Fisher & Paykel AeroSense Mounting instructions

NZ AU SG HK IN ME
Installation instructions
and User guide
Front loading dryers

1
Introduction 2
Safety and warnings 3
Installation instructions
Installation options 5
Installation – AeroSense™ and AeroLogic™ dryers 6
Installation – AeroDry™ dryer 8
Specifications 8
Dryer wall mounting instructions 9
Before you dry
Capacity, Sorting and loading, Drying times 11
Cleaning the lint filter 12
AeroSense™ dryer
Using your dryer 13
Dryness levels 13
1 hour setting 14
Key lock 14
Temperature settings 15
Delay start 15
Wrinkle free 15
AeroLogic™ and AeroDry™ dryers
Using your dryer, Drying cycles 16
Drying times 17
Drying rack 17
Operating problems 18
Manufacturer’s Warranty 19
Customer Care 20
Contents
Important!
SAVE THESE INSTRUCTIONS
The models shown in this User Guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
availability in your country, please visit our local website listed on the back cover
or contact your local Fisher & Paykel dealer.
Caution, risk of fire – this is a safety symbol.
Failure to follow the warnings outlined in these user instructions can cause
a fire hazard.

2
Congratulations on purchasing a Fisher & Paykel dryer. Your new dryer will give you the
convenience of tumble drying and your clothes the advantage of not being subjected to the
harsh overdrying effects of the sun. Your clothes will feel softer, retain their shape better and will
require less ironing.
At Fisher & Paykel we aim to provide products that are simple to use, ergonomic and energy
efficient. Thousands of tonnes of washing and 75 years of laundry experience have been
programmed into your dryer to help give you the best possible performance.
We hope you enjoy your new dryer. We have certainly enjoyed designing it.
Cost to dry
Many people are reluctant to use a dryer because
they believe they are expensive to run. True enough,
sunshine is free, but we don’t always have sunshine
and the benefits to you and your clothes can make
machine drying worthwhile.
The following example of a 2.5 kg load is used to
demonstrate the cost of drying.
4 T-shirts
1 Sweat Shirt
5 Pair Underpants
5 Pairs Socks
1 Pair Trousers
2 Pair Shorts
3 Handkerchiefs
This load was spun at a high spin speed (1000 rpm) and dried in an AeroSense™ dryer on dryness
level 4 (Medium dry and Extra dry lights on). The load took 60 minutes to dry.
For example if power costs 20 cents/unit, the load will cost approximately 30 cents to dry
(1.48 units x 20c). Check with your local Electricity Supply Authority for your domestic tariff.
Before using your dryer

Ensure the correct installation has been used for the dryer type. Installation depends on how the
dryer is vented.

Read the Safety and Installation instructions carefully.

Remove and discard the plastic power cord pin cover (required for transit only).

Ensure the pieces of tape surrounding the drum opening are removed. The tape MUST be
removed before operating the dryer.
Introduction
AeroSense™ dryer

3
Safety and warnings
WARNING!
Fire Hazard
Only dry fabrics that have been washed with water.
Do not use heat to dry articles containing foam rubber or similarly
textured rubber-like materials. Dry on Airing.
Do not stop a tumble clothes dryer before the end of the drying cycle
unless all items are removed and spread out in order to dissipate the heat.
As a clothes dryer produces combustible lint, the user must ensure there
is no accumulation of lint around the dryer if it is not vented outdoors.
Take care to prevent the accumulation of lint around the exhaust opening
and surrounding area.
Failure to follow these instructions can result in death or personal injury.
Dryer use

The tumble dryer is intended only for drying textile material washed in water.

The dryer should not be used to dry unwashed items.

Undergarments that contain metal reinforcements should not be placed in the dryer. Damage
to the dryer can result if the metal reinforcements come loose during drying. If you wish to dry
these items use a drying rack.

Check and remove all objects from pockets, eg lighters and matches.

Never dry rubber articles, fibreglass, or any plastic items or film, eg plastic lined tablecloths and
baby bibs.

Clothes should go through the cool down/airing phase in the final part of the cycle. This
ensures items are left at a temperature where they will not be damaged. If for any reason the
dryer is stopped before the cycle has finished, dry clothes should be removed immediately and
not left in the dryer. Clothes should be spread out to cool and not left bunched up, eg in a
clothes basket.

This dryer has been designed for domestic use only, not for commercial applications, such as
massage/beauty clinics where there may be increased lint accumulation or flammable materials
in the atmosphere or load.

Lint must not be allowed to accumulate around the dryer.

