the right
boundary is the diagonal line that says 4" Duct, Hood & Orice Ring. Therefore, place the Orice Ring into
the inlet of the CAS so that it sits on the ledge above the fan. It does not matter which way the Orice Ring is
turned as long as it is pushed down against the ledge completely. Use 4" diameter pipe to connect the vent
hood and the CAS unit.
TOTAL INPUT OF APPLIANCE
TOTAL INPUT OF APPLIANCE
MAXIMUM EQUIVALENT FEET OF INSTALLATION
MAXIMUM EQUIVALENT FEET OF INSTALLATION
CAS-4, 4mV Gas
(BTU/hr.)
4" Duct And Hood w/
Restrictor
4" Duct and 4"
Intake Air Hood
6" Duct and 6"
Intake Air Hood
HI LOW HI LOW HI LOW
50,000 300 300 300 300 300 300
75,000 300 300 300 300 300 300
100,000 300 300 300 300 300 300
125,000 300 220 300 220 300 300
150,000 174 108 232 118 300 300
175,000 99 48 152 63 300 300
200,000 52 14 102 32 300 300
225,000 20 NA 68 13 300 239
250,000 NA NA 45 NA 300 150
300,000 NA NA 16 NA 300 53
350,000 NA NA NA NA 193 8
400,000 NA NA NA NA 109 NA
450,000 NA NA NA NA 56 NA
Table 1
P/N 46284600 Rev L 09/19

page 4 of 12
LOW SPEED SIZING CHART
0
50
100
150
200
250
300
50 100 150 200 250 300 350 400
GAS INPUT FIRING RATE (1000 BTU/hr.)
MAX. EQUIVALENT DUCT LENGTH (ft.)
0.0 0.50 1.00 1.50 2.00 2.50
OIL INPUT FIRING RATE (gallons per hour)
(1 gallon oil/hr = 140,000 BTU/hr.)
6" Duct & Hood
4" Duct & Hood
4" Duct & Hood w/ Orifice
Diagram A
Diagram B
P/N 46284600 Rev L 09/19

page 5 of 12
PLACEMENT OF THE CAS UNIT
The motorized CAS unit should be located on a at
horizontal surface within the same space as the appliance
and within 3' of the combustion air intake as possible.
Two mounting brackets are provided for securing the unit
against a solid structure, such as a wall, column, or the side
of the appliance itself. Use the included screws to attach
the brackets to the CAS housing as shown in Figure 1.
Secure the brackets to a solid structure with appropriate
fasteners. It is not required to use the brackets as long as
the unit is located so that it may not be bumped, moved,
or tipped over.
INTAKE AIR HOOD LOCATION
The 4" galvanized vent hood should be located on an
outside wall maintaining minimum clearances to other intake
and exhaust vents in accordance with the National Fuel
Gas Code, ANSI Z223.1, manufacturer's recommendations
and/or local codes which are applicable. The hood should
be located at least 10' from a power vented exhaust outlet
and should be on the same wall. The intake air hood
should be a minimum of 1' above grade or snowlines
where applicable.
INSTALLATION OF INTAKE AIR HOOD
After determining the location of the vent hood, cut a 4 1⁄2"
round or square hole in the wall. Insert the vent hood and
secure with appropriate fasteners. Take precautions to avoid
inter f e r e n c e w i t h w irin g o r o t h e r plu m b i n g i n t h e wall to b e c u t .
INSTALLATION OF DUCT
INSTALLATION
Figure 1
Figure 2
P/N 46284600 Rev L 09/19
Refer to Diagram A or B to determine what size pipe is needed. Connect the duct pipe from the top of the CAS
unit to the Vent Hood in the wall. If using 4" diameter pipe attach the provided 4" x 6" Pipe lncreaser Fitting to
the top of the CAS unit. The duct should be supported with appropriate mounting straps from oor joists, walls,
or other solid structures. The straps should be placed so as to keep the ductwork out of passageways. (See Figure
2) A minimum of 12' of pipe should be run to help temper outside air being drawn in. All joints in the duct system
must be sealed by appropriate tape or other means meeting all applicable building and mechanical codes.

