Flash butrym F7000490 User manual

www.flash-butrym.pl Page 1
4 MINI MOVING HAED BEAM
4X10W WHITE LED
F7000490
USER MANUAL

www.flash-butrym.pl Page 2
Catalogue
IWarning……………………………………………….1
II Statement……………………………………………….1
HI Safety Precautions………………………….…………..1
IV Technology Parameter………………………..………..2
VWarning for Replace Lam…………………..…………3
VI Warning for Operation…………………………..……..4
VII Sketch map of Connection……………………………4
VIII Menu Function……………………………………….……5
IX Channels Control……………………………………..……6

www.flash-butrym.pl Page 3
Warning
To reduce the risk of electrical shock or fire, do not expose this unit to rain or
moisture.
Do not spill water or other liquids into or on
to your unit.
During long periods of non-use, disconnect the unit’s
main power.
It should be installed in a well-ventilated place,
at a distance of 50 centimeters or more with the walls.
At the same time, please check if the fan and ventilation holes are unobstructed.
Statement
The product has perfect performance and intergrity packing. All users should be
strictly comply with the warning and operating instructions as stated. Or we aren’t in
charge of any result by misusing. Any damage resulting by misuse is not within the
company’s warranty. Any fault or problem caused by Note: All information is subject
to change without prior notice.
Safety Precautions
In order to guarantee the product’s life, please don’t put in the damp places or even
the environment over 40degress.
Always mount this unit in safeand stable matter.
The qualified professionals are allowed to carry
out the lamp installation, operation and maintenance, but they must guarantee to
operate in strict accordance with the instructions referred to.
Using lamp, the change rate of Power voltage should
be within+10%, If the voltage is too high, it will shorten
the light’s life; if it’s not enough, the lamp will be dark.
Please restart it after turning off light for 20 minutes until full-colling. Frequent
switching will reduce the life span of lamps and bulbs; intermittent useing will improve
the life of bulbs and lamps.
In order to make sure the product is used well, please read the Manual carefully
IV. Technology Parameter
Body
1.Aluminium structure with streamline plastic cover.
2.Device locking Pan and Tilt mechanisms for transportation and maintenance
O Voltage
AC100-240V 50/60HZ

www.flash-butrym.pl Page 4
Scan angle:
Pan=540°, Tilt=250°
Scan speed
Pan=5second, Tilt=3second
Beam angle
angle=0~4°
Control signal
DMX512, 3-Pin DMX Input and output.
Electronics
1.Mechine reset from the control panel or the controller.
2.ON/OFF lamp control from the control panel or the controller.
3.Electronic monitoring with status error.
4. Power supply: AC 100V - 240V, 50/60Hz
5. Maximum power consumption: 120W
Product Specifications:
4pcs 10W white LED lamp beads
80,000 hours of lifespan
4pcs mini moving head light, individually controllable
Fast and accurate horizontal / vertical rotation
Horizontal 540°, vertical 270°
Scan position memory function , automatic reset function
Superior beam effects
Dedicated 8°advanced optical system
Efficient LED light off , speed controllable
20 times/s high-speed stroboscopic
0-100% smooth linear dimming
Macro function
7CH/22CH can be switched
DMX512, master-slave , voice ,self-propelled operation
LED display
Efficient low-noise cooling system
Power-con power input and output
3 –pin XLR signal connector input and output
INSTALLATION
1. Indoor use only
2. Mounting head in any position
3. Minimum distance to illuminated surfaces: 3m
4. Keep a minimum distance from the surrounding area of the head: 0.5 m
CONNECTORS
1. Power connector IN: Neutrino Power Con
2. Mains connector OUT: Neutrino Power Con
3. DMX512 signal connector: 3-pin XLR (IN, OUT), and 5-pin XLR (IN, OUT)

www.flash-butrym.pl Page 5
ACCESSORIES INCLUDED
1. Power-Con power cable IN
2. Power-Con power cable OUT
3. DMX512 cable - XLR 3pin
4. DMX512 cable - XLR 5pin
5. User manual
Safety Devices
1.Bipolar circuit breaker with thermal protection.
2.Automatic break in power supply in case of overheating or failed
operation of cooling system.
3.forced ventilation with axial fans.
Weight
1.Net Weight: 10kg
2.Gross Weight: 11kg
Main Feature
Voltage：AC100-240V. 50/60HZ
Supply consumption：120W
Led Source: 4pcs LUMILUX White LED 10W
Cooling system：convection cooling
Dimmer：0~100％
Strobe：0~20 times/sec, various of strobe effect
Control mode：DMX 512/sound active/Master-Slave/automatic
Display：Digital display screen
Channel：7CH/22CH
Scan speed：Pan 540º，Tilt 270º/Speed adjustable
Scan Position：reposition auto after unexpected movement, electronic auto
position correction
Weight：11KG