This dryer is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless given supervision or
instruction concerning the use of the dryer by a person responsible for their safety.

Young children should be supervised to ensure they do not play with the dryer.
Important!
If you are using an extension cord or a portable electrical outlet device (eg multi-socket outlet
box), ensure that it is positioned so that it does not come into contact with water or moisture.

4Safety and warnings
Lint
Accumulated lint in the dryer can become a fire hazard, it also reduces the efficiency of the dryer
by causing longer drying times and increased power consumption.

Clean the lint filter before every load.

Ensure the area around the dryer is clear of lint.

At regular intervals have the interior of the dryer cleaned of any accumulated lint. This must be
done by a qualified person for electrical safety.

If you change the mounting of the dryer from upright to inverted or vice versa, the dryer must
be cleaned internally by a Fisher & Paykel Authorised Repairer.
Spontaneous combustion
Important!
To reduce the risk of fire in a tumble dryer the following should be observed:

Items that have previously been cleaned in, washed in, soaked in or spotted with flammable
liquids or solids, eg petrol/gasoline, kerosene, dry cleaning solvents, vegetable or cooking oil,
waxes or other flammable or explosive substances are a hazard and should not be placed in a
tumble dryer.

Highly flammable substances commonly used in domestic environments include acetone,
denatured alcohol, petrol/gasoline, kerosene, some brands of spot removers, turpentine,
waxes and wax removers. Items that may contain such substances should not be placed in
a tumble dryer.

Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as
a tumble dryer. The items become warm causing an oxidation reaction in the oil. This oxidation
creates heat. If the heat cannot escape the items can become hot enough to catch fire. Piling,
stacking or storing oil-affected items can prevent heat from escaping creating a fire hazard.

If it is unavoidable that fabrics that contain vegetable oil, cooking oil or have been contaminated
by hair care products, or any other flammable substances, be placed in a tumble dryer, they
should first be washed in hot water with extra detergent – this will reduce, but not eliminate the
fire hazard. The cool down cycle of the dryer should be used to reduce the temperature of these
items. They should not be removed from the tumble dryer or piled or stacked while hot.

The dryer is not to be used if industrial chemicals have been used for cleaning.

Fabric Softeners or similar products should not be used in a tumble dryer to eliminate the effects
of static electricity, unless this practice is specifically recommended by the manufacturer of the
fabric softener product.

Rubber backed articles, foam rubber (latex foam), clothes or pillows fitted with foam rubber
pads, fibreglass, shoes containing rubber, shower caps, babies waterproof napkin covers and
waterproof textiles should not be dried in the dryer.

Items containing rubber (also known as latex foam) or similarly textured rubber like materials
should not be dried on any heat setting. Foam rubber material can when heated produce fire by
spontaneous combustion.

5
Installation options
Fig. 1 Free standing
115 mm
Fig. 2 Plinth height
Fig. 3 Upright wall
mounting
Minimum
lid clearance
Min. clearance
for dryer = 860 mm
Fig. 4 Inverted wall mounting
Washer**
Compact = 435 mm
Medium = 475 mm
Large = 525 mm
Important!
The dryer must be installed in a suitable location.
Do not install the dryer behind a lockable door, sliding door, or
behind a door where the hinge is on the opposite side to that
of the dryer in such a way that the full opening of the door is
inhibited. Ensure the dryer door can always be opened fully.
There are several different ways you can install your dryer.
1. Free standing
The dryer stands on the floor and can easily be
moved into position.
2. Plinth*
AeroSense™ and AeroLogic™ models only
A plinth, with adjustable feet, allows the dryer to be:
– matched in height to your washer.
– installed under a bench.
Plinths can be purchased from your dealer.
115 mm Plinth Part No. 94832
60 mm Plinth Part No. 94852
3. Upright wall mounting*
All models
The wall mounting kit allows the dryer to be
installed at any desired height minimising the
amount of bending and stretching.
Wall Mounting Kit Part No. 502067
4. Inverted wall mounting*
All models
A wall mounting kit and inverted panel allows you
to install the dryer above the washer or tub.
Electronic Inverted Panel (NZ/AU) Part No. 427901
Electronic Inverted Panel (Asia/ME) Part No. 427885
Wall Mounting Kit Part No. 502067
Low Ceiling Wall Mounting Kit Part No. P6450
* Contact your dealer for assistance with plinths,
inversion kits and wall mounting kits. Note: some
additional parts/accessories are not available in
all countries.
** Washer sizes. Compact: 560 x 560 mm,
Medium: 600 x 600 mm, Large: 650 x 650 mm.

