Fisher & Paykel WH9060J User manual

INSTALLATION GUIDE/USER GUIDE
NZ AU SG ROW
FRONT LOADING
CLOTHES WASHER
WH8560F, WH8060F, WH8560P, WH8060P,
WH7560P, WH9060J, WH8560J, WH8060J
& WH7560J models

1
CONTENTS
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may not
be available in all markets and are subject
to change at any time. For current details
about model and specification availability
in your country, please go to our website
www.fisherpaykel.com or contact your local
Fisher & Paykel dealer.
Registration
Register your product with us so we can
provide you with the best service possible.
To register your product visit our website:
www.fisherpaykel.com
Introduction 3
Safety and warnings 4
Installation instructions 6
Before your first wash 12
Safety features 13
Control panel 14
Wash cycles 18
Detergent and fabric softener 21
Wash preparation 24
Getting started quickly 25
Wash cycle options 27
Customising a wash cycle 31
Caring for your washer 32
Before you call for service 35
Fault codes 37
Troubleshooting 38
Manufacturer’s warranty 44
Customer care 46

3
INTRODUCTION
Welcome
Thank you for buying a Fisher & Paykel clothes washer. We are proud of this washer and
trust it will serve you well for many years.
At Fisher & Paykel we aim to provide innovative products that are simple to use, ergonomic
and kind to the environment. Your washer has numerous wash cycles and options so you
can perform every wash task with ease and the knowledge your clothes are receiving the
best possible care.
Please take the time to read these instructions carefully before you begin using
your machine.
Following the advice in this user guide will ensure you get the performance you expect
from your machine and that you get the best possible wash results. Keep these instructions
for future reference.
We hope you enjoy your new washer. We have certainly enjoyed designing it for you.
Front loading washer models

4
SAFETY AND WARNINGS
!WARNING!
Electrical Shock Hazard
Failure to follow this advice may result in electrical shock or death.
• If you are using an extension cord or a portable electrical outlet
device (eg multi-socket outlet box), ensure that it is positioned so
that it does not come into contact with water or moisture.
IMPORTANT SAFETY INSTRUCTIONS
WARNING! When using your clothes washer, follow basic precautions,
including thefollowing:
General
zThis product has been designed for personal, family or household use. This product is
not designed for any commercial use. Any commercial use will terminate this products
manufacturer’s warranty.
zA damaged power cord must be replaced by a Fisher & Paykel trained and supported
service technician or similarly qualified person in order to avoid a hazard. Do not use
the appliance until it has been repaired to avoid a risk of electric shock.
zDo not operate this machine if it has been damaged during transport. Contact your
Fisher & Paykel dealer or Fisher & Paykel trained and supported service technician.
zThis clothes washer is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge,unless they are supervised or given instructions on how to use the
washerby someone responsible for their safety.
zKeep children away from the washer while it is in operation.
zSupervise children to ensure they do not play with the washer or climb inside thedrum.
zThe washer should only be used for washing and rinsing of textiles where this
isindicated on the care label.
zDo not add petrol, dry-cleaning solvents, or other flammable or explosive substances to
the wash water. These substances give off vapours that could ignite or explode.
zDo not wash articles that have been previously cleaned in, washed in, soaked in,
or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive
substances as they give off vapours that could ignite or explode.
zThe door will be locked from the start of the cycle until the cycle is complete for safety
reasons. It is possible to open the door during the cycle under certain conditions. Never
force the door open.
zDo not touch the door during a cycle as the door can become hot.
zWhen 90°C temperature is selected, the door glass will become hot. Do not touch the
glass part of the door. Keep children away from the washer.
zDo not touch or operate the machine with wet hands or with bare-feet.
zDo not open the detergent dispenser during the cycle as hot water may come outofit.
zEnsure the installation provides accessibility to the plug or incorporate a switch in the
fixed wiring in accordance with the wiring rules to allow disconnection of the appliance
from the supply after installation.
zRead and follow the detergent manufacturers’ instructions carefully. Instructions on
how to use the detergent will be clearly indicated on the pack. Remember to store your
detergents out of the reach of children.

