FIOR & GENTZ NEURO VARIO 2 User manual

27.08.2022 1/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Joint Assembly NEURO VARIO 2 and NEURO VARIO-SWING
Joint Assembly NEURO VARIO 2 and NEURO VARIO-SWING
Using NEURO VARIO-SWING as an Example
This online tutorial shows the joint assembly of our free moving system knee joints with plug + go
modularity:
NEURO VARIO 2
NEURO VARIO-SWING
You will find all important information on adjustment and conversion possibilities in the instructions for
use.

27.08.2022 2/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Joint Assembly NEURO VARIO 2 and NEURO VARIO-SWING

27.08.2022 3/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 1/15
Disassemble and clean the system joint. In order to clean the threads in the cover plate, use Super
Clean LOCTITE® 7063 to remove any insulating wax residues.
Note: mind the safety data sheet when using Super Clean LOCTITE® 7063.

27.08.2022 4/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 2/15
Apply spray adhesive to one side of the first sliding washer and adhere it to the cover plate. Grease the
other side of the sliding washer slightly with orthosis joint grease.

27.08.2022 5/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 3/15
Grease the axle bore of the joint axis and the friction surfaces of the bearing nut with orthosis joint
grease.

27.08.2022 6/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 4/15
Put the bearing nut into the intended opening of the joint’s upper part and make sure that it is in the
correct position. Secure the bearing nut with one finger.

27.08.2022 7/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 5/15
Grease the second sliding washer slightly with orthosis joint grease.

27.08.2022 8/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 6/15
While still securing the bearing nut, place the second sliding washer onto the joint’s upper part and
mount the joint’s lower part.

27.08.2022 9/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 7/15
Mount the cover plate. Screw in the first countersunk flat head screw (axle screw). Continue with the
second countersunk flat head screw while still securing the bearing nut.
Note: you will find information about the torque (Nm) on the system joint’s cover plate or in the
instructions for use.

27.08.2022 10/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 8/15
Make sure not to damage the sliding washer during assembly. Jammed sliding washer particles can
cause lateral play in the system joint.

27.08.2022 11/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 9/15
Check if the bearing nut is placed completely in the intended opening.
Note: the delivered screws always match the respective system joint. A potential discrepancy between
the length of the screws and the threads of the bearing nuts has no effect on the load capacity of the
system joint.

27.08.2022 12/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 10/15
Check if the system joint moves freely. Bring the system joint in extension. In order to check the flexion,
hold the orthosis in a horizontal position and then let go of the thigh shell. The thigh shell should
smoothly fall downward up to the maximum possible flexion angle.
If the system joint does not move freely, mount the next thinner sliding washers, repeat all steps from
step 6 onwards and check again.
Note: at a bilateral orthosis, only check one system joint at a time.

27.08.2022 13/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 11/15
Check if the system joint moves without lateral play. Hold the lower leg shell and try to move the thigh
shell in varus-valgus direction. If the system joint runs with lateral play, mount the next thicker sliding
washers, repeat all steps from step 6 onwards and check again.

27.08.2022 14/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 12/15
NEURO VARIO-SWING with Supporting Joint NEURO VARIO 2
At a bilateral orthosis, the main joint defines the maximum range of motion.
Loosen the alignment screw of the supporting joint until the extension stop finishes the motion at the
same time the maximum compression of the main joint’s spring unit is reached.

27.08.2022 15/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 13/15
Secure both screws with LOCTITE® 243 medium strength and the torque corresponding to the system
width. Let the adhesive harden (final strength after approx. 24 hours).
Note: mind the safety data sheet when using LOCTITE® 243 medium strength.

27.08.2022 16/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 14/15
Press the O-ring damper into the intended bore.

27.08.2022 17/17 NEURO VARIO 2 and NEURO VARIO-
SWING
Step 15/15
NEURO VARIO 2
Insert the stop damper and the alignment screw.
NEURO VARIO-SWING
Insert the spring unit and the screw unit.
Note: you can exchange the spring unit depending on the needed spring force.
NEURO VARIO 2 and NEURO VARIO-SWING
Adjust the extension stop until the nose of the joint’s lower part levels with the cover plate’s middle
mark. Thus, a physiological joint angle of 5° is reached.