6
Correct installation is very important for all dryers to ensure maximum efficiency and safety.
Important!
Never run the dryer unless the airflow system is free from obstruction.
There must be adequate ventilation to avoid the backflow of gases into the room from
appliances burning fuels, including open fires, when operating the dryer.
Exhaust air must not be discharged into a flue which is used for exhausting fumes from
appliances burning gas or other fuels.
External venting
The dryer has been designed to be externally vented to provide the following advantages:

Ensures optimum efficiency by preventing recirculation of moist air.

Eliminates condensation on walls and ceilings.

Reduces the chance of lint being sucked into the dryer.

Prevents lint and other fine particles being blown into
the room.
All external venting systems should be:

Made from galvanised metal pipe or be sleeved with
a galvanised metal pipe where the vent system goes
through a wall or ceiling.

Exhausted outside and not into another confined space.

Fitted with a vent cap outside to stop rain water entering
the dryer exhaust system.

Angled to avoid condensation running back into the dryer.

Less than 2 m long. Special installation is required for ducting over 2 m. Contact a Fisher & Paykel
Authorised Repairer.
DO NOT use the internal vent deflector as an external weather cap as this will cause restriction of
the airflow and a loss in performance.
Installation – AeroSense™ and AeroLogic™ dryers
Fig. 5 External venting

7
Flush venting
The dryer is vented through a hole in the wall, using a
galvanised metal pipe or flexible hose. This is suitable for floor
and wall mounted dryers installed against an outside wall.
Kit Vent External 400 mm Hose Part No. 460754
Movable venting
The dryer is vented using a flexible hose through a hole in the
wall. This allows the dryer to be moved from the wall slightly.
Suitable for floor mounted dryers only.
Flexible Hose 2 m Part No. 503858
Window venting
A flexible hose is used to vent the dryer through a window.
Maximum hose length is 2 metres.
Flexible Hose 2 m Part No. 503858
Flexible Hose 0.4 m Part No. 460601
Venting duct
The dryer is vented using an extendible duct that allows venting
to a window or through an existing wall vent. The duct can be
used with a flexible hose. Specially suitable for inverted dryers.
Venting Duct Kit Part No. P6451
Flexible Hose 2 m Part No. 503858
Internal venting
A deflector is included with the dryer (Part No. 460822P).
If external venting is not at all possible the deflector must be
fitted. This screws on to the back of the dryer over the exhaust
outlet. The outlet of the vent deflector must be clear of any
obstructions to ensure normal and safe operation. The outlet
should be directed towards the middle of the dryer (as in Fig.9).
Note: all efforts should be made to vent the dryer externally, if
possible, to avoid moisture build up in the area around the dryer.
Note: not all parts may be available in all countries.
Fig. 9 Internal venting
Installation – AeroSense™ and AeroLogic™ dryers
Fig. 6 Flush venting
Fig. 7 Movable venting
Fig. 8 Venting duct

8
Dryer position
The AeroDry™ dryer is front venting, whereby
the air is taken in through the grill at the rear
of the dryer and vented out through the grill
in the door at the front.
The dryer should be positioned so that the air
intake at the rear is unrestricted. The minimum
clearance needed from the wall is 50 mm.
Included with this dryer are two plastic spacers.
Fitting these on the rear of the dryer will ensure
the dryer is correctly positioned away from the wall.

Use screws provided to fit the spacers (as shown in
the diagram).
Directional outlet grill
The outlet grill can be rotated to direct the exhaust
air. It should be adjusted so that it points towards an
external window or door.
Specifications
AeroSense™ and
AeroLogic™ dryers AeroDry™ dryer
Dimensions
Width 565 mm 565 mm
Depth 560 mm 440 mm
Height 795 mm 795 mm
Electrical NZ / AU / Asia / Middle East NZ / AU
Volts 230/240 230/240
Hz 50 50
Amps 8.0 8.0
Note: if the electrical supply cord is damaged it must be replaced by the manufacturer or a
Fisher & Paykel Authorised Repairer in order to avoid a hazard.
Installation – AeroDry™ dryer
Fig. 10 Spacers
Fig. 11 Directional outlet grill

9
Tools and parts required:
1 x drill and 3 mm bit
1 x Phillips screw driver
2 x wood screws (14 x 50 timbertite screws)
1 x screw driver
1 x helper to lift dryer onto bracket
Extra tools and parts for mounting onto a concrete wall:
1 x 6 mm bit
2 x expanding bolts (M6 x 50)
1 x adjustable spanner
Note: read these instructions in conjunction with venting instructions.
1
Determine the position of the dryer on the wall and mark the bracket position.