5
SAFETY AND WARNINGS
zDo not overload your washing machine beyond its rated capacity.
MODEL MAX CAPACITY Note:
zCapacity refers to the maximum
dry weight of items the washer
can wash at any one time.
WH7560P, WH7560J 7.5Kg
WH8060F, WH8060P, WH8060J 8.0Kg
WH8560F, WH8560P, WH8560J 8.5Kg
WH9060J 9.0Kg
zDo not wash an electric blanket in your washer unless the care label specifically states
it is safe to do so.
zDo not wash curtains in this washer, as sunlight makes them brittle and they may
disintegrate during washing.
zThe only user-removable parts of the washer are the inlet hose(s), detergent dispenser
and the pump filter. No other parts are designed to be removed by anyone other than a
Fisher & Paykel trained and supported service technician.
Installation
zFor guidance on how to install your product, please refer to installation instructions
contained in this document.
Water supply requirements:
zInlet water pressure: Maximum 1MPa (145psi), Minimum 30kPa (4.5psi)
zInlet water flow rate: Minimum 6litres/minute
zNew hose sets provided with the washer should be used to connect the washer to the
water mains. Old hose sets should not be re-used.
zWe recommend the inlet hose(s) are changed every 5 years. WARNING: Failure to do so
may result in a flood and damage to property.
zThe hot water temperature should not exceed 65°C and the cold water temperature
not exceed35°C. Temperatures above these may cause the machine to fault or cause
damage to the machine.
zInstall the machine on a solid and level floor surface ensuring it has at least 20mm
clearance on each side. The washer must not be installed on any textured floor
coverings (eg carpet, rugs).
Disposal
zWhen disposing of the washer, it is recommended that the door is removed to
avoidchildren getting trapped inside, and that the electrical cable is cut off
close to thewasher.

6
Accessories
Please check you received the following accessories with your Fisher & Paykel washer. You
will find them inside the drum or attached to the packaging.
z2 x Inlet hose(s) (for models WH9060J, WH8560J, WH8060J and WH7560J only 1 x
Inlet hose supplied)
z1 x Drain hose guide
z1 x Installation instructions and user guide
z1 x Spanner
z1 x Installation leaflet (attached to the top of the washer)
z1 x Inlet valve cap (excluding WH9060J, WH8560J, WH8060J and WH7560J models)
Unpacking
To ensure the best performance from your new washer please follow the instructions below.
Removing the packaging
1 Remove the outer packaging (including the polystyrene packer and plastic wrapping).
All packaging must be removed prior to use. Ensure these materials are kept out of
reach of children.
Note: A small amount of water may be seen inside the packaging and inside the washer. This
is the result of factory testing and is normal.
2 Tilt the machine backwards and ‘walk’ it off the base one foot at a time. Not doing so
may cause damage to your floor and washer.
3 Remove all packaging and accessories from inside the drum.
Removing the transit bolts
The clothes washer is fitted with 4 transit bolts at the rear to avoid damage during
transportation.
The 4 transit bolts MUST be removed prior to operation of the machine. Failure to remove
these will result in damage to the machine and compromise your manufacturer’s warranty.
To remove the bolts:
1 Use a spanner or socket to unscrew and remove all four transit bolts at the back
of the washer A.
2 Pull the black rubber grommets to remove the bolt, grommet and white plastic spacers
from the machine. Keep the transit bolts in case they are required for future transit of the
machine. Never transport the machine without the transit bolts properly fixed in place.
3 Cover the bolt holes with the white plastic plugs which are attached to the machine and
located near each hole B. Push to clip into place.
Removing the transit safety bolts
INSTALLATION INSTRUCTIONS
A
B

7
Product dimensions
PRODUCT DIMENSIONS WH9060J
WH8560F
WH8560P
WH8560J
WH8060F
WH8060P
WH7560P
WH7560J
WH8060J
MM MM MM MM
A Overall height
of product
850 850 850 850
B Overall width
of product
600 600 600 600
C Overall depth of
product (incl. dial and
door whenclosed)
645 645 645 590
D Depth of door open 1065 1065 1065 1010
E Minimum door
clearance to
adjacent wall
330 330 330 330
F Standpipe height min.
800 – 1200
min.
800 – 1200
min.
800 – 1200
min.
800 – 1200
Note: The exact height of your washer is dependent on how far the feet are extended from
the base of the machine. The space where you install your washer needs to be at least
40mm wider and 20mm deeper than its dimensions.
zElectrical supply: 220 – 240V, 50Hz Sinusoidal, minimum 10A.
zInlet water static pressure: Max. 1MPa (150psi), Min. 30kPa (4.5psi).
zInlet water flow rate at tap: Min. 6litres/min.
TOP VIEWWallFRONT VIEW
A
B
E
D
C
INSTALLATION INSTRUCTIONS

