Flotec E75STVT User manual

OWNER’S MANUAL
Submersible Solids
Handling Pumps
NOTICE D’UTILISATION
Pompes submersibles
pour les matières solides
MANUAL DEL USUARIO
Bombas submergibles para el
manejo de líquidos con sólidos
Installation/Operation/Parts
For further operating, installation,
or maintenance assistance:
Call 1-800-365-6832
English . . . . . . . . . . . . . . . Pages 2-6
Installation/Fonctionnement/Pièces
Pour plus de renseignements
concernant l’utilisation,
l’installation ou l’entretien,
Composer le 1 [phone]
Français . . . . . . . . . . . . Pages 7-11
Instalación/Operación/Piezas
Para mayor información sobre el
funcionamiento, instalación o
mantenimiento de la bomba:
Llame al 1-800-365-6832
Español . . . . . . . . . .Páginas 12-16
P.O. Box 342, Delavan, WI 53115
Phone: [phone]
Fax: [phone]
E-Mail: [e-mail]
Web Site: http://www.flotecwater.com
©2010 FP893 (Rev. 7/8/10)
5794 0308
Model E75STVT

Safety / Specifications / Performance / Installation 2
READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for
one of the following signal words and be alert to the
potential for personal injury:
warns about hazards that will cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which
are important but not related to hazards.
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
1. Read this manual carefully. Failure to follow these
instructions could cause serious bodily injury and/or
property damage.
2. Check your local codes before installing. You must
comply with their rules.
3. Vent sewage or septic tank according to local codes.
4. Do not install pump in any location classified as
hazardous by National Electrical Code, ANSI/NFPA
70-1990.
Hazardous voltage. Can shock, burn or
cause death. During operation, the pump is in water.
To avoid fatal shocks, proceed as follows if pump needs
servicing:
5A. Disconnect power to outlet box before unplugging
pump.
5B. Take extreme care when changing fuses or resetting
circuit breakers. Do not stand in water or put your
finger in fuse socket.
5C. Do not modify cord and plug. When using cord and
plug, plug into a grounded outlet only. When wiring
to a system control, connect pump ground lead to
system ground.
6. Do not run pump dry. Dry running can overheat
pump, (causing burns to anyone handling it) and will
void warranty.
7. Pump normally runs hot. To avoid burns when ser-
vicing pump, allow it to cool for 20 minutes after
shut-down before handling it.
8. Motor has been filled at the factory with a special oil.
In normal service, motor should not need oiling.
This pump is designed for use in a residential sewage or
septic system only. Use only within design parameters.
NOTICE: This unit is not designed for use in a recirculat-
ing system (such as a waterfall or fountain), or for appli-
cations involving salt water or brine! Use with waterfalls,
fountains, ponds, salt water, or brine will void warranty.
Pump water only with this pump.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
Read this owner’s manual for installation, operation, and
safety information.
INSTALLATION
(See Figure 1 for Typical Installation instructions.)
Pump must be level when operating. If
motor is tilted, internal start/run switch may overheat and
damage motor.
Risk of electrical shock. Can burn or kill.
Do not lift pump by power cord. See “Cord Lift Warning”
on Page 4. Do not hang pump from discharge pipe or
power cord.
1. Install the pump on a solid, level foundation, or in a
sump pit constructed of tile, concrete, steel or plas-
tic. The recommended minimum diameter of the
sump pit is 18" (46cm) diameter and the minimum
recommended depth is 30" (76cm). Check local
codes for approved materials.
NOTICE: Pump should not be installed on clay, earth
or sand surfaces. Clean the area around the pump of
small stones and gravel which could clog the pump.
Keep the pump inlet screen clear.
GPH (LITERS) AT DISCHARGE FT. OF HEAD
5 (1.5m) 10 (3m) 15 (4.6m) 20 (6.1m) 24 (7.3m)
E75STVT 9200 (34,826) 7500 (28,391) 6300 (23,848) 2400 (9,085) 0 (0)
PERFORMANCE
FPSE Full Load Individual Branch Circuit Dual Element Time
Model H.P. Voltage Amps Required (Amps) Delay Fuse Amps
E75STVT 3/4 115 9.0 15 15
SPECIFICATIONS
For parts or assistance, call Flotec Customer Service at 1-800-365-6832

Electrical 3
2. Thread a 2” discharge pipe into the pump 2” NPT
discharge port. Be careful to avoid stripping or cross-
ing threads.