A minimum of 70 mm is needed between the top of the bracket and the ceiling for ease of
installation.

If mounting over a washer allow sufficient room to open the lid of the washer or use a lid
catch retainer – Part no. 479273.

If the dryer is vented through the mounting wall ensure the venting hole clears any studs.
2
Fit the bracket to the wall. Ensure the bracket is securely fastened at both ends into studs
capable of supporting at least 108 kg (3 times the weight of the fully loaded dryer). Fit a timber
slat (also capable of supporting at least 108 kg) between the studs to mount the bracket onto if
the stud position is too wide.
3
Fit the spacers using the screws provided. If a timber slat has been used with the wall mounting
bracket, pack spacers away from the wall by the same amount.
4
Ensure the wall mounting slots on rear panel are clear of the half-punched material before
attempting to mount the dryer onto the bracket. We recommend using a screwdriver to
puncture the slots completely.
5
Mount the dryer on the bracket. Tilt the dryer out from below, engage the bracket in the back
panel slots then lower the dryer and rest against the wall.
WARNING!
Weight Hazard
Use two or more people to move and install the dryer.
Failure to do so can result in back or other injury.
6
Fit inverted control panel over the existing panel if necessary (available for AeroSense™ model
only).
Dryer wall mounting instructions

10
Note: if you change mounting from upright to inverted or vice versa the dryer must be cleaned
internally by a Fisher & Paykel Authorised Repairer.
Dryer wall mounting instructions
Fig. 12 Wall mounting instructions
Ensure bracket is securely
fastened at both ends
into studs capable of
supporting at least 108 kg.
Fit timber slats if necessary
(refer to page 9).
Ceiling
70 mm
Bracket holes
For the average
person the
recommended
height for the
bracket is
2070 mm from
the floor
Fit inverted control panel over
the existing panel if necessary
(AeroSense™ model only)
Fit spacers
as shown
Floor
519 mm
0 100 mm
WALL VENT HOLE
20 mm 104 mm
66 mm
66 mm
Ensure the slots are clear of
the half-punched material
before attempting to mount
the dryer onto the wall.

11
Capacity
The maximum capacity of your dryer (when the load is dry) is as follows:
Model NZ/AU Asia/Middle East
AeroSense™ 5.0 kg 6.0 kg
AeroLogic™ 5.0 kg 6.0 kg
AeroDry™ 4.0 kg N/A
Note: capacity ratings vary due to the qualifying criteria of different markets.

Overloading the machine will affect the drying performance, and may damage items.
Sorting and loading
To get the most efficient use of your dryer we recommend you sort your loads.

Look for a care label on your clothes. This will tell you if they can be safely tumble dried.

Close zippers, hooks and eyes, etc to reduce snagging and tangling.
Drying times

Drying very small loads is inefficient. Try to dry medium to large loads.

Sort your clothes into loads that take a similar time to dry, eg heavier items (towels, T-shirts,
flannelette sheets) from light items (synthetics and polyester cotton sheets and shirts). This will
prevent some garments becoming overdried while others are still damp.

Spin clothes at the highest spin speed suitable for the load type. The more water you remove in
the wash, the less time it will need to dry (NEVER put dripping wet clothes in or on top of the
dryer as excessive water could cause an electrical hazard).
Lint

Dry lint givers and lint collectors separately.
Lint Givers Lint Collectors
Towels Synthetics
Chenille Corduroy
Nappies Polyester cottons
Socks
To reduce creasing

Shake clothes out and load individually to help clothes dry evenly.

Launder permanent press garments separately, eg business shirts.

Allow enough room for clothes to tumble freely when loading.

Hang garments as soon as the dryer cycle is completed to reduce the need for ironing.
Before you dry

12
AeroSense™ and AeroLogic™ dryers
It is important to clean the lint filter after every
load, as the lint produced in the drying process
can become a fire hazard if it is allowed to
accumulate in or around your dryer.
The lint filter is located in the door opening.
1
Remove the lint filter, open it out and wipe
clean with your hand.
2
Close the lint filter and place it back in the
opening.
AeroDry™ dryer
The lint filter is located on the door of the dryer
behind the directional outlet grill. Lint should be
removed from the filter after every load.
1
To remove the outlet grill grasp the hub in the
centre of the grill and pull. Wipe the filter clean
with your hand.
2
To replace the grill, locate the hub over the boss
in the centre of the door and push firmly.
Note: do not clean your lint filter by vacuuming
or wetting it, as this may block the fine pores
essential for maximum airflow.
Cleaning the lint filter
Fig. 13 Lint filter – AeroSense™ and
AeroLogic™ dryers
Fig. 14 Lint filter – AeroDry™ dryer

