Flux Basic BC 361 User manual

INSTALLATION MANUAL
COMPONENT SPEAKER
BC 361
Basic Series | Spirit Series | Maestro Series
SC 361 MC 361

You already bought one of the best German Car Hifi Component loud-
speaker System. With our special treated coated paper cone woofer, and
the light silk dome neodymium tweeter and the latest vehicle adaptive
crossover technology, you will get the maximum listening pleasure and
ultimate sound reproduction you ever hear.
WARNING
Attention
Please read all the warnings that can be found in this manual. You can
install all components in your vehicle and experience an ultimate step by
step car audio instalation procedure with proper mechanical and electri-
cal instalations.
Hearing Damage
Continuous, excessive exposure to sound pressure levels in excess of
85dB can cause a loss of hearing. FLUX Components are capable of
producing sound pressure levels greater than 85dB.
Volume and Driver Awareness
Use of sound components can impair your ability to hear necessary traf-
fic sound and may constitute a hazard while driving your vehicle. FLUX
except no liability for hearing loss boardly injury or property damage as
result of use or missused of this product.
Congratulations
Warranty Return
FLUX product guarantee only applies if the enclosed guarantee card is
retruned to us and our dealer within you buy this product, maximum 10
(ten) day of purchase.
1

FEATURES AND CONTENTS
Product Features
- Basic Series ( BC 361 )
FLUX T 160 B • 6.5” midwoofer, paper + sand coated cone
• 25mm v/c, vented steel basket
FLUX M 80 B • 3” midrange, paper + sand coated cone
• 25mm v/c, vented steel basket
• Aluminium reverse dust cap
FLUX HT 25 B • 25mm v/c with special hand coated silk dome
FLUX XB 361 • 3 way Passive Crossover for BC 361
• Adjustable tweeter & Mid Range level
• Double sided PCB with 2 OZ copper thickness to maximize signal
transfers
• Using selected silver solder to maximize contacts
• Selected component to maximize each frequency characteristic to
achieve the best tonal accuracy
- Spirit Series ( SC 361 )
FLUX T 160 S3 • 6.5” midwoofer, special coated paper cone
• 25mm v/c, vented steel basket
• Aluminium reverse dust cap
• 84 mm magnet diameter
FLUX M 80 S • 3” midrange, special coated paper cone
• 25mm v/c, vented steel basket
• Aluminium inverse dust cap
• Vented magnet
FLUX HT 25 B • 25mm v/c with special hand coated silk dome
FLUX XS 361 • 3 way passive Crossover for BC 361
• With adjustable tweeter & Mid Range level
• Double sided PCB with 2 OZ copper thickness to maximize signal
transfers
• Using selected silver solder to maximize contacts
• Selected component to maximize each frequency characteristic to
achieve the best tonal accuracy
2

- Maestro Series ( MC 361 )
FLUX T 160 M3 • 6.5” midwoofer, triple sandwich (paper+glass fiber+silk) cone
• 25mm v/c with 84mm magnet diameter
• Aluminium die cast basket, vented basket
• aluminum reverse dust cap
FLUX M 80 M • 3” midrange, triple sandwich (paper+glass fiber+silk) cone
• 25mm v/c with vented basket, neodymium magnet
• Aluminium die cast basket, screw connector
• Aluminum reverse dust cap
FLUX HT 25 M • 25mm v/c with special coated silk dome
• Duralium housing, screw connector
• vented magnet with additional rear chamber
FLUX XM 361 • 3 way passive Crossover for MC 361
• With adjustable tweeter & Mid Range level
• Double sided PCB with 2 OZ copper thickness to maximize signal
transfers
• Using selected silver solder to maximize contacts
• Selected component to maximize each frequency characteristic to
achieve the best tonal accuracy
3

Getting Started
It is recommended that your new FLUX speakers be installed by an autho-
rized FLUX Authorized Dealers. This will ensure the use of proper installa-
tion techniques and material and will save you a lot of time and efforts.
Do not use your car until all component of the loudspeaker system have
been secured to the interior framework. Failure to do so, may cause danger-
ous to a vehicle flying projectitle during a sudden stop or accident.
Do not drill or drive screws through any vehicle interior or carpeted floor
before inspecting the underside for potential punctures to control lines or
cables. Take extreme care when working near the fuel tank, gas lines brakes
or hydraulic lines and electrical wiring.
Turn off the audio system. It is also advisable to disconnect the negative
[ - ] terminal of your vehicle battery whenever performing installation
work. If the installation finished turn on the various components and slowly
advance the volume.
Remember to check and re-check all connections to insure proper installa-
tion and use.
Do not exceed the indicated maximum operational power.
Please make sure the same polarity in loudspeaker, crossover and ampli-
fier are guaranted. if speakers are wired out of phase, an unnatural sound
without bass is the result.
INSTALLATION
4

Positioning & Choosing a Location
POSITIONING
A component speaker system gives you the ability to place the woofer and
tweeter separately in your car. This can be good or bad depending on how
it’s done.
The tweeter should be placed relatively close to the woofer for best tonal
balance and most coherent imaging (the closer, the better). Any separation
greater than 60cm is likely to result in degraded sound quality. Try to alter
the pase of the tweeter if the sound that produced is not natural. For ease of
installation use original factory speaker location. Using these positions will
save considerable installation time and provide the best integration. Avoid
installing speaker behind thick stock fabric or cloth. This could especially
in the case of tweeters restrict output and reduce sound volume.
We suggest first mounting each mid/woofer and attaching the cables. Then
you can determine the optimum tweeter location by auditioning the tweeter
at several positions in your car before permanent installation.
5
Woofer
6”
Woofer
6”
Midrange
3”
Tweeter
Tweeter

CONNECTING THE COMPONENT
Connecting Up
+
+
++ + + + +
XB361
T 160 B
M 80 B
HT 25 B
Amplifier
Basic Series [ BC 361 ]
-
+
-
+
-
+
+-
6

Standard Jumper Setting
1 ( 0dB ) 2 ( -3dB ) 3 ( -6dB )
1 2 3
Midrange Level (dB)
0dB -3dB -6dB
+
+
++ + + + +
XB361
TW 0dB -3dB -6dB 0dB -3dB -6dB MID
1 2 3
0 dB
-3 dB
-6 dB
1 2 3
Tweeter Level (dB)
0dB -3dB -6dB
Basic Series [ BC 361 ]
Jumper positions are attached, you can still change it based on your
style of sound. Or it can be adapted to the conditions.
Jumper removal will affect the level of Tweeter and Woofer
7

CONNECTING THE COMPONENT
Connecting Up
+
+
++ + + + +
XS361
T 160 S3
M 80 S
HT 25 B
Amplifier
Spirit Series [ SC 361 ]
-
+
-
+
-
+
+-
8

1 2 3
0 dB
-3 dB
-6 dB
1 2 3
Tweeter Level (dB)
0dB -3dB -6dB
+
+
++ + + + +
XS361
TW 0dB -3dB -6dB 0dB -3dB -6dB MID
Standard Jumper Setting
1 ( 0dB ) 2 ( -3dB ) 3 ( -6dB )
1 2 3
Midrange Level (dB)
0dB -3dB -6dB
Spirit Series [ SC 361 ]
Jumper positions are attached, you can still change it based on your
style of sound. Or it can be adapted to the conditions.
Jumper removal will affect the level of Tweeter and Woofer
9