fifthplay 98-404 User manual

1. INTRODUCTION 2
2. PACKAGE CONTENTS 2
3. SPECIFICATIONS 3
4. CHOOSING A SUITABLE LOCATION FOR THE WINDOW/DOOR CONTACTS 4
5. ALARM SIGNALS AND VISUAL INDICATION 8
6. FEDERAL COMMUNICATIONS COMMISSION STATEMENT 9
7. LIMITED PRODUCT WARRANTY 9
8. FAQ 10
9. CONTACT 10
10. DISTRIBUTOR 10
SMART
WINDOW /DOOR CONTACT
USER MANUAL

SMART WINDOW /DOOR CONTACT USER MANUAL
2
1. INTRODUCTION
This smart window/door contact is a Z-Wave™ device (interoperable, with RF mesh-network technology which
works in two directions) and is compatible with every Z-Wave™ network and the related security framework. Each
device driven by Z-wave™ functions as a signal amplier, so that multiple devices ensure a greater number of transition
routes, which help to eliminate "RF dead spots". Z-Wave™ devices with the Z-Wave™ logo can also be used for this,
regardlessof themanufacturer.Furthermore,our devicescan alsobe used inZ-Wave™networks ofothermanufacturers.
2. PACKAGE CONTENTS
Window/ door
contact
1x 1x
Mounting kit
1x 1x
Battery
1x 1x
Quick start guide
1x 1x

SMART WINDOW /DOOR CONTACT USER MANUAL
3
3. SPECIFICATIONS
PRODUCT IDENTIFICATION
Fifthplay Product ID 98-404
DIMENSIONS
Main component
Length 88 mm
Height 21 mm
Width 25 mm
Sensor head
Length 37 mm
Height 20 mm
Width 12 mm
POWER CONSUMPTION
Battery power CR123A Lithium
RF COMMUNICATION
Protocol Z-Wave™
Frequency range 868.42 MHz
CONTROL PARAMETERS
Temperature 0 - +60℃
Relative humidity 10 – 95%
Action radius 30 m
ZWAVE COMMAND CLASSES
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_BATTERY
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_NOTIFICATION_V4 (Mapping COMMAND_CLASS_BASIC)
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SECURITY
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2

SMART WINDOW /DOOR CONTACT USER MANUAL
4
4. INSTALLATION AND ACTIVATION
4.1.1 INSTALLATION OF THE BATTERY
E
1. Loosen the screws on the rear side (E) of the window/door contact , place the battery and place the rear side
back onto the sensor.
2. The LED lamp of the window/door contact will slowly ash for 10 seconds; the sensor is ready for connection
to the gateway.

SMART WINDOW /DOOR CONTACT USER MANUAL
5
4.1.2 CONNECTING A WINDOW/DOOR CONTACT TO YOUR FIFTHPLAY CUBE
A
IMPORTANT: Ensure that the window/door contact is in the immediate vicinity (0.5 to 1 meter)
of the gateway.
You can connect your window/door contact to your fthplay cube in the following 2 ways:
Via the APP:
1. Open the fthplay Home app and log in.
2. At the top left of the app, click on and select 'CONFIGURATION'.
3. Go to 'DEVICES'.
4. At the top right, click on +.
5. Select 'SENSOR' as the type of device.
6. Select 'WINDOW/DOOR CONTACT'.
7. Wait until the gateway is in connection mode (Once the connection mode has been established, you will
see a notication on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no
devices to be added are found, the connection mode will automatically be terminated after 2 minutes.
8. Hold down the programming button (A) of the window/door contact for at least 1 second to connect it to the
gateway. Once the connection has been established, you will see a conrmation message on your screen.
9. Once the window/door contact has been added, you will see a notication on your screen.
10. If desired, change the name of the window/door contact.
Via the WEBSITE:
1. Go to home.fthplay.com and log in.
2. Go to 'CONFIGURATION'.
3. Go to 'DEVICES'.
4. Click on 'ADD A DEVICE'.
5. Click on 'ADD A SENSOR'.
6. Select 'WINDOW/DOOR CONTACT' and click on 'NEXT'.
7. Wait until the gateway is in connection mode (Once the connection mode has been established, you will
see a notication on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no
devices to be added are found, the connection mode will automatically be terminated after 2 minutes.
8. Hold down the programming button (A) of the window/door contact for at least 1 second to connect it to the
gateway. Once the connection has been established, you will see a conrmation message on your screen.
9. Once the window/door contact has been added, you will see a notication on your screen.
10. If desired, change the name of the window/door contact.

