Flymo Chevron 34C User manual

®
IMPORTANT INFORMATION
Read before use
& retain for future reference
Chevron 34C
Chevron 34VC
Original Instructions

Carton Contents
IMPORTANT ! Please check the contents of the carton are correct BEFOREassembling your new Flymo product.
IF ANY PARTS ARE MISSING CONTACT:-
Husqvarna Australia PTY Ltd Customer Service Department direct:- Telephone : [phone]
Husqvarna New Zealand Ltd. Customer Service Department direct:- Telephone : [phone]
Safety
If not used properly this product can be dangerous! This product can cause serious injury to the operator
and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency
in using this product. The operator is responsible for following the warning and safety instructions in this
manual and on the product. Never use the mower unless the grassbox or guards provided by the manufac-
turer are in the correct position.
Explanation of Symbols on your product
Warning
Read the user instructions carefully to make
sure you understand all the controls and what
they do.
Always keep the product on the ground when
operating.Tilting or lifting the product may cause
stones to be thrown out.
Keep bystanders away. Do not operate whilst
people especially children or pets are in the
area.
Beware of sharp blades - remove plug from
mains before maintenance or if cable is dam-
aged.
Blades continue to rotate after the machine is
switched off.
Keep the cable supply away from the blade.
grassbox
upper
grassbox
lower
cable clip x 2
bolt x 2
instruction
manual
upper handle
lower handle
start/stop lever switchbox
motor cover
safety flap/vision window
VC Product only
washer x 2
lock off
button
General
1. This product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabili-
ties, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning the use of
the product by a person responsible for their safety. Children
should be supervised to ensure that they do not play with
the product. Local regulations may restrict the age of the op-
erator.
2. Never allow children or people unfamiliar with the instruc-
tions to use the machine.
3. Stop using the machine while people, especially chil-
dren, or pets are nearby.
4. Only use the product in the manner and for the func-
tions described in these instructions.
5. Never operate the product when you are tired, ill or
under the influence of alcohol, drugs or medicine.
6. The operator or user is responsible for accidents or
hazards occurring to other people or their property.
cable hook x 2
deck
height adjust lever
wing knob x 2
rating label