Piping – Effluent Applications
(3/4" or Less Solids)
Piping must be 1-1/2" minimum to carry volume of
pump discharge. Check local codes to determine if a
check valve is required in your system. In cold climates,
check valves are not used to prevent effluent from freez-
ing in piping.
Piping – Sewage Applications
(2" or Less Solids)
In any case, piping must not be smaller than pump
discharge.
When installed in a sewage system, pipe must be capable
of handling semi-solids of at least 2” (5.1 cm) diameter.
The rate of flow in the discharge pipe must keep any
solids present in suspension in the fluid. To meet mini-
mum flow requirements (2 feet (.6 m) per second in dis-
charge line), size pipe as follows:
A Pipe Size Of: Will Handle a Flow Rate Of:
1-1/2” (3.8 cm) 12 GPM (45 LPM)
2” (5.1 cm) 21 GPM (79 LPM)
2-1/2” (6.3 cm) 30 GPM (113 LPM)
3” (7.6 cm) 48 GPM (181 LPM)
NOTICE: Use Teflon™ tape on pipe connections. Do not
use ordinary pipe joint compound on plastic pipe or
pump. Pipe joint compound can attack plastics and dam-
age pump.
3. To reduce motor noise and vibrations, a short length
of rubber hose can be connected into discharge line
near pump using suitable clamps.
4. If the pump discharge line is exposed to outside sub-
freezing atmosphere, then the portion of line
exposed must be installed so any water remaining in
pipe will drain to outfall by gravity. Failure to do this
can cause water trapped in discharge to freeze which
could result in damage to pump.
5. Install a 2” check valve in the horizontal portion of
the discharge pipe. Make certain, the flow indicating
arrow, points away from the pump. This check valve
will keep the water from either running back into the
basin or into the area being pumped out when the
pump is not running. Check valve should be a free
flow valve that will easily pass solids.
NOTICE: For best performance of check valve when han-
dling solids, do not install it with discharge angled more
than 45° above the horizontal. Do not install check valve
in a vertical position as solids may settle in valve and
prevent opening on startup.
6. Drill a 3/16” (4.7mm) hole in discharge pipe about
1"-2” (2.5 - 5.1cm) above pump discharge connec-
tion (but below check valve) to prevent airlocking
the pump.
7. Insert the float switch piggy-back plug into a proper-
ly grounded outlet and the pump plug into the piggy-
back plug.
8. Check the installation by observing the pump opera-
tion through one complete cycle. Make sure that no
parts of the assembly interfere with the float switch.
Risk of flooding. May cause personal injury
or property damage. Failure to make this operational
check may lead to improper operation, premature failure,
and flooding.
ELECTRICAL
Hazardous voltage. Can shock, burn, or
cause death. When installing, operating, or servicing this
pump, follow safety instructions listed below.
1. DO NOT splice the electrical power cord.
2. DO NOT allow electrical cord plug to be submerged.
3. DO NOT use extension cords. They are a fire hazard
and can reduce voltage sufficiently to prevent pump-
ing and/or damage motor.
4. DO NOT handle or service pump while it is connected
to power supply.
For parts or assistance, call Flotec Customer Service at 1-800-365-6832
Figure 1:Typical Installation
Not
to
Scale
2” Check Valve
Mount Horizontally!
Direction
of Flow
2” Discharge
Pipe
18”
30”
Plug Switch into
115V, 3-Prong,
Grounded Outlet
Plug Pump into
Switch Plug
Sewage
Basin
Drill 3/16” Vent
Hole Here
Install the Pump on a
Hard, Level Surface
Float Switch must
Swing Through
Its Entire Arc
6164 0310
TM E.I. DuPont de Nemours and Company Corporation.