8
Location
This machine must not be installed and operated on a plinth.
Levelling the machine
It is IMPORTANT to level the machine to ensure good spin performance, and to minimise
noise, vibrations and wear and tear on the washer.
1 Before positioning the machine in its final position, check that the machine is level,
front to back and side to side.
2 Manoeuvre the product into its final position (we suggest a
minimum clearance of 20mm each side).
3 Use a spirit level to check that the machine is correctly
level. If needed, pull the machine out. Loosen the lock nut
using the spanner provided and wind the feet up or down
to correctly level the machine.
4 Using the spanner provided, tighten the lock nuts against
the base of the machine to lock the feet in position.
Connecting to the water supply
Inlet hose(s)
1 Connect the straight end(s) of the inlet hose(s) to the
tap(s) and the elbow end(s) to the corresponding machine
inlet valve(s). If present, the hot valve is colour coded
orange. Tighten the inlet hose end(s) by hand until the
hose seal just makes contact with the tap sealing face
and then tighten a further half-turn. Make sure there
are no kinks in the hose(s).
2 Turn the tap(s) on and check for leaks. Check for leaks
again after 24hours.
Locking the feet
Inlet hose ends
Elbow
(machine)
end
Straight
(tap) end
INSTALLATION INSTRUCTIONS

9
If you have an uncontrolled water heating source (eg a wet back or solar heating system)
please contact a qualified plumber to have a Hot ‘N’ Safe Valve fitted . This will ensure the
hot water temperature remains within safe limits.
Water supply requirements:
zInlet water pressure: Maximum 1MPa (150psi), Minimum 30kPa (4.5psi)
zInlet water flow rate: Minimum 6litres/minute
Cold supply only:
If you only have a cold water supply, the inlet valve cap (blanking cap) which came with
your washer must be connected to the hot inlet valve (with the exception of WH9060J,
WH8560J, WH8060J and WH7560J models). The cap prevents water leaking out of the hot
valve. This appliance incorporates backflow protection complying with AS3500.1. No further
backflow protection is required for connection to the water supply.
Your washer has an internal heater to heat water. If your model of washer has cold water
connection only (WH9060J, WH8560J, WH8060J and WH7560J models), or if you do
not connect a hot water inlet hose, your washer will automatically recognise there is no
hot water supply and its internal heater will heat the cold water to the selected cycle
temperature.
INSTALLATION INSTRUCTIONS

10
Draining
Drain hose placement in a stand pipe or tub
1 To guide the drain hose over the tub or
standpipe the hose guide must be fitted to
the drain hose. The height of the standpipe
or tub should be between 800 – 1200mm.
2 Secure the hose guide so it cannot become
dislodged from the standpipe or tub.
zIf the drain hose is placed on the ground or
if the standpipe or tub is less than 800mm
high, the washing machine will continuously
drain while being filled (siphon).
zRegularly check that your standpipe or tub
is free from lint or other obstructions, which
may affect how your machine works or may
cause flooding.
Attaching drain hose to spigot
1 Guide drain hose through hose guide.
2 Secure hose guide to back wall of cupboard
using a screw. The height of the drain
hose should be between 500 – 800mm
from ground level.
3 Attach drain hose to spigot and secure using
a hose clamp ensuring the blanking insert is
cleared from spigot.
4 Check for leaks.
zThe drain hose should be checked from time
to time and replaced if any damage (egwear,
cuts, bulges, kinks, leaks, etc) is found. Do
not bend the drain hose sharply, as this may
cause it to split.
zIn multi-storey apartments or any upper floor,
the machine should be installed on a floor
equipped with a drain.
zDraining must comply with local by-laws.
Fitting the drain hose guide
(20mm)
maximum
Standpipe 800 – 1200mm
Pull hose
through
guide
Attaching drain hose to spigot
Height 500 – 800mm
from ground
INSTALLATION INSTRUCTIONS

