Fisher & Paykel DishDrawer DD605 Series User manual

DishDrawer
Installation instructions
NZ AU GB IE
DD605 and DS605 models

Safety and warnings
Important safety precautions!
Installation of this DishDrawer® requires basic mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building and electricity regulations.
At the completion of the DishDrawer® installation, the Installer must perform Final Check List.
Remove all packaging materials supplied with the DishDrawer®.
This dishwasher is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibility of the plumber and
electrician to ensure that each installation complies with all Codes and Regulations.
The DishDrawer® MUST be installed to allow for future removal from the enclosure if service is
required.
The switched power outlet must be outside the DishDrawer® cavity so that it is accessible after
installation.
Care should be taken when the appliance is installed or removed to reduce the likelihood of
damage to the power supply cord.
If the DishDrawer® is to be relocated from one installation to another it must be kept upright to
avoid damage from water spillage.
Make sure only new hoses are used for connection (supplied with DishDrawer®). Old hoses
should not be reused.
Failure to install the DishDrawer correctly could invalidate any warranty or liability claims.
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
WARNING!
Electrical hazard
Before installing the DishDrawer® , remove the house fuse or open the circuit
breaker.
If permanently connecting the DishDrawer®, be sure the power is isolated
and the DishDrawer® unplugged.
This appliance must be grounded. In the event of a malfunction or
breakdown, grounding will reduce the risk of electric shock by providing
a path of least resistance for electric current. This appliance is equipped
with a cord having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet that is installed
and grounded in accordance with all local codes and ordinances. Improper
connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service representative if
you are in doubt as to whether the appliance is properly grounded.
Do not modify the power supply plug provided with the appliance - if it will
not fit the outlet, have a proper outlet installed by a qualified electrician. Do
not use an extension cord, adapter plug or multiple outlet box.
Failure to do so may result in electrical shock or death

1
Contents
DOUBLE MODELS
Product and cabinetry dimensions
2
Installation
Cavity preparation 4
Route the hoses and move into the cavity 5
Removing the tub and levelling the product 6
Securing the product and refitting the tub 7
Plumbing and drainage - OPTION 1 8
Plumbing and drainage - OPTION 1 (connection) 9
Plumbing and drainage - OPTION 2 10
Plumbing and drainage - OPTION 2 (connection) 11
Fitting the toekick 12
SINGLE MODELS
Product and cabinetry dimensions
14
Installation
Cavity preparation 16
Route the hoses and move into the cavity 17
Removing the tub and securing the product 18
Refitting the tub 19
Plumbing and drainage - OPTION 1 20
Plumbing and drainage - OPTION 1 (connection) 21
Plumbing and drainage - OPTION 2 22
Plumbing and drainage - OPTION 2 (connection) 23
Final checklist 24
Important!
SAVE THESE INSTRUCTIONS
The models shown in this User Guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
availability in your country, please go to our website www.fisherpaykel.com or
contact your local Fisher & Paykel dealer.

2Product dimensions
O
B
C
E
D
F
G
H
J
N
P
Product dimensions (mm)
Prenished
LCD
DD605
Prenished
Flat door
DD605
Integrated
DD605
Aoverall height* of product 819.5 - 879.5 819.5 - 879.5 819.5 - 879.5
Boverall width of product 595 595 595
Coverall depth of product (excl. curvature/handle) 570 570 570
Ddepth of drawer (open) (excl. curvature/handle) 520 520 520
Eheight* of chassis 809 809 809
Fheight range of levelling feet 60 60 60
Gdepth of chassis 552 552 552
Hdepth of drawer front panel (excl. curvature/handle) 18 18 18
Idepth of curvature or handle 30 ** n/a
Jdepth of kickstrip 50 - 65 50 - 65 67 - 127***
Kheight of upper drawer front 394 398 398 min
Lheight of lower drawer front 312.5 311.5 311.5 min
Mheight of kickstrip (adjustable) 70 - 120 70 - 120 70 - 120
Nheight of installation tab slots (on top of chassis) 22 2
Oheight of drawer fronts 719.5 717.5 717.5 min
Pheight* of top of upper drawer to top of chassis 7 2 n/a
* Chassis heights include tab slots *** Prenished 50-65 mm; Integrated 67 mm less the Kickstrip
Panel thickness (Minimum Panel thickness using the supplied
screws is 9 mm).
** Designer handle - 41 mm, Curved handle - 36 mm
I
Installation diagrams for illustration purposes only
K
L
M
A
N
G
C
I
DOUBLE MODELS