Electrical
1. We recommend the use of a Residual Current Circuit De-
vice (R.C.D.) with a tripping current of not more than 30mA.
Even with a R.C.D. installed 100% safety cannot be guaran-
teed and safe working practice must be followed at all times.
Check your R.C.D. every time you use it.
2. Before use, examine cable for damage or ageing. If
the cable is found to be defective, take the product to
an Authorised Service Centre and have the cable re-
placed.
3. Do not use the product if the electric cables are dam-
aged or worn
4. Immediately disconnect from the mains electricity supply if
the cable is cut, or the insulation is damaged. Do not
touch the electric cable until the electrical supply has been
disconnected. Do not repair a cut or damaged cable. Re-
place it with a new one.
5. Your extension cable must be uncoiled, coiled cables
can overheat and reduce the efficiency of your product.
6. Keep cable away from product, always work away from
the power point mowing up and down, never in circles.
7. Do not pull cable around sharp objects.
8. Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
9. Switch off, remove plug from mains and examine elec-
tric supply cable for damage or ageing before winding
cable for storage. If the supply cord is damaged, it
must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a
hazard. Use only Flymo replacement cable.
10. Always wind cable carefully, avoiding kinking.
11. Never carry the product by the cable.
12. Never pull on the cable to disconnect any of the plugs.
13. Use only on AC mains supply voltage shown on the
product rating label.
14. Flymo Products are double insulated to EN60335.
Under no circumstance should an earth be connected
to any part of the product.
Preparation
1. While using your product always wear substantial
footwear and long trousers. Do not operate the equip-
ment when barefoot or wearing open sandals.
2. Make sure the lawn is clear of sticks, stones, bones,
wire and debris; they could be thrown by the blade.
3. Before using the machine and after any impact, check
for signs of wear or damage and repair as necessary.
4. Replace worn or damaged blades together with their
fixings in sets to preserve balance.
Use
1. Use the product only in daylight or good artificial light.
2. Avoid operating your product in wet grass, where feasible.
3. Take care in wet grass, you may lose your footing.
4. On slopes, be extra careful of your footing and wear
non-slip footwear.
5. Mow across the face of slopes, never up and down.
6. Exercise extreme caution when changing direction on
slopes. Walk never run.
7. Mowing on banks and slopes can be dangerous. Do
not mow on banks or steep slopes.
8. Do not walk backwards when mowing, you could trip.
9. Never cut grass by pulling the product towards you.
10. Switch off before pushing the product over surfaces
other than grass.
11. Never operate the product with damaged guards or
without guards in place.
12. Keep hands and feet away from the cutting means at
all times and especially when switching on the motor.
13. Do not tilt product when the motor is running.
14. Do not put hands near the grass discharge chute.
15. Never pick up or carry a product when it is operating or
still connected to the mains supply.
16. Remove the plug from the mains :
- before leaving the product unattended for any period;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- if you hit an object. Do not use your product until you
are sure that the entire product is in a safe operating
condition;
- if the product starts to vibrate abnormally. Check im-
mediately. Excessive vibration can cause injury.
Maintenance and storage
1. Caution - Do not touch rotating blade.
2. Keep all nuts, bolts and screws tight to be sure the
lawnmower is in safe working condition.
3. Check the grassbox frequently for wear or deterioration.
4. Replace worn or damaged parts for safety.
5. Only use the replacement blade, and blade bolt speci-
fied for this product.
6. Be careful during adjustment of the product to prevent
entrapment of the fingers between moving blades and
fixed parts of the machine.
7. Store in a cool dry place and out of reach of children.
Do not store outdoors.
8. Allow the product to cool for at least 30 minutes before
storing.
CABLES - IMPORTANT
If you want to use an extension cable when operating your
product, only the following cable dimensions should be
used.
- 1.0 mm2: max length 40 m
- 1.5 mm2: max length 60 m
- 2.5mm2: max length 100 m
Minimum rating :
1.00mm2 size cable, 10 amps 250 volts AC.
•YOUR PRODUCT IS SUPPLIED WITH A SHORT CON-
NECTION LEAD WIRED DIRECTLY INTO THE PROD-
UCT.
1. Do not wire an extension cable directly to your product
yourself. Please contact your local Approved Service
Centre for further information.
2. Only use extension cables specifically designed for out-
door use.
FITTING A NEW MAINS PLUG
IF THE PLUG SUPPLIED IS CUT OFF IT SHOULD BE
DESTROYED. THERE IS AN ELECTRIC SHOCK
HAZARD IF A CUT OFF PLUG IS INSERTED INTO A
SOCKET. THE CABLE AND PLUG ASSEMBLY IS TO BE
REPLACED BY THE MANUFACTURERS AUTHORISED
SERVICE PROVIDER.
NO EARTH REQUIRED - Flymo products are double
insulated to EN60335/EN60745 and under no
circumstances should an earth be connected to any part of
the product.
ENSURE THE MAINS VOLTAGE SUITS YOUR PRODUCT.
IMPORTANT! The wires in the mains lead are coloured in
accordance with the following code:
BLUE - NEUTRAL : BROWN - LIVE. The wire which is
coloured BLUE must be connected to the Terminal which
is marked with the letter 'N' or coloured BLACK. The wire
which is coloured BROWN must be connected to the
Terminal which is marked with the letter 'L' or coloured
RED. It is important that the outer sheath is clamped
correctly into the 3-pin plug. If in doubt consult your local
Authorised Service provider or qualified electrician before
the machine is used.