11
Electrical connection
1 This appliance must be connected to a 220V – 240V, 50Hz, sinusoidal, minimum 10A
electricalsupply.
2 Uncoil the power cord, remove and discard the plastic pin cover and plug
into a wallsocket.
3 Connect the appliance to an earthed outlet protected by a fuse of suitable capacity.
zCheck the power cord for damage and make sure it is not squashed or twisted when
installing the washer.
zAlways remove the power cord from a socket by the plug, not by the cord.
SPARE PARTS* PART NO.
Hose inlet long (2m) 422680P
Hose inlet large bore 426123P
Drain hose extension (not suitable for attaching to a spigot) 425627P
*Available from your Fisher & Paykel dealer or a Fisher & Paykel trained and supported service technician.
Completing the installation
Installation test cycle
Do this before you wash any items in your washer. This is to check that your washer is
installed correctly and that it is functioning correctly prior to use.
1 Turn your washer on by pressing ‘Power’.
2 Select the ‘Quick’ or ‘Super Quick’ cycle. Ensure the drum is empty and the door closed.
3 Touch the button. The machine will start to fill.
zObserve the machine for any problems (eg leaking from the hose(s), excess noise
orvibrations).
zThe washer will beep and display any faults on the screen if there are any problems.
Refer to ‘Before you call for service’ at the back of this book.
4 Wait until you see water in the bottom of the drum.
5 Touch to stop the cycle, then press ‘Power’ to turn the machine off.
6 Press ‘Power’ again, select the ‘Spin’ cycle and touch .
zCheck the drain hose is firmly secured to the standpipe or tub, or spigot.
zObserve that the machine pumps out the water, and spins.
If there are any problems, you must address these before proceeding with normal use.
The washer will automatically turn off at the end of the cycle if there are no problems.
INSTALLATION INSTRUCTIONS

12
BEFORE YOUR FIRST WASH
Before you start, it is a good idea to go through the following checklist:
1 Have the packaging and transit bolts been removed?
2 Is the drain hose threaded through the ‘Ubend’ (with no more than 20mm extended)
and hooked into your standpipe or tub, or attached to a spigot?
3 Is the hot hose connected to the hot valve (colour-coded orange, if present)? Is the cold
hose connected to the cold valve (colour-coded white)? Have the taps been turned on?
4 Is the machine correctly levelled, feet are locked and cabinet corners clear of the
floor and walls?
5 Has the power cord been connected to an appropriate power supply and the
power turned on?
6 Have you performed the installation test cycle?
7 We recommend you complete your first cycle with a half-load amount of detergent
and without a load in order to remove any residues remaining in the machine from the
manufacturing process.

13
SAFETY FEATURES
Door lock
The door of your washer will lock once you touch until the machine beeps at the end of
the cycle, ensuring safety for you and your family while your machine is operating.
To unlock the door during the cycle
zYou can open the door to add or remove items during the wash simply by touching the
button. The door will remain locked if the temperature inside the washer is above
60°C and/or the water level is above the bottom of the door seal (a warning will be
displayed in these circumstances, refer to ‘Before you call for service’).
zSimply touch , the machine will pause and the door will automatically unlock if the
conditions inside the washer are safe. The button and time to go will flash on the
screen while the washer is paused. Open the door and remove or add garments. Close
the door and touch to resume the cycle.
Add a Garment (WH8560F, WH8060F, WH8560P, WH8060P and WH7560P models only)
The ‘Add a Garment’ function can be used to interrupt the cycle to add or remove a
garment at any time during the wash part of the cycle (as long as the wash temperature
selected is lower than 60°C). Water in the machine will be drained to a level where the door
can be opened, if necessary. Refer to ‘Wash cycle options’ for more information.
Opening the door during a power failure
If there is a power failure during a wash cycle your
washer will stop and the door will remain locked. You
can unlock the washer door to remove your clothes by
opening the pump filter cover at the bottom right of
your washer. Simply place a coin or key in the slot and
tilt it upwards to lever the cover open, then pull the
door release tab.
Do not attempt to do this if the water level in the
washer is above the level of the door.
When power is restored you will need to restart your
machine by simply pressing ‘Power’. The washer will
remember where in the cycle it was up to.
Your washer also has the following protective measures:
zFlood protection – turns off valves and turns pump on if a flood condition is detected.
zOut-of-balance protection – stops and redistributes the load if an unbalanced load
condition is sensed, and/or slows the spin speed to compensate.
zExcess suds protection – pauses to allow suds to break down before
continuing the cycle.
Door release tab
Manual door opening
mechanism

