Flymo 1200 R User manual

Easier by Design
www.flymo.co.uk
QUICK GUIDE
Robotic
Lawnmower
120 0 R
MINIMUM
150cm
SUITABLE
FOR LAWNS
UP TO
400m2
1157876-26,QG,Flymo1200R,2016,GB.indd 25 2015-12-07 08.52

2.Charging the battery and
placement of the boundary wire
See chapter 3.3 and 3.4 in the Installation Manual
1. Place the robotic lawnmower in the charging station
to charge the battery while the boundary wire is laid.
Set the main switch to position 1.
2. Run the boundary wire ensuring it forms a loop
around the work area.
3. Make an eyelet at the point where the guide wire
will be connected later (see point 4.5).
20 cm / 8”
10 cm / 4”
0 cm / 0”
5 cm / 2”
30 cm / 12”
1. Placement of and connecting the
charging station
See chapter 3.2 in the Installation Manual
1. Place the charging station at a central position in the work area, with
a lot of open space in front of the charging station and on a relatively
horizontal surface.
2. Connect the power supply’s low voltage cable to the charging
station and the power supply.
3. Connect the power supply to a 100-240 V wall socket.
1. Main switch
2. STOP button
3. LED for function check of the
boundary and guide wires
4. Cutting height indication
5. Display
6. Keypad
Charging station
1 2 3 4 5
1 2 3
4 5 6
7 8
0
9
Start
4
5
6
1
2
3
GETTING STARTED WITH THE FLYMO 1200 R ROBOTIC LAWNMOWER
1
2
3
1157876-26,QG,Flymo1200R,2016,GB.indd 26 2015-12-07 08.52

7
4
min 2 m / 7 ft
1
1
4.Placement of and connecting the
guide wire
See chapter 3.6 in the Installation Manual
1. Run the guide wire through the slot at the bottom of the charging
station.
2. Fit the connector to the guide wire in the same way as for the
boundary wire, according to the instructions above.
3. Fasten the connector to the contact pin marked Guide on the
charging station.
4. Lay the guide wire at least 2 metres straight out from the front edge
of the charging station.
5. Run the guide wire to the point on the boundary loop the connection
will be made. Avoid laying the wire at tight angles.
6. Cut the boundary wire with a wire cutters at the centre of the eyelet
that was made in point 2.3.
7. Connect the guide wire to the boundary wire using the
accompanying couplers. Press the couplers completely together
with a pair of pliers.
1 2
4
3
3.Connecting the boundary wire
See chapter 3.5 in the Installation Manual
1. Open the connector and lay the wire ends in the recesses on each
connector.
2. Press the connectors together using a pair of pliers.
3. Cut off any surplus boundary wire. Cut 1 to 2 cm above the connectors.
4. Press the connectors onto the contact pins, marked A, on
the charging station. It is important that the right-hand wire
is connected to the right-hand contact pin, and the left-hand
wire to the left-hand pin.
5. Mark the wires with the accompanying cable markers. This makes it easier
to reconnect the wires correctly.
Power supply Low voltage cable Boundary wire
and couplers
Pegs Connectors Measurement
gauge
GETTING STARTED WITH THE FLYMO
1200 R ROBOTIC LAWNMOWER
5cm
0cm
20cm
30cm
30 cm / 12”
5
1157876-26,QG,Flymo1200R,2016,GB.indd 27 2015-12-07 08.52

Easier by Design
www.flymo.co.uk
Preston Road,
Aycliffe Business Park,
Newton Aycliffe,
County Durham,
DL5 6UP
Helpline Number: 0844 844 4558
Part Number: 115 78 76-26
Copyright @2015 Flymo S.A. All rights reserved Flymo and other product and feature names are registered
trademarks of Flymo S.A. The Husqvarna UK policy of continuous improvement and updating means that
specifications can be altered without prior notice. All measurements quoted are approximate.
6. Adjust the robotic lawnmower to suit your garden
See chapter 6.3, 6.4 and 6.5 in the Installation Manual
Here you will find some tips on important settings for your robotic lawnmower.
All settings for your robotic lawnmower are made via the menu functions.
Adjust the mower to suit the size of your lawn
The mowing results depend on mowing time. Adjust the mowing time to suit your garden using
the Timer function. If the mower cuts too often, the lawn will appear trampled down.
If the mower cuts too seldom, the lawn will not be properly mown.
Timer
You decide what times during the
day and days of the week the
mower is to work. The robotic
lawnmower mows about 33 m²
per hour and day. For example; if
your garden consists of 360 m² of
grass, the robotic lawnmower
should work on average 11 hours
per day.
1
3
Test run the mower through narrow passages
Narrow passages in the garden make it difficult for the mower to find the charging station. Use the
Calibrate guide function for the Flymo 1200R to test that the mower can travel through the
narrowest passage.
1. Place the mower in the charging station.
2. Select Calibrate guide in the robotic lawnmower’s menu and press OK. Then press the Start
button and close the cover.
3. Check that the mower follows the guide wire through the passage.
a. If the mower travels through the passage, the test is complete.
b. If the robotic lawnmower does not get through the passage: Check that the guide wire has
been laid according to the instructions in chapter 3.6 in the Installation Manual.
1 2 3 4 5
1 2 3
4 5 6
7 8
0
9
Start
1
5. Starting and stopping
See chapter 4.3 and 4.4 in the Installation Manual
Starting
1. Open the cover by pressing the STOP button.
2. Set the main switch to position 1. When you do this for the first time, a start up
sequence starts where you select a four digit PIN code among other things.
3. Press the START button.
4. Close the cover.
Stopping
Press the STOP button
1157876-26,QG,Flymo1200R,2016,GB.indd 24 2015-12-07 08.51