Fisher & Paykel DH9060 Series User manual

INSTALLATION GUIDE
NZ AU
FABRIC CARE SOLUTION
DRYER ON PLINTH INSTALLATION
DH9060*, FM2060S1 and FM2060SG1 models

2
COMPONENTS REQUIRED
TOOLS
Supplied
F Spanner (dryer)
F Spanner (plinth)
F Allen key
Not supplied
F Box cutter
F Phillips screwdriver
F Level
PARTS
Supplied
F 1x Cold water hose
F 1x Hot water hose
F 1x Blanking cap
F 7x Plugs
F 4x M10 bolts
F 2x Plinth bolt hole covers
F 2x Dryer front brackets
F 2x Dryer rear brackets
F 2x Dryer rear mounting screws
Supplied (not required*)
F 1x Communication cable
*Not required for single product installation.

3
ACCESSING YOUR PRODUCT SPECIFICATIONS
For full product, cabinetry and service specifications, refer
to the Planning Guide. To access the Planning Guide, scan
the QR code or visit fisherpaykel.com/specify. Search by
appliance type, product name or model code.
1042
665
624

4
PRIOR TO INSTALLATION
3. Ensure power will remain
accessible following install to
allow access for any future
product maintenance.
Service holes should be smooth
with grommets installed where
required.
Refer to the services section
of the Planning Guide for more
details.
2. Ensure floor is level and clear
and a finished return has been
created.
1. Ensure cabinetry and
servicing specifications have
been met and clearances have
been considered.
Refer to the Planning Guide for
details.
fisherpaykel.com/specify

5
UNPACK
3. Protect flooring before
positioning dryer as close to
the installation location as
possible, ensuring enough
working room is left available.
1. Cut the straps and the line
printed on the top of the dryer
carton. Lift to remove. Discard
braces and corner posts.
Remove any packaging and
accessories from the drum and
base packer.
Dispose of packaging
responsibly.
2. Cut the straps and tape to
open the plinth carton from
the top. Remove the EPS cap
before lifting the plinth out.
Set cardboard aside for later
use. Ensure accessories are
removed from the EPS cap
before discarding EPS and
rubber spacers responsibly.

6
REVERSE DOOR (OPTIONAL)
The dryer door has reversible hinge and latch fittings and can be switched to open to the
left or right, as needed.
1. Unscrew hinge, remove door
and place face down on a
protected surface.
Remove plugs (x 8) from inner
door flanges, then remove
screws.
3. On dryer, unscrew and
remove latch cover to access
latch.
2. Insert flat-head screwdriver
in access slot to pry off inner
door. Rotate door 180 degrees
and fit back in place.
Reattach screws, alternating
between sides of the door.
Replace plugs.

7
REVERSE DOOR (OPTIONAL)
4. Unscrew latch, and slide to
remove.
6. Refit door hinge and secure
with hinge screws.
5. Rotate latch and insert on
opposite side of dryer. Secure
with screw.
Refit and secure latch cover
with latch cover screws.

8
1. Push the front of the plinth
to open. Remove the divider
before closing the drawer.
LEVEL PLINTH
2. Place the plinth in its final
install location. Adjust the feet
using the supplied spanner until
the plinth is level front to back
and corner to corner.
3. Using the spanner provided,
tighten the lock nuts against
the base of the plinth to lock
the feet in position.
Recheck that the plinth is level,
front to back and side to side.
Once level, move the plinth to
an accessible location to allow
washer/dryer to be installed.

9
1. Remove the four pre-fitted
plinth brackets using a Phillips
screwdriver. Set screws aside
for later use.
2. Fit the two supplied front
dryer brackets using the screws
removed in step 1.
3. Lift the dryer onto the plinth
and slot the front feet securely
into the front plinth brackets.
Ensure dryer and plinth are
correctly aligned.
FIT DRYER TO PLINTH

10
FIT DRYER TO PLINTH
4. Remove the two screws from
the front of the dryer and refit
through the plinth
5. Fit the two supplied rear
brackets to the plinth using the
screws removed in step 1.
Set aside any remaining screws.
6. Using the two supplied long
screws, secure the dryer to the
plinth at the rear.