Fireside Lodge Barnwood Bunk Bed User manual

Parts needed:
1 - Headboard
1 - Footboard (end with built-in ladder)
2 - Safety rails (individually marked for holes)
1 - Bundle of 5 Slats
8 - 3” Torx Screws
4 - Rails (77” Long for Single & Double Beds & 82” Long for King & Queen Beds)
10 - 2” Wood Screws for slats
1 - Plywood for Upper Bunk
10 - 2” Wood Screws for Upper Bunk Plywood
16 - Bolts (2” length) & Nuts
1 - T-Support (King & Queen Beds Only) – (consists of qty 2 approx. 7”x75” boards – 1 has a slot)
Barnwood Bunk Bed Assembly Instructions
FIRESIDE LODGE
FURNITURE COMPANY
[phone]
www.residelodgefurniture.com
Tools Needed for Assembly:
Cordless Drill with Phillips Head
Ratchet w/9/16” socket
9/16” Wrench
T-25 Bit
Barnwood Bunk Bed Assembly Instructions Page 1
IMPORTANT! Please read and follow the
Bunk Bed Safety instructions on the last page
of this instruction packet.
is product is designed to provide the safety
levels of this certication when the assembly
instructions are properly followed. Completing
assembly as instructed will make beds safer.
Pictured is a Double/
Single Ladder Left

READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING ASSEMBLY
(Note: Two people are required for assembly. Headboard/footboard should be supported at all times to prevent
falling.)
1. 1. Bolt the 2 lower side rails to the bracket on the headboard (non-ladder end) DO NOT Tighten at this time.
2. 2. Repeat on footboard. DO NOT Tighten at this time.
3. Install upper safety rails. Do not tighten screws completely.
Barnwood Bunk Bed Assembly Instructions Page 2

4. Safety Rail installation instructions
1. Side rails must be attached to the headboard & footboard of bed loosely (DO NOT TIGHTEN BOLTS)
using the bolts provided before beginning the safety rail attachment process.
2. ere are corresponding letters on the top of the bed posts that match to the appropriate safety rail.
IMPORTANT: Safety rail numbers must be matched to up to assure the bed is square and secure once
assembled.
3. Once you have matched the safety rails to the correct head and footboard locations, attach the safety rail
using the screws provided into the predrilled locations on top of the safety rail.
4. PLEASE MAKE SURE ALL SCREWS ARE INSTALLED INTO ALL LOCATIONS PROVIDED WHEN
ATTACHING SAFETY RAILS.
5. Tighten the remaining bolts on all side rails.
Barnwood Bunk Bed Assembly Instructions Page 3

6. If you have a King or Queen bed, at this time, lay the 2 T-support pieces on the oor under the bottom bunk.
is will ease later assembly in Step #9.
7. Install slats on the bottom portion (DO NOT OVERTIGHTEN – as slats will crack – recommend to pre-drill
holes). Important! For safety, the slats at the head and foot must be spaced so the gap to the headboard
and to the footboard is 3” or less. e remaining slats may be evenly spaced between the two end slats.
8. Install plywood bunk board on the upper portion of the bed and secure with (8) 2” wood screws provided –
screw the plywood down onto the bottom bunk rail in 4 places on each side. Important! For safety, the plywood
must be positioned so the gap to the headboard and to the footboard is 3” or less.
Barnwood Bunk Bed Assembly Instructions Page 4

9. If you have a King or Queen Size Bed, assemble the T-Support (consists of qty 2 approx. 7”x75” boards –
1 has a slot) – stand the other upright in the slot and screw together – approx height will be 8.25”.
Lay assembled T-Support on the oor in the center of the bed running from head to foot and centered
between the two side rails.
10. Enjoy your Barnwood Bunk Bed for many, many years!!
Barnwood Bunk Bed Assembly Instructions Page 5
031314

Size of Mattress and Foundation
is bed is designed to use a mattress:
 • Single: 74½”x38”
 • Double: 74½”x53”
 • Queen: 79½”x60”
Topmattressmustnotexceed10”,3/4”foundationboardsupplied.Note:eremustbeatleast5”frommattress
sleepingsurfacetotopedgeofguardrail.
Replacement Parts
Replacementparts,includingadditionalguardrails,maybeobtainedfromplaceofpurchase.
Safety Warnings
 1. Followtheinformationonthewarningsappearingontheupperbunkendstructureandonthecarton.
  Donotremovewarninglabelfrombed.
 2. Alwaysusetherecommendedsizemattressormattresssupport,orboth,tohelppreventthelikelihood
  ofentrapmentorfalls.
 3. Surfaceofmattressmustbeatleast5inchesbelowtheupperedgeofguardrails.
 4. Donotallowchildrenunder6yearsofagetousetheupperbunk.
 5. Periodicallycheckandensurethattheguardrail,ladder,andothercomponentsareintheirproperposition,
  freefromdamage,andthatallconnectorsaretight.
 6. Donotallowhorseplayonorunderthebedandalwaysprohibitjumpingonthebed.
 7. Alwaysustheladderforenteringandleavingtheupperbunk.
 8. Donotusesubstituteparts.Contactmanufacturerordealerforreplacementparts.
 9. Useofanightlightmayprovideaddedsafetyprecautionforachildusingtheupperbunk.
 10. Ifthebunkbedwillbeplacednexttoawall,theguardrailthatrunsthefulllengthofthebedshouldbe
  placedagainstthewalltoprevententrapmentbetweenthebedandthewall.
 11. Alwaysuseguardrailsonboththelongsidesoftheupperbunk.
 12. euseofwaterorsleepotationmattressesisprohibited.
 13. Keeptheseinstructionsforfuturereference.
 14. StrangulationHazard–Neverattachorhangitemstoanypartofthebunkbedthatarenotdesignedfor
  usewiththebed;forexample,butnotlimitedto,hooks,belts,andjumpropes.
Barnwood Bunk Bed Safety Instructions
FIRESIDE LODGE
FURNITURE COMPANY
[phone]
www.residelodgefurniture.com • Single/Single B10120/B10121
• Double/Single B10130/B10131
• Queen/Single B10140/B10141
• Double/Double B10142/B10143
• Queen/Queen B10148/B10149