B
Assembly of Lower Handles to Deck
1. Insert lower handles into the deck and push down (B).
2. Using a pozi drive screwdriver insert the screws into the
deck and handles and fully tighten (C).
Assembly of Upper Handles to Lower Handles.
1. Ensure the upper handle is located correctly with the
lock-off button on the switchbox uppermost.
2. Insert the nut into the handle knob.(D1)
3. Ensure the upper handle and the lower handle are
aligned correctly (D2).
4. Fit the bolts, washers and handle knobs (D2).
5. Fit the cable to the handles with the clips provided.
Make sure the cable is not trapped between the upper
and lower handles.
Attachingthe Cable Hooks (for storage of the mains cable)
1. Insert the post on the Cable Hook through the hole in the
Upper Handle (E).
2. Insert the Screw and tighten to secure (E)
Repeat for the other side.
Grassbox Assembly
1. Locate the grassbox lid onto the grassbox by aligning the clips.
Ensure all the clips are correctly located before clicking
into position. (F)
Assembly Instructions
C
D F
A
When received from the Manufacturer,
the wheels are in a raised position.
Do not switch on the product
before removing from the raised posi-
tion into position 5.
E
1
2

Grassbox
J
Fitting Fully Assembled Grassbox to Lawnmower.
1. Lift safety flap (G1)
2. Make sure the discharge chute is clean and free from
debris (G2)
3. Locate fully assembled grassbox onto 2 location
points (G3) at the rear of the deck as illustrated in
pic. H
4. Locate safety flap onto the top of the grassbox. En-
sure the grassbox is securely located.
•IMPORTANT !
AFTER FITTING ENSURE NO GAP REMAINS BE-
TWEEN THE SAFETY FLAP AND THE GRASSBOX.
• Removal is the reverse procedure.
• For larger areas of grass where grass collection is
not required you can use your lawnmower without
the grassbox. Ensure the Safety Flap is fully closed.
The design of the safety flap permits the cut grass to
be discharged downward behind the machine.
Grassbox Full Window (34VC only)
•As the grassbox fills up, grass will be visible through
the window (J).
• When the window/grassbox is full it is time to empty
the grassbox.
grassbox
empty
grassbox
full
G
1
2
3
H
Cutting Height Adjustment
Cutting Height Adjustment
• Height of cut is adjusted by raising or lowering the
wheels using the height adjustment lever (K)
• There are five heights of cut on this product. (20 - 60
mm)
• NOTE
A medium height of cut is recommended for most
lawns.
The quality of your lawn will suffer and collection will be
poor if you cut too low.
K

P
Starting and Stopping
To Start your Lawnmower
To ensure you have a secure connection between the
lawnmower and the extension cable we strongly recom-
mend you use the following method of attaching the
cable:
1. Plug the short connection lead into the socket of the
extension cable. (L1).
2. Form a loop in the end of the extension cable near to
the socket and secure this in the strain relief feature at
the top of the switchbox (L2). This will cause the
socket to hang in a downward direction. (L3)
3. Connect plug to mains and switch on.
4. Tilt the handle downwards to slightly raise the front of
the lawnmower and to reduce the risk of lawn damage
whilst starting.
The switchbox is provided with a lock-off button (M1) to
prevent accidental starting.
5. Press and hold the lock-off button (M1) on the switch-
box, then squeeze one of the Start/Stop levers towards
the upper handle (N).
6. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button (P).
7. Lower the lawnmower to its proper operating position
and commence mowing.
•NOTE - There are two start/stop levers fitted. Either
one can be used for starting the lawnmower.
• IMPORTANT - Do not use the start/stop levers intermit-
tently
To Stop your Lawnmower
1. Release the pressure on the Start/Stop lever.
M N
1
L1 L2
L3
How to Mow
1. Start mowing the edge of the lawn nearest to the power point so the cable is laid out on the lawn you have already cut.
2. Mow twice a week during the growing season, your lawn will suffer if more than a third of its length is cut at one time
and this may also result in poor collection.
Do Not Overload Your Mower
Mowing long thick grass may cause the motor speed to drop, you will hear a change in the motor sound. If the motor
speed drops you may overload your lawnmower which may cause damage. When mowing in long thick grass a first
cut with the cutting height set higher will help reduce the load. See Cutting Height Adjustment.