13
Your AeroSense™ dryer takes the guess work out of choosing drying times by sensing the dryness
of the load. When your dryer senses that the clothes have dried to the dryness level you have
selected, the dryer will automatically turn itself off.
Using your dryer
1
Clean the lint filter before every load.
2
Load the clothes into the dryer.
3
Press POWER.
4
Select the dryness level.
5
Select the temperature setting and other drying options.
6
Press START/PAUSE.
The dryer will beep 5 times at the end of the cycle.
Fig. 15 Control panel – AeroSense™ dryer
Dryness levels
The AeroSense™ dryer has 5 dryness
levels from Light Dry through to Extra
Dry. Choose the dryness level to suit
your load using the guide opposite.
If you find the load is not dry enough,
select the next dryness level up. The
higher the level, the longer the drying
time and the drier your clothes will be.
Two lights are sometimes used to show
the dryness level. For example the Light-
Medium Dry and Medium-Extra Dry
settings.
Airing / Cool down
When the dryer has sensed that the load is dry it will automatically go into a 10 minute airing or
cool down cycle. During airing the drum tumbles and cool air is blown through the clothes. This
reduces creasing if the clothes are left in the dryer.
Light to Medium Settings
Delicate fabrics, eg synthetics
Fabrics prone to shrinking, eg sweatshirts
Or if you want the clothes slightly damp for ironing
Medium to Extra Dry Settings
Heavier fabrics, eg towels
Durable fabrics, eg denim
AeroSense™ dryer

14
1 hour setting
The 1 hour setting is a manual cycle which dries continuously for
60 minutes. The manual cycle does not sense when your clothes
are dry.
You can use the 1 hour setting when using a drying rack to dry
shoes, hats and other items that are best dried without tumbling.
Note: it is important to check the clothes throughout the manual
cycle to avoid overdrying.
Key Lock
Setting Key Lock prevents the dryer from being accidentally
switched off, or the programme being altered when the dryer
is running.
1
Select drying cycle and press START/PAUSE.
2
Press KEY LOCK (the lock shaped button) and hold for 2 seconds.
3
The Key Lock light will flash and the dryer will give 2 quick beeps.
4
The Key Lock light will remain on and all other keys will now
be locked.
To remove the key lock repeat steps 2 and 3.
Pausing the dryer
Opening the door or pressing START/PAUSE will stop the dryer tumbling. To start again close the
door and press START/PAUSE.
In the event of a power failure, your dryer will NOT restart automatically when power resumes.
We recommend restarting the dryer as soon as the power comes back on.
Important!
If you wish to stop the dryer before the cycle is finished, you MUST remove the clothes
IMMEDIATELY and spread them out to cool. DO NOT leave the clothes in the dryer or bunched up
in a clothes basket.
Note: If the door is opened when the dryer is running, and left open for more than 8 minutes, or
the door is opened during Airing the dryer will automatically switch off.
Drum reversal
To minimise tangling and to ensure your clothes dry efficiently, the dryer reverses the tumbling
during the cycle.
AeroSense™ dryer

15
Temperature settings
This dryer has 3 temperature settings; Regular, Low
and Airing.

The Regular setting is for drying most fabrics.

The Low setting is for drying delicates and synthetics.
It outputs half the amount of heat compared to the
regular setting, so the temperatures are lower for
maximum care of the fabrics.

The Airing setting is a cycle designed to freshen up
garments. The airing setting operates only on the
1 hour manual cycle.
The Regular and Low settings will operate on both
the manual and the auto-sensing cycles.
Delay start
DELAY START will delay the start of the drying cycle
by 3, 6 or 9 hours.
1
Select drying cycle.
2
Press DELAY START once for a delay of 3 hours. Press
again for 6 hours, a third time for 9 hours and again
to return to normal.
Selecting DELAY START will cancel the ‘beeping’ at
the end of the cycle.
Note: the DELAY START will not operate when the
1 hour manual cycle is selected.
Important!
Do not leave non-colourfast materials to sit wet in
the dryer as the dye may run.
Wrinkle free
Use WRINKLE FREE to minimise the creasing that
occurs when the clothes are left to sit in the dryer.
At the end of the cycle the drum will rotate briefly
every 5 minutes while cool air is blown through the
clothes. WRINKLE FREE will continue for 12 hours or
until the dryer is turned off. The dryer will beep to
remind you that the cycle is finished.
WRINKLE FREE can be turned on or off at any time
during the cycle.
AeroSense™ dryer

