Fisher & Paykel WH1060P1 User manual

Installation Instructions
Accessories
Check if you received the following accessories with your Fisher & Paykel washer. You will find them inside the drum or
attached to the packaging.
• 2 x Inlet hose(s)
• 1 x Inlet valve cap
• 1 x Drain hose guide
• 1 x Installation guide and User guide
• 1 x Spanner
• 1 x Installation leaflet (attached to the top of the washer)
Unpacking
To ensure the best performance from your new washer follow the instructions below.
Removing the Packaging
1. Remove the outer packaging (including the expanded polystyrene packer and plastic wrapping). All packaging
must be removed prior to use. Ensure these materials are kept out of reach of children. Note: a small amount of
water may be seen inside the packaging and inside the washer. This is the result of factory testing and is
normal.
2. Tilt the machine backwards and ‘walk’ it off the base one foot at a time. Not doing so may cause damage to
your floor and washer.
3. Remove all packaging and accessories from inside the drum.
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/WashSmart/WH1060P1/User_Guide_WH1060P1/03_Installatio…
Updated: Mon, 06 Apr 2020 08:08:16 GMT
Powered by
1

Removing Transit Safety Bolts
The clothes washer is fitted with transit safety bolts at the rear to avoid possible damage to the interior during
transportation.
The transit bolts MUST be removed prior to operation of the machine.
Failure to remove these will result in damage to the machine.
The transit bolts MUST be removed in order to use the power cord.
To Remove the Bolts
1. Use a spanner or socket to unscrew and remove all 4 transit bolts at the back of the washer (A).
2. Pull the black rubber grommets to remove the bolt, grommet and white plastic spacers from the machine (B).
Retain these for future use.
Removing the transit safety bolts
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/WashSmart/WH1060P1/User_Guide_WH1060P1/03_Installatio…
Updated: Mon, 06 Apr 2020 08:08:16 GMT
Powered by
2

3. Detach
the drain
hose from
the plastic
clasp, and
remove
the clasps
on the
side of the
transit
braces.
4. Remove
the 10
transit
brace
screws
from the
left and
right
sides, and
near the
centre of
the top
brace
(refer to
C).
5. Remove
the braces
(refer to
D).
Keep the
braces
and
screws for
future use.
6. Pull out
the two
transit
rods
located
below the
two lower
transit bolt
holes and
retain for
future use
(refer to
E).
7. Remove
Removing the drain hose
Removing the transit brace screws Removing the braces
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/WashSmart/WH1060P1/User_Guide_WH1060P1/03_Installatio…
Updated: Mon, 06 Apr 2020 08:08:16 GMT
Powered by
3

the yellow
safety clip
from the
power
cord.
8. Cover the
transit bolt
holes with
the plastic
plugs
(provided).
Push to
clip into
place
(refer to
F).
Removing the transit rods
Covering bolt holes with plastic plugs
Product Dimensions
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/WashSmart/WH1060P1/User_Guide_WH1060P1/03_Installatio…
Updated: Mon, 06 Apr 2020 08:08:16 GMT
Powered by
4

FRONT VIEW
TOP VIEW
Product Dimensions mm
A. Overall height of product 850
B. Overall width of product 600
C. Overall depth of product (including dial and door when closed) 665
D. Depth with door open 1110
E. Minimum door clearance to adjacent wall 340
Standpipe or spigot height 600 – 1000
Maximum Capacity kg
WH1060P1 10
WH1260P1 12
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/WashSmart/WH1060P1/User_Guide_WH1060P1/03_Installatio…
Updated: Mon, 06 Apr 2020 08:08:16 GMT
Powered by
5

The exact height of your washer is dependent on how far the feet are extended from the base of the
machine. The space where you install your washer needs to be at least 40mm wider and 20mm
deeper than its dimensions.
• Electrical supply: 220 – 240V, 50Hz sinusoidal, minimum 10A.
• Inlet water static pressure: Max. 1MPa (150psi), Min. 30kPa (4.5psi).
• Inlet water flow rate at tap: Min. 6 litres/min.
Location
Install the machine on a solid and level floor surface ensuring it has at least 20mm clearance on each
side. The washer must not be installed on any soft or textured floor coverings (eg carpet, rugs).
This machine must not be installed and operated on a plinth.
Levelling the Washer
Level the washing machine to ensure good spin performance, and to minimise noise, vibrations and
wear and tear on the washer.
1. Before positioning the washer in its final position, check that it
is level, front to back and side to side.
2. Adjust the washer into its final position (we suggest a minimum
clearance of 20mm each side).
3. Use a spirit level to check that the washer is correctly level. If
needed, pull the washer out. Loosen the lock nut using the
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/WashSmart/WH1060P1/User_Guide_WH1060P1/03_Installatio…
Updated: Mon, 06 Apr 2020 08:08:16 GMT
Powered by
6