page 6 of 12
WIRING INSTRUCTIONS
Wire the CAS unit in accordance with the National Electric Code and applicable local codes. UNIT MUST BE
GROUNDED. Check the ground circuit to make certain that the unit has been properly grounded. The wiring
should be protected by an over-current circuit device rated at 15 amperes. CAUTION must be taken to ensure
that the wiring does not come in contact with any heat source. All line voltage and control circuits between the
CAS unit and the appliance MUST be wired in accordance with the National Electrical Code for Class I wiring
or equivalent.
Remove the wiring access cover to access the wiring terminals. Use the enclosed conduit connector(s) to route
the appropriate wires through the CAS housing. The incoming ground wire must be attached to the green
colored ground screw near the wire terminals. The following sections describe the most common applications.
The references to various series of control kits implies that any kit in that series may be used. If further information
or additional wiring diagrams are needed please consult Field Controls' technical support.
INTERNAL WIRING CONNECTIONS FOR THE CAS UNIT
Refer to Figure 4 for the internal wiring of the CAS-4 unit.
External Wiring Connections
Refer to Figures 5-12 for appropriate wiring method.
Figure 3
Figure 4- Chimney Vent Single 24V Furnace
WIRE KEY WIRE COLOR
MOTOR MANUFACTURER W1 W2 W3
McLean Engineering Black Blue Brown
All Others Brown Black Blue
P/N 46284600 Rev L 09/19
WARNING! CONNECTIONS TO MULTIPLE APPLIANCES MUST FOLLOW INSTALLATION INSTRUCTION
WARNING! CONNECTIONS TO MULTIPLE APPLIANCES MUST FOLLOW INSTALLATION INSTRUCTION
WIRING DIAGRAMS. FOR HELP CALL 1-800-742-8368.
WIRING DIAGRAMS. FOR HELP CALL 1-800-742-8368.

page 7 of 12
Figure 5- Power Vent Single 24V Furnace
Figure 6- Chimney Vent 24V Furnace and 30mV
Water Heater With CK-20FV or CK-20FG
P/N 46284600 Rev L 09/19

page 8 of 12
Figure 7 - Chimney Vent 24V Boiler Figure 8 - Power Vent Single 24V Boiler
P/N 46284600 Rev L 09/19

page 9 of 12
Figure 9 - Chimney Vent Two 24V Gas Appliances With CAC-24
P/N 46284600 Rev L 09/19

page 10 of 12
Figure 10- One Power Venter Two 24V Gas Appliances
P/N 46284600 Rev L 09/19

page 11 of 12
ITEM DESCRIPTION FIELD PART NUMBER
Motorized Fan 46274100
Pressure Switch Fxd for CAS-4TMR 511100200
24 VAC Relay for CAS-4 46161400
120 VAC Relay for CAS-3,4 46257300
MAINTENANCE
1. Inspect the system annually to ensure proper operation by observing that the fan activates when a call for
heat occurs and deactivates when the call for heat is satised.
2. Disconnect power to the CAS unit and repeat Step 1. Note: The unit should not run and the appliance
should not re in this condition.
3. Inspect the duct pipe for cracks and security to the CAS unit and vent hood. The CAS unit will not allow
the appliance(s) to re if inadequate air ow is allowed into the inlet of the CAS.
4. Clear any obstructions, if present, from the inlet of the vent hood and the outlet of the CAS unit.
5. Periodically, the fan blade chamber may need cleaning. First, disconnect the power supply to the CAS.
Next, disconnect the duct pipe from the unit. Then remove the top pan and clean the fan housing area as
needed. Reattach the top pan, reconnect the duct pipe and the power supply.
REPLACEMENT PARTS
The following items are available for replacement, if needed. In order to replace these parts, power must be
disconnected and the unit must be disassembled. If this is necessary, take note of the positions and locations
of whatever items that may need to be removed to replace other items.
If in doubt, please consult Field Controls Technical Support at 1-800-742-8368.
P/N 46284600 Rev L 09/19

Phone: [phone] • Fax: [phone]
www.fieldcontrols.com
© Field Controls, LLC P/N 46284600 Rev L 09/19
This manual may be downloaded and printed from the Field Controls website (www.eldcontrols.com)
This manual may be downloaded and printed from the Field Controls website (www.eldcontrols.com)
WARRANTY
WARRANTY
For warranty information about this or any Field Controls product, visit:
For warranty information about this or any Field Controls product, visit:
www.eldcontrols.com
www.eldcontrols.com
Field Controls Technical Support
Field Controls Technical Support
1.800.742.8368
1.800.742.8368
eldtec@eldcontrols.com
eldtec@eldcontrols.com