Fisher-Price Signature RTA Dresser User manual

IMPORTANT! Please keep these instructions for future reference. Please read
these instructions before assembly and use of this product.
• Adult assembly is required.
• Allen wrench (included) required for assembly.
• Product features and decorations may vary from illustrations.
• Do not use power drills or drivers.
• Phillips Head Screwdriver (Not included) required for assembly.
Bulletin NO.: 120310-00-EN
EN
fisher-price.com

Part List
A. Left Side Panel x1
2
B. Right Side Panel x1 D. Top Panel x1
E2. Bottom Front Rail x1E1. Top Front Rail x1 E3. Lower Front Rail x2
C. Divider Frame x1
F2. Lower Back Rail x1
G2. Bottom Back Panel x1 (Large)G1. Top Back Panel x1 (Small)
H3. Left Drawer x6
H2. Drawer Back x6
H4. Right Drawer x6 H5. Drawer Bottom x6 H6. Drawer Support x12
F3. Back Thick Panel x1
E4. Front Molding x1
H1. Drawer Front x6
F1. Top Back Rail x1

Part List
HARDWARE AND TOOL DIAGRAM
3
I 1-3/4" Allen Head Bolt x24
Plastic Crescent Washer x12
K
Wood Dowel x22
L
N 1" Phillips Head Screw x60
O 5/8" Phillips Head Screw x39
1" Knob Bolts x12
P
Drawer Knob x12
Q
Anti-Tip Kit x 1bag
(Instruction and Hardware inside)
Plastic bag
M
Allen Wrench x1
R
1-1/8" Allen Head Bolt x20
J

4
Furniture Care Instructions
Room Climate Control
Wood, when first cut contains more than 50 percent water. When it is prepared for furniture
construction it is placed in a Kiln and the mois
ture content is brought down to 8 to 10 percent. Wood
is porous and responds to its environment. If the room has high humidity it will absorb it and expand
and if the humidity is low it will lose mois
ture and shrink.
It is important that the humidity levels in the room be controlled from extremes of too much
humidity or too little. Furniture should not be placed close to air-conditioning outlets, fireplaces,
radiators, space heaters, humidifiers or dehumidifiers. Exposure to extreme variations of
temperature and humidity can damage any fine wood product.
The Ideal Environment for Fine Furniture
Fine wood furniture will have fewer problems when its environment is controlled at a temperature
between 65 and 75 degrees and a relative humidity between 35 and 40 percent. Wood placed in an
environment outside of those limits can and will shrink or expand and may develop some small
cracks which are not material or structural defects.
Sticking Doors and Drawers
With minor changes in temperature and humidity, doors and drawers may swell and be
difficult to open or close. Tolerances have been built into the units but extreme conditions may still
cause sticking. This will adjust back to normal over time but until it does, consider using a
dehumidifier or rub candle wax or paraffin on the sides that stick.
Avoid Direct Sunlight
Keep the furniture out of direct sunlight. Ultraviolet rays will fade colors and in some cases
darken them. It can also cause crazing or hair line cracks in the finish. White finishes will yellow
naturally over time and exposure to direct sunlight will hasten this natural process along with some
woods darkening naturally over time; this is not considered to be a quality defect.
Proper Storage
If you need to put your furniture in storage for any period of time, do not place furniture in a damp
basement or hot dry attic. Allow air movement around the furniture and do not stack anything on it.
In General
Protect furniture surface from hot or extremely cold items.
Use coasters under hot or cold beverages.
Do not use synthetic fabric under accessories or lamps.
Protect tops from pens, markers and crayons.
Oils from potpourri and other scented items can damage the furniture finish.
Do not drag items across the surface of the furniture.
Allow the surface to breath by rotating your accessories and lamps.
Do not over polish the furniture, do it only two or three times a year. Over polishing can
dis
tort the natural finish of the product.
Do not wax the furniture as wax build up can destroy the natural finish of the product.
When moving furniture always lift the unit. Do not push or drag it to avoid damage to the legs.
Keep the furniture level so doors and drawers open and close freely.
Clean with a damp, not wet, cloth. Use only a mild soap. Do not use abrasive cleaners.

