FLYTEAM EPP Trust Instruction Manual

radio controlled plane for beginners
Wingspan
Lenght
Weight
Power
Propeller
Battery
Controls
mm
mm
g
PJS - 550, (900)
9/4,7;11/4,7
3x LiPol 2000 mAh
30A
Ailerons, rudder, elevator, ESC
1000
840
640
Specifications
EPP
Building instructions
Trust
TRUST
Lazertoyz.com
440-840-9625

74
Page 2
72+73
RC equipment
REX
RE CE IV ER
SINGLE CONVERSION
4 micro
FM
4 CHANNEL
4/B
3
2
1
91 93
94
Power
Engine
propeller
3 ks
ESC
95
Battery
Bowden 1 pc
13
18
19
42
20
23
21
22
16
24
wheels landing gear
horns 4 pcs.
front landing
gear
motor mount
variable clamp of pushrods 4 pcs
rubber loops 2 pcs
2
Kit content:
whell ocking
Ř 2,5 mm 1 pcs
3 pcs 15
12
1 Fuselage
2 wing left/right
2
3 Rear cover
4 Canopy
5fin
6 rudder
7 reinforcement
of fin
8 stabilizer
9 elevator
10 reinforcement of stabilizer
11 reinforcement of wing
landing gear holder 2 pcs
Upper cowl
(cover)
Hinges
5 pcs
nuts 4ps screw 2ks

Join and glue the left panel with the right one use PU glue( ).
Glue wood reinforcement (beam) to the left panel. Use PU glue.
11
Glue the whole wing to the fuselage (use Pu glue).
Check the correct position.
8
Glue the reinforcement [part 10] to the stabilizer 8.
Join elevator and stabilizer with a hinges 42.
Glue stabilizer to the fuselage with PU glue.
56
7
Glue the reinforcement part 7 the fin. Join the fin and the rudder with hinges 42.
Fit and glue the complete fin into the fuselage secure their correct position.
( ) to
(use the PU glue). Check and
90
Page 3
9
10
23
42
Det.
desk
30 mm 30 mm

RX
Glue horns 23 to the rudder and the elevator.
Mount the servos to the fuselage (
).
cut appropriate
holes on the opposite sides of the fuselage
Cut slots for outer pushrod tubes.
A
15 23
B
Glue the motor mount 22 to the fuselage (use PU)
Install ailerons servo. The ailerons servo
must tightly fit in the hole without unnecessary
clearance. Make slots ducts for all servo wires.
Glue horns to the ailerons. Then install pushrods
/
(similar as with the elevator/rudder).
18
19
120 mm
80 mm
Assembly the front
parts 18 and 20
(parts
19 and 21) and main undercarrige
( ).
Cut slots for the front
andmain undercarriage use
soldering iron or a knife
(
).
21
22
3
23
15
24
4
Cut the upper cover (cowl)
(use PU glue)
according to the picture.
The middle part is removable and enables easy access
to battery which located inside. Glue the remaing
parts to the fuselage .
The pushrod tubes should remain straight - so the slots must be
cut properly. Bend one end of the pushrod to "Z" shape. Mount the
pushrod through tube to the rudder and servo horns, adjust the
proper length of pushrod to bring the control surfaces into the neutral
position and bend the second end of the pushrod. Glue the pushrods
to the fuselage.
Cut the cockpit cover 4 and glue it to fuselage.
23 23
15
Page 4
18
Prepare front and rear chassis (like on picture).
The wheels have to rotate easily
13

RX
BATT
70 - 80 mm
Wiring diagram example(an )
91 94
93
95
72
73
80 - 100 % W
4/B
3
2
1
+
+
-
-
-
-
+
+
A
C
C
U
M
O
T
O
R
74
Make hole the receiver in the fuselage use soldering iron and/or a knife
the model with the battery - cut the hole so that the balance point
center of gravity s according to the picture.
( ).
Balance
( ) position i
Page 5