Q
blade
blade bolt
washer
Removing and Fitting the Blade
Switch off, wait until the blade has stopped rotating and
disconnect from the mains electricity supply BEFORE at-
tempting to remove or refit the blade.
Always handle the blade with care - sharp edges could
cause injury. USE GLOVES.
Removing the Blade
1. T
o remove the blade bolt, hold the blade firmly with a
gloved hand and with a spanner, loosen the blade bolt
by turning it anti-clockwise (Q).
2. Remove the blade bolt, washer and blade.(Q)
3. Inspect for damage and clean as necessary.
4. In the event of a blade becoming difficult to remove, insert a
screwdriver (R1) into the hole (R2) to lock the drive, then use
a spanner (13mm A/F) to loosen the blade bolt by turning
the spanner anti-clockwise. Ensure the screwdriver is re-
moved before atempting to turn on the machine.
Renew your metal blade after 50 hours mowing or 2 years
whichever is the sooner - regardless of condition. If the
blade is cracked or damaged replace it with a new one.
Fitting the Blade
1. Fit the blade to the shaft with the sharp edges of the
blade pointing away from the shaft and you are able to
read the text on the blade ‘This side to grass’
2. Re-assemble blade bolt through the washer and the blade.
3. Hold the blade firmly with a gloved hand and tighten the
blade bolt firmly with a spanner . Do not over tighten.
R
1
2
Caring for your Lawnmower
Cleaning
• USE GLOVES
• IMPORTANT:- It is very important that you keep your
lawnmower clean. Grass clippings left in any of the air
intakes or under the deck could become a potential fire hazard.
1. Remove grass from under the deck with brush. (S1)
2. Using a soft brush - remove grass clippings from all air
intakes (S2), the discharge chute (S3) and the grass
box (S4).
3. Using a soft brush, remove grass clippings from the vi-
sion window (S5).
4. Wipe over the surface of your lawnmower with a dry
cloth (S6).
•IMPORTANT:- Never use water for cleaning your lawn-
mower. Do not clean with chemicals, including petrol, or
solvents - some can destroy critical plastic parts.
Storing your Cable
• Your electric cable can be wrapped around the hooks to
enable tidy and safe storage (T1).
Storing your Lawnmower:
• Loosen the wing knobs to enable the handles to be
folded over the product (T2).
• Store in a dry place where your lawnmower is pro-
tected from damage
At the End of the Mowing Season
1. Replace blade, bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Make sure that the electric cable is stored correctly to
prevent damage.
S1 S2
S3 S4
S5 S6
T2
T1