Operation / Service 4
5. DO NOT remove grounding prong from plug or mod-
ify plug.To protect against electrical shock, the power
cord is a three-wire conductor and includes a
3-prong grounded plug. Plug pump into a 3-wire,
grounded, grounding-type receptacle. Connect pump
according to electrical codes that apply.
For automatic operation, plug or wire pump into an auto-
matic float switch or pump controller. Pump will run con-
tinuously when plugged directly into an electrical outlet.
Connect or wire pump to its own individual branch circuit
with no other outlets or equipment in the circuit. Size
fuses or circuit breakers according to chart on Page 2.
Risk of electrical shock and fire. Can burn or
cause death. Be sure that power supply information
(Voltage/Hertz/Phase) on pump motor nameplate matches
incoming power supply exactly. Install pump according to
all electrical codes that apply.
OPERATION
NOTICE: Do not allow pump to run in a dry sump. It
will void the warranty and may damage the pump.
An automatic overload protector in the motor will pro-
tect motor from burning out due to overheating/overload-
ing. When motor cools down, overload protector will
automatically reset and start motor.
If overload trips frequently, check for cause. It could be a
stuck impeller, wrong/low voltage, or electrical failure in
motor. If an electrical failure in the motor is suspected,
have it serviced by a competent repairman.
Pump is permanently lubricated. No oiling or greasing is
required.
SERVICE
Hazardous voltage. Can shock, burn, or
cause death. Before removing pump from basin for ser-
vice, always disconnect electrical power to pump and
control switch.
Risk of electrical shock. Can burn or kill.
Do not lift pump by power cord. See “Cord Lift Warning”
below.
Submerge pump in a disinfectant solution (chlorox or
chlorine) for at least one hour before servicing pump.
The pump motor contains a special lubricating oil which
should be kept clean and free of water at all times.
Check operation by filling sump with water and observ-
ing pump operation through one complete cycle.
Risk of flooding. May cause personal injury
or property damage. Failure to make this operational
check may lead to flooding and premature failure.
NOTICE: This unit is not designed for applications
involving salt water or brine! Use with salt water or brine
will void warranty.
REPAIR PARTS
Power Cord: 10’, 115 V ..................................21628B046
Tethered Float Switch..............................PW117-267-TSE
Impeller..........................................................26053B000
Hazardous voltage. Disconnect pump from
electrical power before replacing cord or switch. Do not
remove impeller housing (volute). There are no consumer
serviceable parts inside the pump.
For parts or assistance, call Flotec Customer Service at 1-800-365-6832
1. Attempting to lift or support pump by
power cord can damage cord and
cord connections.
2. Cord may pull apart, exposing bare
wires with possibility of fire or electri-
cal shock.
3. Lifting or supporting pump by power
cord will void warranty.
4. Use lifting ring or handle on top of
pump for all lifting/lowering of pump.
Disconnect power to pump before
doing any work on pump or attempt-
ing to remove pump from sump.
Risk of electrical
shock.
Can burn or kill.
Do not lift pump by
power cord.
WARNING
CORD LIFT WARNING

Troubleshooting / Repair Parts 5
For parts or assistance, call Flotec Customer Service at 1-800-365-6832
A. Pump fails to operate:
B. Pump fails to empty sump:
C. Pump will not shut off:
Risk of sudden starts. Can result in electrical
shock or pinching of hands or tools. If power to pump is on when thermal overload resets, pump may start without
warning. Disconnect power before servicing pump.
1. Check to be sure that power cord is securely plugged into outlet. Disconnect power to
outlet before handling pump or motor.
2. Check to be sure you have electrical power.
3. Check that liquid fluid level is high enough to activate switch or controller.
4. Check to be sure that 3/16" (4.7 mm) vent hole in discharge pipe is not plugged.
5. Check for blockage in pump inlet, impeller, check valve or discharge pipe.
6. Thermal overload may have tripped. Test start pump; if it starts and then stops immediately,
disconnect from power source for 30 minutes to allow motor to cool, then reconnect to
power source. Check for cause of overheating/overloading.
7. Check the float switch operation for maximum possible clearance.
1. Be sure all valves in discharge valve are fully open.
2. Clean out discharge pipe and check valve.
3. Check for blockage in pump inlet or impeller.
4. Pump not sized properly. A higher capacity pump may be required.
5. Check the float switch operation for maximum possible clearance.
1. Check switch or controller automatic floats for proper operation, location and clearance.
See installation instructions for switch/controller.
