aidapt Solo Bed Transfer Aid Manual

Fixing and Maintenance Instructions
Solo Bed Transfer Aid
N.B. This equipment must be installed by a competent installer/ technician.
Instructions for:
Solo Bed Transfer Aid and Solo Bed Transfer Aid Chrome 127Kg weight limit
Do not exceed the weight limit stated, doing so will put the user at risk.
1. Introduction
Thank you for deciding to purchase the Aidapt Solo Bed Transfer Aid.
The Bed Transfer Aid is manufactured from the nest material and
components available, when installed and used correctly it is designed
to give many years of reliable, trouble-free service.
The Solo Bed Transfer Aid can be tted to single, double, queen and
king size beds. It is available in two nishes, white epoxy and chrome.
2. Before Installation
2.1 Carefully remove all packaging. Avoid using any knives of
other sharp instruments as this may damage the surface of the Bed
Transfer Aid
2.2 Check the product for any visible damage. If you see any
damage or suspect a fault, do not use your product, but
contact your supplier for support.
3. Assembly and Installation
3.1 Your Bed Transfer Aid is shipped ready assembled with
its handle at its lowest setting.
3.2 To install, remove the mattress from the bed where
the Bed Transfer Aid is to be installed and check for any
obstructions.
3.3 Place the Bed Transfer Aid onto the base of the bed with
the large at base on the bed frame and the looped handle
facing upwards level with the side of the bed (See gure 2).
3.4 Move the Bed Transfer Aid up and down the bed to nd
the best position for the user to safely lift themselves.
3.5 Ensure that the frame of the Bed Transfer Aid is square
to the side of the bed and that both of the black feet at the
base of the unit are touching the side of the bed.
3.6 Replace the mattress ensuring that the Bed Transfer
Aid handle is pointing upwards and that the unit is in the
optimum position to suit the client’s needs.
Bed Frame
(Top down view)
Bed Transfer Aid
gure 2
gure 1

4. Height Adjustment
The height of the handle on the Bed Transfer Aid can be adjusted to suit the client’s requirements. To adjust
the handle simply remove the two grey e-clips from the base of the handle and lift the required height ensuring
that you do not exceed the last pre-punched hole on the base of the frame.
Once the desired height is achieved, re-insert the e-clips into the pre-punched holes, ensuring that both clips
pass completely through the tube frame and out the other side and are in place securely. Check that the unit
is properly adjusted by pulling the handle upwards, if there is no movement, then the height adjustment has
been carried out correctly.
5. Cleaning
The Bed Transfer Aid should be cleaned using a non-abrasive cleaner or mild detergent with a soft cloth only
Abrasive cleaners e.g. AJAX and/ or abrasive cleaning pads will seriously damage the product beyond repair
and should not be used. Always ensure that you wipe dry the equipment after cleaning.
6. Reissue
If you reissue or are about to reissue this product, please thoroughly check all components for their safety.
This includes;
Tightness of all nuts/ bolts/ castors and other screw in/ bolt in/ push in components. Also check all upholstery
for security, splits, exposed staples, etc.
If in any doubt, please do not issue or use, but immediately contact your supplier for service support.
7. Important Information
The Bed Transfer Aid hand grips have been designed to meet the latest MHRA guidelines on entrapment,
however you must ensure that there is no risk to the user or carer during the installation and service use of the
Bed Transfer Aid.
8. Further Information
We have attempted to cover most eventualities in this leaet, however if you have any specic queries, please
contact:
Aidapt Bathrooms Limited
Vulcan House, 5 Vulcan Way
New Addington
Croydon
CR0 9UG
Telephone: [phone]
Facsimile: [phone]
E-mail: [email protected]