Flair Furnishings Slick Triple Bunk User manual

PRODUCT SIZE : 920mm x 1930mm,1220mm x 1930mm
Thank you for purchasing this product. Before starting assembly we suggest you spend a short time reading
through this leaflet, then follow the simple step by step guide.
Two persons are needed to assemble this product.
ASSEMBLY INSTRUCTIONS
MODEL
: Slick Triple Bunk
1
27
* Approximately 2 Hours
* 2 People Required
* WARNING : Top Bunks and elevated Beds are dangerous and are not recommended for children
under the age of 6.
The upper bunk must be more than 2 m from any ceiling fan.
IMPORTANT INFORMATION
1. This bunk bed is suitable for a single mattress or foam bed 920mm x 1870mm.Thickness of mattress should not exceed 200mm.
2. Children should be discouraged from playing on this bunk bed.
3. The bunk bed should be checked periodically by the owner to ensure that the guardrail, ladder and other components are
maintained in the correct position and state of repair and that all connectors are tight.
4. A bunk bed is not to be placed near a ceiling fan unless the distance between the closest points on the ceiling fan and bunk
bed is at least 2 metres.
5. Use guardrails on both sides of upper bunk.
6. Prohibit horseplay on or under bed(s).
7. Prohibit more than one person on upper bunk.
8. Use ladder for entering and leaving upper bunk.
9. If the bunk bed will be placed next to the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and the wall.
10. Fall from elevated beds can be fatal and death have occurred where children have fallen from elevated beds. This is
relevant for all ages.The risk is greater for younger children.
The risk of injury or death from a fall from an elevated bed compared to a non elevated bed is :
10 x greater for 7-8 year olds
7 x greater for 9-10 year olds
3 x greater for 11-12 year olds
11.Top Bunks and elevated Beds are dangerous and are not recommended for children under the age of 6.
STRANGULATION HAZARD:
12. Never attach or hang items to any part of the bunk bed that are not designed for use with the bed for example, but not limited to
hook, belt, and jump ropes.
Tools Required For Assembly
Philips Screw Driver
DO NOT USE POWER TOOLS
TO ASSEMBLE THIS PRODUCT.
USE OF POWER TOOLS WILL
INVALIDATE ANY CLAIM AND
MAY DAMAGE THIS PRODUCT
MAKING IT UNSAFE.
DO NOT USE HAMMER
Tools Not Use

PARTS LIST
Pcs
Part Name
No.
Carton 1 of 4
2
27
Model: Slick Triple Bunk
FITTING LIST
Carton 2 of 4
03 RIGHT PANEL FRONT 1
10 SIDE PANEL LOWER (TOP FRONT) 1
11 1
SIDE PANEL UPPER(TOP FRONT)
12 SIDE PANEL BOTTOM FRONT 1
42 2
43 1
44 4
BED SUPPORT METAL
BED CENTER SUPPORT LEG
BASE SUPPORT RAIL
RIGHT PANEL BACK
02 1
SUPPORT PANEL UPPER (OPEN SHELF)
04 1
BOTTOM PANEL (OPEN SHELF)
05
SUPPORT PANEL SMALL LEFT (OPEN SHELF)
06 2
2
BACK PANEL (OPEN SHELF)
07
LEFT PANEL BACK
08 1
2
14
1
SUPPORT PANEL RIGHT
13 SUPPORT PANEL LEFT 1
SUPPORT PANEL SMALL RIGHT (OPEN SHELF)
25 2
26 4
CENTER PANEL (OPEN SHELF)
SUPPORT PANEL LOWER (OPEN SHELF)
27 1
Carton 3 of 4
CENTER PANEL UPPER
01 1
09 LEFT PANEL 1
17 LADDER LEFT PANEL 1
20
1
BOTTOM PANEL (DRAWER)
21 1
BACK PANEL (DRAWER)
22 LEFT PANEL (DRAWER) 1
40 DOOR 2
41 DOOR 1
46 LADDER LEFT PANEL 1
Carton 4 of 4
15 LADDER BOTTOM PANEL 1
16 LEFT PANEL (1ST LADDER STEP) 1
18 RIGHT PANEL (1ST LADDER STEP) 1
19 BACK PANEL LADDER 1
30 TOP PANEL LADDER 1
31 RIGHT PANEL (2ND LADDER STEP) 1
32 LEFT PANEL (2ND LADDER STEP) 1
33 2
34 1
35 RIGHT PANEL (3RD LADDER STEP) 1
36 1
37 1
38 LADDER BACK PANEL 1
39 LADDER LEFT PANEL 1
29 16
45 16
LVL SLAT BASE (SHORT)
LVL SLAT BASE (LONG)
BACK PANEL LADDER
TOP PANEL LADDER
LEFT PANEL (3RD LADDER STEP)
TOP PANEL LADDER
23 RIGHT PANEL (DRAWER)
24 FRONT PANEL (DRAWER)
28 CENTER PANEL LOWER
1
1
1

PARTS LIST 27
3
Model: Slick Triple Bunk
26
09 08 04
07
05
06
26
02
13
03
10
45
44
29
22 21
20
23
24
43
42 x2
12
x16
x4
x16
25
27
28
06
25
07
05
26
26
14
11
01
17
46
39
38
37
36
35
33
33
18
15
16
30
32
34
31
19
40
41
x2

FITTING LIST 27
4
Model:
Slick Triple Bunk
USEFUL HINTS & TIPS
Two people will be required
to assemble this unit
Please keep this assembly
instruction for future reference
CAUTION
There are many small components used
in the construction of this unit. These
loose items should be kept away from
young children whilst assembling your
unit. As an extra precaution, screw
cover caps should be permanently
fixed in position. (Where applicable)
Fitting List
A89
Pcs
Part Name
No.
B
C
D
G
H
L
N
89
158
20
4
P
Q
16
R
Cam Stud (5137)
Cam
M8 x 25mm Wood Dowel
8
K
37
4
T
4
14
M6 x 12mm Allen Bolt
M6 x 13mm Baller
45mm Chipboard Screw
M6 x 60mm Allen Bolt
6
M6 x 35mm Allen Bolt
M6 x 25mm Allen Bolt
25mm Plate Nylon Castes
M6 x 40mm Wood Dowel
M6 x 50mm Allen Bolt
M6 JCN Nut
10
PVC L Bracket (White Colour)
8
V
Metal Support Plate (White)
2
W
M6 Allen Wrech
2
M6 x 40mm Allen Bolt
2
Y
Hinges Arm
6set
M
X
15mm Chipboard Screw
F76
M6 x 15mm Allen Bolt
J
M6 x 30mm Allen Bolt
64
4
S

5
GUIDE TO ASSEMBLY 27
Model: Slick Triple Bunk
STEP 1
01
04
27
28
05 x2
07 x2
26 x4
WHEN FITTING CAMS
ENSURE STARTING POSITION IS CORRECT
BEFORE YOU INSERT CONNECTING BOLT
TURN CLOCKWISE UNTIL SECURE
CORRECT WRONG
C
B x 34
C x 56
A x 6