3
Cabinetry dimensions
A
B
C
D
Cabinetry dimensions (mm)
Prenished
LCD
DD605
Prenished
Flat door
DD605
Integrated
DD605
Ainside height of cavity 820 - 882.5 820 - 882.5 820 - 882.5
Binside width of cavity 600 600 600
Cinside depth of cavity (inside) 580 580 580
Dheight of adjacent cabinetry 720 720 720
Eheight of kickstrip 70 - 120 70 - 120 70 - 120
Minimum clearances (mm)
2.5 mm
2.5 mm
13 mm
E
Installation diagrams for illustration purposes only
DOUBLE MODELS

4
Note: Services can be located
either side of DishDrawer®.
Cavity preparation
Parts supplied
These marks indicate mounting tab screw locations
Preferred position. If adequate clearance, services hole can be higher to clear toe kick space.
If hole is higher, ensure drain hose(s) are routed straight into the waste connection.
Clamp (1)
Wire clip (2) Phillips
16 mm
screws (9)
Drain hose
support (1)
Moisture
protection
tape (1)
(to prevent moisture
damage)
Drain hose
joiner (1)
Install
tabs (2)
Prefinished toe kick (1)
White or Black
90o
10 mm
max. 450 mm
220-240 VAC
min. 9 A

Moisture
protection
tape must
be applied.
min. ø50 mm
DOUBLE MODELS
*
*
*
min. 200 mm
If the Drain hose(s) supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit
P/N 525798 which will extend the drain hose(s) by 3.6m. The kit is available from the nearest Fisher & Paykel
Authorized Service Agent or www.fisherpaykel.com. DO NOT extend beyond this limit.
Hexagonal sockets (2)
(Long & Short)

5
Route the hoses and move into the cavity
DOUBLE MODELS
2
1
1
1
2
3
3
optional
1b
2
optional
1a
Tie together to avoid kinking
If top two tabs are being
used, ensure they’re securely
fitted before sliding product
into cavity.
Ensure hoses and cord
are not kinked or twisted.
Loosen feet first, but
do not fully extend
until product is in cavity.

6Removing the tub and levelling the product
30 mm
x 4
1
2
3
4
5
5
123
4
5
3
DOUBLE MODELS
4
Ensure the tub is removed and
then rotated counter-clockwise
to prevent kinked hoses.
Ensure product is level. Using the most appropriate length
Hexagonal socket supplied, and a screwdriver, fully extend
levelling feet up to required distance.
Hexagonal socket

7
Securing the product and retting the tub
DOUBLE MODELS
A
1
2
4
5
4
3
CC
BB
A
5
6
optional
The mounting tabs
are in pairs, one on
each side of the
product. At least two
sets of tab pairs must
be used.
Aand Btab pairs
OR Band Ctab pairs
or all three pairs.
Ensure the sound
insulation is
repositioned
correctly.
Before refitting the tub,
ensure the hoses are not
twisted and the latches at
the rear of each drawer
runner are facing forward.
Ensure the tub clips on
both sides are reset.
Ensure the tub is
now rotated
clockwise back.

8
DishDrawer® and Standpipe Ø38 mm
Water Pressure Max Min
Water softener models 1 MPa (145 psi) 0.1 MPa (14.5 psi)
Other models 1 MPa (145 psi) 0.03 MPa (4.3 psi)
Drains will need to be separated to satisfy Kosher requirements. We suggest you confirm
acceptability with your local Rabbi in respect to Kosher installations.
Plumbing and drainage - OPTION 1
DOUBLE MODELS
750 - 882.5 mm
Waste
Waste
Valve
Water
supply
(COLD)
Waste disposal
(optional)
Do not connect to
DishDrawer®
min. R200 mm
Max. distance of
hoses and cord from
chassis edge
Left hand
side
Right hand
side
Drain hose 2011 mm 1794 mm
Inlet hose 1561 mm 1344 mm
Power cord 1776 mm 1559 mm
Left hand
side
Right hand
side