FireBlitz FH700HIA Instruction Manual

Installation and
Maintenance
Version –16/8/2017
New Features
Firehawk Deaf Alert
New
Features !

Component Parts
FHB10W Smoke Alarm

New
Features !
DEAF ALERT CONTROL CENTRE
Multiple Control Centres Can
Now be Used +

New
Features !
Each smoke alarm will
double beep at the end of
learning.
Helpful beeps indicating
end of learning

New
Features !
This new version will operate with
previous versions …….
•Allowing easy in-service
extensions to the system
•The addition of new
products as they come on
line
•Individual Components can
be replaced with any
previous version if required.

New
Features !
Tamper –Proof Security Labels can
now be fitted instead of screws

Separate Control Centre
from Back-Plate
Remove Connection
Cover
Pass cables through Back
plate and into Control Unit
Fit Control Centre
onto Backplate or
Stand
Assembly and Testing

Plug in the power lead and the
power transformer into a
13amp socket and turn on
Switch on the radio base
or fit the header -
depending on version
Press the learn button
on the Control Centre
Take alarm to its working
location and press the
learn button
Watch for rapid green or red
LEDs on each unit (Three
Flashes per Second) ........
Plug in the
Vibrating Pad
Assembly and Testing
…….. until each alarm
double beeps and the
green LEDs flash every
minute
Do NOT connect
anything to
these two pins.

Assembly and Testing
•Test the smoke alarm - After a few seconds the pad, strobe and
red FIRE LED should operate.
•Then, after a few seconds, press the test button on the control
centre –The pad, strobe, 4 LEDs and smoke alarm should all
operate.

Final Installation
Refit the Connector Cover with
its screw or the Tamper-proof
Security Label
Re-assemble The control Centre
to its stand or backplate
1. Fix the Smoke Alarm to its final location
2. Locate Control Centre where the Strobe can be seen by the end user
3. Locate Vibrating Pad in suitable position to be able to wake a person –
for example under a pillow or touching their body in a chair

Power = Brief Red flash every minute followed by a
Single beep after 10 secs if the battery power is weak
Alarm = Repeating Red flashing light twice every second
+ a series of 3 beeps every 4 seconds
Fault = Double Bleep every minute
Test Button Jammed = Single beep every 11 seconds
Test = Repeating Red flashing light twice every second
+ a series of 3 beeps
Light and Sounds –
Smoke Alarm
Alarm Silence = Brief Red flash every 10 Seconds
Light and Sounds –
Deaf Alert
Power = Brief Green Flash every minute.
Alarm = Flashing Red light + Flashing Strobe light +Vibrating Pad
+ Alarm sound from the Smoke Alarm
Test = All four lights show one after another followed by
flashing from the Strobe, vibrations from the
Pad and alarm sound from the Fire Alarm
Fault = Yellow light every minute

Assembly and Testing
FireHawk Deaf Alert
(Quick reminder Notes)
1) Connect the Wires
2) Switch on Smoke Alarm Radio Base
3) Place Smoke Alarm in room of protection
4) Place Control Centre in Room of Alerting
5) Press the Learn buttons
Rapid green leds = Looking for each other and locking
Green leds every minute = ready to test.
Once the alarms double beep and the LEDs on Alarm and Control
centre revert to one GREEN flash every minute:-
6) Test system from both ends

General Notes
1. Up to 14 Control Centres, Heat or Smoke Alarms; in any combination,
can be connected to the system.
2. The system has a back-up battery so if it is necessary to move to
another room for a few hours , just un-plug from the wall socket and
take the complete system with you. Don’t forget to plug back into the
mains for charging
3. Always test the system at least once a week.
4. If you wish to add further alarms to an existing system, power down all
existing Alarms and Control Centres and re-learn with the additional
alarm(s) as shown from slide 5 above.
5. If you have any problems with this process – call our Helpline on …….
0800 008 6568