14
SmartTouch™ Control Dial
The SmartTouch™ Control Dial provides easy and efficient wash cycle selection. As you
rotate the dial, the icon of the wash cycle selected will be illuminated, along with the
default settings for that cycle on the right side of the control panel.
SmartTouch™ buttons
The smooth, easy clean buttons enable easy selection of options with lights clearly showing
the selections you are making.
Digital display screen
The digital display screen provides feedback on how long the wash cycle has to go. If
you have programmed a ‘Delay Start’, the time remaining until the cycle will start will
be displayed here, along with any messages to help you with the overall running of your
washer (eg user warnings).
Time to go
Your washer displays approximately how many minutes the cycle you are running has
remaining, so that you can tell at a glance when your washing will be finished.
Please be aware that a number of factors can influence the overall cycle time, eg the water
flow rate, water pressure, whether hot water is being used from the tap or the water is
heated by the internal heater, load size, cycle and option selections. Therefore cycle times
will vary. Unexpected events in a wash cycle (eg out of balance, oversudsing) can lengthen
the cycle time.
Progress lights
The progress lights indicate what part of the cycle the washer is currently on (wash, rinse
or spin). All three lights are on at the beginning of the cycle. The light for the current part
of the cycle flashes, and each one goes out when that part of the cycle iscomplete.
Keylock mode
Keylock can be used to lock the buttons on your washer. This will avoid accidental button
pushes. For more detail please refer to ‘Wash cycle options’.
Drum light (WH8560F, WH8060F models only)
Your machine has a drum light to help assist you when loading and unloading your washing
machine. When you press ‘Power’, the LED light in the drum will turn on, after2 minutes it
will automatically turn off. At the end of the cycle, the drum light will turn on again for 5
minutes to help facilitate unloading.
CONTROL PANEL

15
CONTROL PANEL
WH8560F and WH8060F models
1POWER Press to turn the washer ON/OFF.
2Keylock Touch to disable all buttons on the display panel, except the
‘Power’ button. This prevents accidental button presses.
3SmartTouch™
Control Dial
Rotate to select your desired wash cycle.
zRed LED illuminates to indicate the selected wash cycle.
4Digital display
screen
Shows the following:
z‘Time to go’ – the remaining time in the cycle that is
currently running.
zDelayed start time of wash cycle.
zNotifications if an error is detected or a warning is necessary.
5Progress lights Indicate the current status of the wash cycle.
zAll lights are illuminated at the start of the wash cycle.
zThe light of the current status flashes, and then turns off
oncecompleted.
6Delay Start Touch toincrease or decrease the delay start time.
7Time Saver Touch toturn Timer Saver on or off.
8Wash Temp Touch to increase or decrease wash water temperature.
9Spin Speed Touch to increase or decrease washer spin speed.
!0 Options Touch to select Eco Rinse, Wrinkle Free and/or Soak.
!1 Wash Boost Touch to select Pre Wash or Rinse+.
!2 Add a Garment Touch to interrupt the wash part of the cycle to add or remove
agarment.
!3 START/PAUSE Touch to start or pause the selected wash cycle.
1
2 8 9 !0 !1 7!2
!3
53
6
4

16
WH8560P, WH8060P and WH7560P models
CONTROL PANEL
1POWER Press to turn the washer ON/OFF.
2Keylock Touch to disable all buttons on the display panel, except the
‘Power’ button. This prevents accidental button presses.
3SmartTouch™
Control Dial
Rotate to select your desired wash cycle.
zRed LED illuminates to indicate the selected wash cycle.
4Digital display
screen
Shows the following:
z‘Time to go’ – the remaining time in the cycle that is
currently running.
zDelayed start time of wash cycle.
zNotifications if an error is detected or a warning is necessary.
5Progress lights Indicate the current status of the wash cycle.
zAll lights are illuminated at the start of the wash cycle.
zThe light of the current status flashes, and then turns off
oncecompleted.
6Delay Start Touch toincrease or decrease the delay start time.
7Wash Temp Touch to increase or decrease wash water temperature.
8Spin Speed Touch to increase or decrease washer spin speed.
9Soil Level Touch to select the level of soil in your load.
!0 Wash Boost Touch to select Pre Wash or Rinse+.
!1 Options Touch to select Eco and/or Wrinkle Free.
!2 Add a Garment Touch to interrupt the wash part of the cycle to add or remove
agarment.
!3 START/PAUSE Touch to start or pause the selected wash cycle.
1
2 8 9 !0 !1 7!2
!3
53
6
4