5
STOP
IF YOU EXPERIENCE ANY
ISSUES WITH THIS PRODUCT
BEFORE YOU
RETURN THIS TO
THE RETAILER
PLEASE FOLLOW
PROCEDURES ON THE
BACK PAGE

Assembly Step 1
6
E2. Bottom Front Rail x1E1. Top Front Rail x1
F2. Lower Back Rail x1 F3. Back Thick Panel x1
F1. Top Back Rail x1
Wood Dowel x20
L
E1
E2
F1
F2
F3
L
L
L
L
L
L
L
L
L
L

7
Assembly Step 2
C. Divider Frame x1
E1. Top Front Rail x1 E2. Bottom Front Rail x1 E3. Lower Front Rail x2
F2. Lower Back Rail x1 F3. Back Thick Panel x1
F1. Top Back Rail x1
I 1-3/4" Allen Head Bolt x2 1-1/8" Allen Head Bolt x6
J Allen Wrench x1
R
J
C
E3
J
E2
C
F3
C
J
J
F3
F2
F1
E2
E3
E1
E3
I
II
R
C
F1
J
C

Assembly Step 3
8
A. Left Side Panel x1
I 1-3/4" Allen Head Bolt x6 1-1/8" Allen Head Bolt x2
J
Allen Wrench x1
R
Plastic Crescent Washer x6
K
K
I
F1
F2
F1
F3
E2
E3
E1
A
K
I
F3
J
E3
C
K
I

Assembly Step 4
9
I 1-3/4" Allen Head Bolt x6 1-1/8" Allen Head Bolt x2
J
Allen Wrench x1
R
Plastic Crescent Washer x6
K
B. Right Side Panel x1
F1
E1
E3
E2
K
I
F1
J
E3
F3
A
C
B
B
B
K
I
K
B
F3
I
K

Assembly Step 5
D. Top Panel x1
D
J
10
I
I 1-3/4" Allen Head Bolt x10 1-1/8" Allen Head Bolt x4
J
Allen Wrench x1
R
I
I
I
I
II
J
J
E2
C
A
B
J
I
I
J
R B
F1 E1
D

Assembly Step 6
1-1/8" Allen Head Bolt x6
J Wood Dowel x2
L
Allen Wrench x1
R
11
E4
J
J
JJ
B
A
L
L
LL
E4
E4
E4. Front Molding x1

12
Assembly Step 7
G2. Bottom Back Panel x1 (Large)
G1. Top Back Panel x1 (Small)
O 5/8" Phillips Head Screw x39
Label
O
G2
G1

Assembly Step 8
13
H2
H3
H4 H5
H6
N
Note: Grooves on Drawer Sides and Drawer Back should all face
inward to allow Drawer Bottom to be inserted. Glides should be on the
bottom outside of box.
H1
P
Q
N
N
N
N
H3. Left Drawer x6 H4. Right Drawer x6
H5. Drawer Bottom x6
H6. Drawer Support x12
H1. Drawer Front x6
H2. Drawer Back x6
N
1" Phillips Head Screw x60
1" Knob Bolts x12
P
Drawer Knob x12
Q
H3
H4
H2
H1
H4
H2
H1
H5
H3
Q
H2
H3
H4
H6

Assembly Step 9
14
Plastic bag
Anti-Tip Kit x 1bag
(Instruction and Hardware inside)
M
WARNING LABEL
Note: Please follow instructions
in Anti-Tip Kit when assembly is
complete.
Plastic bag
Drawer

15
MADE IN VIETNAM
FISHER-PRICE
TM
and associated trademarks are owned by and used
under license from Mattel.©2018 Mattel. All Rights Reserved.
Manufactured for and dis
tributed in the United States & Canada by Bivona & Company®, LLC
125 Jackson Anvenue Suite 1, Edison, NJ 08837
Mos t inquiries can be answered by visiting our website www.bivonaco.com
There, you can order parts, find assembly ins
tructions, and get answers
to frequently asked ques
tions on all of our brands.
You can also email us at [email protected]
In order for us to provide you with the bes
t service possible, please include the
following information in your email:
1. Your Name
2. Address
3. Phone Number
4. Item Number and description of your product
5. PO#
6. Production Date
All product information will be on the product label located on the back of
all dressers and other furniture, and on either the inside bottom of the headboard, crib
ends, or s tabilizer bar of your crib, depending on which model you have.
Someone will contact you via e-mail or phone to help you with your issues.
If you do not have internet access, you can fax your information to 732-527-0664
If you do not have internet or fax access, please call us at our toll free number 1-888-963-8125.
Be sure to have all of the above information ready to give to your Cus
tomer Service Specialis t.
Product Assis tance Procedures
Procedures to follow should you have any ques tions:
You have purchased a quality piece of furniture. Our International team has spent many
hours designing and engineering this piece and packaging to ensure you will be satisfied
with your purchase. But if for any reason you need help with your purchase please contact
us at any time.
Contact
CanadaU.S.A
Bivona & Company®, LLC
125 Jackson Avenue Suite 1,
Edison, NJ 08837
Toll Free: 1-888-963-8125;
Fax: [phone]
Website: www.bivonaco.com
Email: [email protected]
Bivona & Company®, LLC
125 Jackson Avenue Suite 1,
Edison, NJ 08837
Toll Free: 1-888-963-8125;
Fax: [phone]
Website: www.bivonaco.com
Email: [email protected]