16
Your AeroLogic™ or AeroDry™ dryer has been designed so you can select how long you want the
clothes to dry for. So you know exactly when your clothes will be ready.
Using your dryer
1
Clean the lint filter before every load.
2
Load the clothes into the dryer and close the door.
3
Turning the dial clockwise, select the desired cycle and drying time. Push the dial in to start your
chosen cycle.
4
Try to remove the clothes from the dryer as soon as the cycle is completed to help
prevent creasing.
Note: the AeroDry™ dryer will stop every 5–6 minutes during operation to allow clothes to
redistribute.
To pause/stop the dryer at anytime, pull the door open.
To restart, close the door and push the dial in.
In the event of a power failure, your dryer will not restart automatically when power resumes. We
recommend restarting the dryer as soon as the power comes back on.
Important!
If you wish to stop the dryer before the cycle is finished, you MUST remove the clothes IMMEDIATELY
and spread them out to cool. DO NOT leave the clothes in the dryer, or bunched up in a clothes basket.
Drying cycles
Your AeroLogic™ or AeroDry™ dryer has two drying cycles designed to take care of all your drying
needs.

The REGULAR cycle is for drying more durable fabric or garment types, eg cotton, denim.
Here the heater remains on until the airing phase of the cycle.

The DELICATE cycle is for drying delicates and synthetics.
Here the heater pulses on and off, so garments are dried at lower temperatures.
Fig. 16 Control panel – AeroLogic™ and AeroDry™ dryers
Note: turn the dial clockwise only.
AeroLogic™ and AeroDry™ dryers

17
AeroLogic™ and AeroDry™ dryers
Airing / Cool down
When the dryer has finished drying it will automatically go into a 12 minute airing or cool down
cycle. During airing the drum tumbles and cool air is blown through the clothes. This reduces
creasing if the clothes are left in the dryer.
This phase of the drying cycle can be used to air clothes.
Drying times
With your new dryer it may take a few trials before you can accurately predict the correct drying
time for each individual load.
As a guide we have included some examples of loads and drying times. These times are
approximate only, based on the garments being spun at the maximum spin speed suitable for
the wash load.
Load comparison Approximate drying times
7 towels 60 – 80 mins
10 shirts (cotton/polyester) 20 – 40 mins
4 t-shirts plus 5 towels 60 – 80 mins
9 small delicates 20 – 30 mins
Drying rack
AeroSense™ and AeroLogic™ dryers only
A drying rack is available to dry shoes, hats and other items that are best dried without tumbling.
How to use the drying rack
1
Place the locating pin at the end of the drying rack into the hole in the centre of the rear of the
dryer drum.
2
Adjust the rack so that it is flat.
3
For the AeroSense™ dryer we recommend using the 1 hour manual cycle, and the low
temperature setting (fully featured models).
For the AeroLogic™ dryer we recommend using the Delicate cycle.
Important!
Check the articles throughout the cycle to avoid overdrying.
Note: the drying rack (Part No. 427899) is an optional extra and not available in all countries.

18
If your dryer is not operating properly use the checklist below to find the possible solution.
Pressing POWER or setting the timer does not turn the machine on.
Is the electrical cord plugged in?
Is the power switched on at the wall?
Is the door securely closed?
Is the dial pushed in?
Could your household power supply be at fault? Try plugging in another electrical appliance.
Make sure the timer is not in the OFF position.
Clothes are still damp.
Try selecting a higher dryness level.
Very small loads in the AeroSense™ dryer may under-dry. Increase the load size.
Pressing START/PAUSE does not start the AeroSense™ dryer.
Try pressing START/PAUSE again.
Has the KEY LOCK been set?
Dryer is taking a long time to dry.
Is the lint filter clean?
Is the airflow system free from obstruction?
The AeroSense™ dryer keeps stopping and starting.
Has WRINKLE FREE been turned on?
The AeroSense™ dryer is beeping and the pattern of lights is unfamiliar.
Turn the dryer off at the wall. Wait 15 seconds and turn it back on. Press POWER and restart dryer.
If the problem persists contact your Dealer or a Fisher & Paykel Authorised Repairer (refer to
page 20).
Operating problems