17
CONTROL PANEL
WH9060J, WH8560J, WH8060J and WH7560J models
1POWER Press to turn the washer ON/OFF.
2Keylock Touch to disable all buttons on the display panel, except the
‘Power’ button. This prevents accidental button presses.
3SmartTouch™
Control Dial
Rotate to select your desired wash cycle.
zRed LED illuminates to indicate the selected wash cycle.
4Digital display
screen
Shows the following:
z‘Time to go’ – the remaining time in the cycle that is
currently running.
zDelayed start time of wash cycle.
zNotifications if an error is detected or a warning is necessary.
5Progress lights Indicate the current status of the wash cycle.
zAll lights are illuminated at the start of the wash cycle.
zThe light of the current status flashes, and then turns off
oncecompleted.
6Delay Start Touch to increase or decrease the delay start time.
7Wash Temp Touch to increase or decrease wash water temperature.
8Spin Speed Touch to increase or decrease washer spin speed.
9Wash Boost Touch to select Pre Wash or Rinse+.
!0 Options Touch to select Eco.
!1 START/PAUSE Touch to start or pause the selected wash cycle.
1
2 8 9 !07
!1
53
6
4

18
WASH CYCLES
Your washer has a number of wash cycles to suit your laundering needs. Selecting the most
appropriate cycle for each particular wash load will help ensure you get the best wash result.
CYCLE DESIGNED FOR DESCRIPTION
MAX.
LOAD
SIZE
(KG)*
DEFAULT
WASH
TEMP.
(°C)
MAX.
WASH
TEMP.
(°C)
DEFAULT
SPIN
SPEED
(RPM)
MAX.
SPIN
SPEED
(RPM)
Cottons** Normally soiled everyday
cotton loads, eg whites.
A comprehensive cycle
specifically designed for
cottons.
8.5 or
8.0 40 90 1400 1400
Everyday Mixed everyday items,
eg towels, sheets,
sweatshirts, t-shirts.
A cycle designed for
mixed loads. 8.5 or
8.0 40 90 1400 1400
Heavy Heavy soiled durable
garments eg tea towels,
rugby shorts.
A stronger, hotter wash for
more durable items. 8.5 or
8.0 60 90 1400 1400
Delicate Delicate, lightly soiled
items, eg tops, blouses.
Gentler wash with more
water to look after delicate
items.
440 60 500 800
Easy Iron Minimising creasing eg
shirts, trousers.
Less spinning with
‘Wrinkle Free’ option to
help minimise the need
for ironing.
440 60 800 800
Bulky Washing bulky items. A warm, gentle wash and
slow spin for special care
of bulky items.
460 90 800 800
Allergy Asthma sufferers
and people with
skin sensitivities.
Hot wash to kill dust mites
and extra rinses to remove
all traces of detergent.
8.5 or
8.0 60 90 1400 1400
Wool*** Machine washable
woollen items.
Extra gentle wash action
that complies with
Woolmark Apparel Care
criteria.
240 40 800 800
Super
Quick
Freshening up small musty
or lightly soiled items.
A quick cycle for small
lightly soiled loads. 230 60 800 1400
Sports Cotton/synthetic
sports clothing.
A cycle tailored to washing
sports type clothing. 440 40 1100 1400
Rinse Items that require
rinsing only.
Two rinses followed by
a spin.
8.5 or
8.0 Cold Cold 1400 1400
Spin Spinning wet items. Spin only. 8.5 or
8.0 n/a n/a 1400 1400
Drum
Clean
Maintaining the cleanliness
of your washer.
A hot cycle to remove any
residues inside the washer. n/a 90 90 1400 1400
*Depends on your model of washer (8.5kg or 8.0kg capacity).
**‘Cottons’, ‘40°C’, ‘1400rpm’, ‘Eco Rinse’ selected is the recommended water and energy saving
cycle for normally soiled, everyday washing.
WH8560F and WH8060F models
***Woolmark Apparel Care – The wool wash cycle of this machine has been approved
by The Woolmark Company for the washing of machinewashable wool products
provided that the products are washed according to the instructions on the garment
label and those issued by the manufacturer of these washing machines M1528.
Only the WH8560Fand WH8060F models comply with Woolmark Apparel Care
requirements.