2. If pump is completely inoperative or continues to malfunction, consult your local
serviceman.
TROUBLESHOOTING

Warranty 6
RETAIN ORIGINAL RECEIPT FOR YOUR RECORDS.
LIMITED WARRANTY
FLOTEC warrants to the original consumer purchaser (“Purchaser” or “You”) of its products that they are free from defects in
material and workmanship for a period of twelve (12) months from the date of the original consumer purchase.
If, within twelve (12) months from the original consumer purchase, any such product shall prove to be defective, it shall be
repaired or replaced at FLOTEC’s option, subject to the terms and conditions set forth below. The original purchase receipt and
product warranty information label are required to determine warranty eligibility. Eligibility is based on purchase date of original
product – not the date of replacement under warranty. The warranty is limited to repair or replacement of product only – Purchaser
pays all removal, installation, labor, shipping, and incidental charges.
For parts or troubleshooting assistance, DO NOT return product to your retail store. Contact FLOTEC Customer Service at
1-800-365-6832.
Claims made under this warranty shall be made by returning the product (except sewage pumps, see below) to the retail outlet
where it was purchased immediately after the discovery of any alleged defect. FLOTEC will subsequently take corrective action as
promptly as reasonably possible. No requests for service will be accepted if received more than 30 days after the warranty
expires.
SEWAGE PUMPS
DO NOT return a sewage pump (that has been installed) to your retail store. Contact FLOTEC Customer Service. Sewage pumps
that have seen service and been removed carry a contamination hazard with them.
If your sewage pump has failed:
• Wear rubber gloves when handling the pump;
• For warranty purposes, return the pump’s cord tag and original receipt of purchase to the retail store;
• Dispose of the pump according to local disposal ordinances.
Exceptions to the Twelve (12) Month Limited Warranty
Product Warranty Period
Drill Pump, Pitcher Pump, In-line Water Filter Cartridge 90 days
Utility Pump (Model FP0F360AC)
1/3 HP Submersible Sump Pumps, INTELLIPUMP (Model FP0S1775A)
Pool Cover Pump (Model FP0S1790PCA), Utility Pump (Model FP0S4100X) 2 Years
Condensate Pump (Model FPCP-20ULST)
Back-up Sump Pump System (Model FP2800DCC)
4" Submersible Well Pumps
1/2 HP Submersible Sump Pumps 3 Years
1/3 HP Sump Pump Models FPSC2200A-10 and FPSC2250A-10
Pre-Charge Water System Tank (FP7100 Series)
1/2 HP Sump Pump Models FPSC3200A-10 and FPSC3250A-10 5 Years
Submersible Solids Handling Pumps Models FPSE9000, E75STVT
Submersible Sump Pumps Models E50TLT, E50VLT, E75VLT, E100ELT
Floodmate®7000 (Model FP0S6000A), Pedestal Sump Pump (Model FPPSS5000)
Sewage Ejector (Model FPSE3601A), Submersible Sewage Pump (Model FPSES2700A) Lifetime
Utility Pump (Model FPSC1725X)
Submersible Sump Pump (Model FPSC4550A-10)
General Terms and Conditions
You must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty does not apply
to the following: (1) acts of God; (2) products which, in FLOTEC’s sole judgement, have been subject to negligence, abuse,
accident, misapplication, tampering, or alteration; (3) failures due to improper installation, operation, maintenance or storage;
(4) atypical or unapproved application, use or service; (5) failures caused by corrosion, rust or other foreign materials in the
system, or operation at pressures in excess of recommended maximums.
This warranty sets forth FLOTEC’s sole obligation and purchaser’s exclusive remedy for defective products.
FLOTEC SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE FOREGOING WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights and You
may also have other rights which vary from state to state.
FLOTEC • P.O. Box 342 • Delavan, WI U.S.A. 53115
Phone: [phone] • Fax: [phone]
E-Mail: [e-mail] • Web Site: http://www.flotecwater.com