Fault Finding Hints
Fails to Operate
1. Is the correct Starting procedure being followed? See ‘To
Start your Lawnmower’
2. Is the Power Turned On?
3. Check the fuse in the plug, if blown replace.
4. Fuse continues to blow?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Poor Grass Collection
1. Disconnect from the mains electricity supply.
2. Clean the outside of the air intakes, the discharge chute
and the underside of the deck.
3. Raise to a higher height of cut. See Cutting Height Adjust-
ment.
4. If poor collection persists.
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Excessive Vibration
1. Disconnect from the mains electricity supply.
2. Check that the blade is fitted correctly?
3. If the blade is damaged or worn, replace it with a new one.
4. If vibration persists?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Lawnmower becomes heavy to push
1. Disconnect from the mains electricity supply.
2. In long grass or uneven ground, the height of cut should be
raised to a higher position. See Cutting Height Adjust-
ment.
3. Check that the wheels and rollers can rotate freely.
4. If problem persists?
Immediately disconnect from the mains electricity supply
and consult your local approved Service Centre.
Service Recommendations
1. We strongly recommend that your product is serviced at
least every twelve months, more often in a professional ap-
plication.
2. Always use genuine Spare Parts.
3. Prepacked spares are available from most Husqvarna
Australia PTY/Husqvarna New Zealand Ltd. stockists.
4. Your product is uniquely identified by a silver and black
product rating label
5. If you have a problem with your machine contact your local
Approved Service Centre ensuring you have full details of
your product as described on the product rating label.
6. Should it be necessary for work to be carried out by your
Service Centre, it is important to take your complete ma-
chine including cable and any extension cables used.
A network of specialist dealers can be found in your local Yel-
low Pages.
To obtain service on your product simply telephone or visit
your local Service Centre.
Should you require service under the terms of our guarantee
the Service Centre will require proof of purchase.
All of the centres listed stock genuine Spare Parts.
NOTE: Our Service Repairers act on their own behalf and are
not empowered to commit or legally bind Husqvarna Australia
PTY/Husqvarna New Zealand Ltd. in any manner whatsoever.
If any part is found to be defective due to faulty manufacture
within the guarantee period, Husqvarna Australia PTY/Husq-
varna New Zealand Ltd., through its Authorised Service Re-
pairers will effect the repair or replacement to the customer
free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty ad-
justment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken
apart or tampered with by any person not authorised by
Husqvarna Australia PTY/Husqvarna New Zealand Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way diminishes
the customers statutory rights.
Failures due to the following are not covered, therefore it is
important that you read the instructions contained in this Op-
erator's Manual and understand how to operate and maintain
your machine:
Failures not covered by guarantee
* Replacing worn or damaged blades.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accor-
dance with the instructions and recommendations con-
tained in this Operator's Manual.
* Machines used for hire are not covered by this guaran-
tee.
* The following items listed are considered as wearing
parts and their life is dependent on regular maintenance
and are, therefore not normally subject to a valid war-
ranty claim: Blades, Electric Mains cable
*Caution!
Husqvarna Australia PTY/Husqvarna New Zealand Ltd..
does not accept liability under the warranty for defects
caused in whole or part, directly or indirectly by the fitting
of replacement parts or additional parts that are not ei-
ther manufactured or approved by Husqvarna Australia
PTY/Husqvarna New Zealand Ltd., or by the machine
having been modified in any way.
Guarantee & Guarantee Policy
Environmental Information
• Awareness of the environment must be considered
when disposing of ‘end-of-life’ product.
• If necessary, contact your local authority for disposal
information.
The symbol on the product or on its packaging indi-
cates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic
equipment.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the envi-
ronment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this prod-
uct, please contact your local council office, your house-
hold waste disposal service or the shop where you
purchased the product.

5790405-01
Declaration of Conformity
Husqvarna AB, 561 82, Huskvarna, Sweden
Declare under our sole responsibility that the product(s);
Category........................................ Electric Rotary Lawnmower
Model(s).........................................C340C, C340VC
Identification of Series................... See Product Rating Label
Year of Construction...................... See Product Rating Label
Complies with following standards:
IEC60335-1, EN60335-2-77, EN50366, EN55014-1, EN61000-3-2, EN61000-3-3
The maximum A weighted sound pressure level LpA at the operator’s position, recorded on a sample of the above prod-
uct(s) corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 5349 on a sample of the above
product(s) corresponds to the Value ahgiven in the table.
Newton Aycliffe, 02/08/11
M. Bowden,
Global R & D Director - Walk behind
Husqvarna UK Ltd.
Keeper of technical documentation
Type
Width of Cut (cm)
Speed of Rotation of Cutting Device (RPM)
Power (kW)
Level LpA(dB(A))
Uncertainty KpA (dB(A))
Value
ah (m/s2)
Weight (Kg)
Husqvarna AB
561 82
Huskvarna
Sweden
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2010 Flymo S.A. All rights reserved. Flymo® and other product and feature names are registered or un-
registered trademarks of Flymo S.A.
C340C
34
3700
1.4
78.2
2.5
1.79
10.8
Replacement Parts
Blade
Reference no.: FLY 066
Part no.: 577366490
C340VC
34
3700
1.4
78.2
2.5
1.79
10.8