SMART WINDOW /DOOR CONTACT USER MANUAL
6
4.1.3 MOUNTING OF THE WINDOW/DOOR CONTACT
1. Mount the largest part of the window/door contact by using the screws or double-sided tape.
2. Place the smallest part of the window/door contact in the right position in between the arrows (B). If desired,
you can use the extra mounting bracket (D). Use the double-sided tape or screws to mount the whole unit.
3. The distance between the smallest and the largest part of the window/door sensor (C) may not exceed 1.9
cm.
D
B
C

SMART WINDOW /DOOR CONTACT USER MANUAL
7
4.1.4 DISCONNECTING A WINDOW/DOOR CONTACT FROM YOUR FIFTHPLAY CUBE
IMPORTANT: Ensure that the window/door contact is in the immediate vicinity (0.5 to 1 meter) of the
gateway.
You can disconnect your window/door contact from your fthplay cube in the following 2 ways:
Via the APP:
1. Open the fthplay Home app.
2. At the top left of the app, click on and select 'CONFIGURATION'.
3. Go to 'DEVICES'.
4. Select the window/door contact you want to remove.
5. Click on 'REMOVE'.
6. Wait until the gateway is in connection mode (Once the connection mode has been established, you will
see a notication on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no
devices to be removed are found, the connection mode will automatically be terminated after 2 minutes.
7. Hold down the programming button (A) of the window/door contact for at least 1 second to disconnect it
from the gateway.
8. Once the window/door contact has been removed, you will see a notication on your screen.
Via the WEBSITE:
1. Go to home.fthplay.com and log in.
2. Go to 'CONFIGURATION'.
3. Go to 'DEVICES'.
4. Select the window/door contact you want to remove.
5. Click on 'REMOVE DEVICE'.
6. Wait until the gateway is in connection mode (Once the connection mode has been established, you will
see a notication on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no
devices to be removed are found, the connection mode will automatically be terminated after 2 minutes.
7. Hold down the programming button (A) of the window/door contact for at least 1 second to disconnect it
from the gateway.
8. Once the window/door contact has been removed, you will see a notication on your screen.
A

SMART WINDOW /DOOR CONTACT USER MANUAL
8
5. ALARM SIGNALS AND VISUAL INDICATION
STATUS INDICATION ON THE
WINDOW/ DOOR CON
TACT
APP
NOTIFICATION REPORTING IN THE APP
ACTIVATION MODE
(the battery is being
installed in the window/
door contact)
- - ✓
OPENING CONTACT
the window/door contact is
being opened
LED ashes once Push notication / text
message / email ✓
IDLE MODE
(the window/door contact is
functioning properly)
- - ✓
LOW BATTERY VOLTAGE -Push notication / text
message / email ✓
DISMANTLING SECURITY
(the window/door contact is
installed incorrectly)
LED lights up
continuously
Push notication / text
message / email ✓

SMART WINDOW /DOOR CONTACT USER MANUAL
9
6. FEDERAL COMMUNICATIONS COMMISSION STATEMENT
This product complies with all of the relevant European guidelines and regulations. If applicable,
you can nd the EC declaration of conformity regarding this product at http://cube.fthplay.
com/downloads.
This product cannot be deposited in the unsorted waste. Take your discarded product to a
recycling centre or a recognised collection point. Just like producers and importers, you too
play an important role in the promotion of sorting, recycling and reuse of waste electrical and
electronic equipment. To nance the rubbish collection and waste treatment, the government
levies recycling charges in certain cases (included in the price of this product).
7. LIMITED PRODUCT WARRANTY
•The warranty period is two years from the date of delivery. The delivery date is the invoice date of purchase
of the product by the consumer. If there is no invoice, the date of production applies.
•The consumer is obliged to inform fthplay in writing about the non-conformity, within two months of
noticing the defect.
•In case of a non-conformity, the consumer only has the right to a product repair or replacement free of
charge, which shall be decided by fthplay.
•fthplay shall not be held liable for a defect or damage resulting from incorrect installation, improper or
careless use, incorrect operation, transformation of the product, maintenance that does not adhere to the
maintenance instructions or an external cause, such as damage due to moisture or overvoltage.
•The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where fthplay sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.

SMART WINDOW /DOOR CONTACT USER MANUAL
10
8. FAQ
Consult our frequently asked questions page on cube.fthplay.com/FAQ or
consult the user manuals on cube.fthplay.com/downloads
9. CONTACT
Email: hello@fthplay.com
Telephone: [phone]
10. DISTRIBUTOR
Fifthplay NV
Generaal Lemanstraat, 47
B-2018 Antwerp