spanner provided and wind the feet up or down to correctly
level the machine.
4. Using the spanner provided, tighten the lock nuts against the
base of the washer to lock the feet in position.
Locking the feet
Connecting to the water supply
Inlet Hoses
• Use new hose sets provided with the washer to connect the washer to the water mains.
• Old hose sets should not be re-used.
• We recommend the inlet hoses are changed every 5 years.
Failure to do so may result in a flood and damage to property.
1. Connect the straight ends of the inlet hoses to the taps.
2. Connect the elbow ends to the corresponding machine
inlet valves. The hot valve is coloured orange to make
this easier.
3. Tighten the inlet hose ends by hand until the hose seal
just makes contact with the tap sealing face. Continue to
tighten a further half-turn. Make sure there are no kinks
in the hoses.
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/WashSmart/WH1060P1/User_Guide_WH1060P1/03_Installatio…
Updated: Mon, 06 Apr 2020 08:08:16 GMT
Powered by
7

4. Turn the taps on and check for leaks. Check for leaks
again after 24 hours.
Straight (tap) Elbow (machine)
Inlet hose ends
The hot water temperature should not exceed 65°C and the cold water temperature not
exceed 35°C. Temperatures above these may cause the washer to fault or cause damage
to the machine.
If you have an uncontrolled water heating source (eg a wet back or solar heating system) you should fit a Hot ‘N’ Safe
Valve. This will ensure the hot water temperature remains within safe limits.
Hot ‘N’ Safe Valves available are:
RMC TVA 50HF
MC TVA 75HFS
Adjustable between 35°C – 55°C
RMC TVA 50HP
For instantaneous gas hot water supply
Water supply requirements:
• Inlet water pressure: Maximum 1MPa (150psi), Minimum 30kPa (4.5psi)
• Inlet water flow rate: Minimum 6 litres/minute.
Cold supply only:
If you only have a cold water supply, the inlet valve cap (blanking cap) that came with your washer must be connected to
the hot inlet valve. The cap prevents water leaking out of the hot valve. This appliance incorporates backflow protection
complying with IEC61770. No further backflow protection is required for connection to the water supply.
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/WashSmart/WH1060P1/User_Guide_WH1060P1/03_Installatio…
Updated: Mon, 06 Apr 2020 08:08:16 GMT
Powered by
8

Your washer has an internal heater to heat water. If you do not connect a hot water inlet hose, your
washer will automatically recognise there is no hot water supply and its internal heater will heat the
cold water to the selected cycle temperature.
Draining
Placing The Drain Hose in a Standpipe or Tub
1. To guide the drain hose over the tub or standpipe,
the hose guide must be fitted to the drain hose.
The height of the standpipe or tub should be
between 600 – 1000mm.
2. Secure the hose guide so it cannot be dislodged
from the standpipe or tub.
• If the drain hose is placed
on the ground or if the
standpipe or tub is less
than 600mm high, the
washing machine will
continuously drain while
being filled (siphon).
• Regularly check that your
standpipe or tub is free
from lint or other
obstructions, which may
affect how your machine
works or may cause
flooding.
Fitting the drain hose guide
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/WashSmart/WH1060P1/User_Guide_WH1060P1/03_Installatio…
Updated: Mon, 06 Apr 2020 08:08:16 GMT
Powered by
9

Attaching Drain Hose to Spigot
1. Guide the drain hose through the hose guide.
2. Secure the hose guide to the back wall of
cupboard using a screw. The height of the drain
hose should be between 600 – 1000mm from
ground level.
3. Attach the drain hose to the spigot and secure
using a hose clamp to ensure the blanking insert is
cleared from the spigot.
4. Check for leaks.
• The drain hose should be checked from time to time
and replaced if any damage (eg wear, cuts, bulges,
kinks, leaks, etc) is found. Do not bend the drain
hose sharply, as this may cause it to split.
• In multi-storey apartments or any upper floor, the
machine should be installed on a floor equipped
with a drain.
• Draining must comply with local by-laws.
Attaching drain hose to spigot
Electrical Connection
1. This appliance must be connected to a 220V – 240V, 50Hz, sinusoidal, minimum 10A electrical supply.
2. Release the power cord (transit bolts must be removed).
3. Remove and discard the plastic pin cover and plug into a wall socket.
4. Connect the appliance to an earthed outlet protected by a fuse of suitable capacity.
• Check the power cord for damage and make sure it is not squashed or twisted when installing the washer.
• Always remove the power cord from a socket by the plug, not by the cord.
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/WashSmart/WH1060P1/User_Guide_WH1060P1/03_Installatio…
Updated: Mon, 06 Apr 2020 08:08:16 GMT
Powered by
10