FLYTEAM Miracle EPP User manual

Miracle
EPP
Specifications:
Radio controlled aerobatic model
Guide for assembling and flying
Lazertoyz.com
440-840-9625
Lazertoyz.com
Wingspan
Length
Weight
Power
ESC
Prop
Battery
900=36"
920
290
MM
MM
G
GT2215/09 1180KV
Lazertoyz 30 amp
9 - 10 in
1300 mah 3s 11.1v

wing panels
(left/right)
Bowden
Canopy
instructions
rudder
1pcs
elevator (left/right)
front cover
co errear v
fuselage
lower cover
2
3
1
4
11
12
16
18
20
19
22
23
Vheels
steel wire
of wheels
motor mount
tai skid
gear holder
horns
wood
screwt 2,2x9,5
elevator link
4 ps
3ps
KIT CONTENTS:
74
Page 3
72+73
RC equipment
Required accessories
REX
RE CE IV ER
SINGLE CONVERSION
4 micro
FM
4 CHANNEL
4/B
3
2
1
91
93
94
Power
Brushless motor
PJS 550 R
3 pc
ESC 18 A
95
Battery
3 cl. LiPol 1200
MIZAR
MIZAR
2 ps
5
6
8
10
13
14
proppeler
27
snaps for regulacion of pushrods
25
rubber loop
nut screw 2 ps4 ps

Battery Elevator servo - left side
Rudder servo - right side
Ailerons servo
Ailerons servo
Make holes for battery, receiver and servos in the fuselage (use soldering iron and/or knife) The
eguipment must tightly fit in the holes without unnecessary clearance. Make slots/ducts for servo
wires.
Gear holder
desk wing upside
Glue the left and right wing pannels together with PU. (no dihedral, upper side down to desk)
1
8
8
8
16
Glue elevator link 16 with CyA to the elevator on the upside.
Mount the wing to the fuselage and glue with PU.
THE UPPER VIEW:
upside elevator
5
Glue the left and right elevator panels with PU
!!! upside elevator must be level surface!!!
Page 4
!!! upside wings must be level surface!!!
!!! Don´t glue lower cover 4 now!!!
Glue the elevator to the fuselage with PU.
Receiver

19
Assembly the steel wire and wheels
(see picture for detail C)
6
Glue the rudder to the fuselage with PU. The rudder
must be verticaly.
Glue the to the fuselage with PU.rear cover
Cut the front cover to the three parts and their outside
glue to the fuselage with PU. To the front part cut slot for
engine.
Glue the horns 18 to the rudder and elevator.
Insert servos in holes. Cut slots for pushrods
tubes. The pushrod tubes should remain straight
so the slots must be cut properly. Bend one end
of the pushrod to "Z" shape.
Mount the pushrods trought tubes to the rudder
and servo horns, adjust the proper lenght of
pushrod to bring the control surfaces into the
neutral position and screw up of the snap 27 the second end
of the pushrod. Glue the pushrod to the fuselage.
10 18
B
Glue tail skid 22 with CA to the fuselage.
Cut canopy 11 of the stamping and glue to the fuselage
with CyA. Glue motor mount 19 to the fuselage with PU
Mount ailerons servo to the fuselage. Glue horns 18 to the ailerons. Mount pushrod tubes. (follow
instruction 4 and 5 obove)
The lower part view on the ailerons servo without the lower cover.
Page 5
c
10
27
A
2
3
23
11
6
RX
REG BAT
A
B
4
22
B
B
19
18 18
10

Wiring diagram (an example)
91 94
93
95
72
73
80 - 100 % W
Start at full throttle
4/ B
3
2
1
+
+
-
-
-
-
+
+
A
C
C
U
M
O
T
O
R
74
Mount the engine to the motor mount 19. Try a center of gravidity of model and fixing battery
to the fuselage with velcro or rubber loop.
Other planes of our EPP series are on the webside www.boruvka.info
Page 6
Fix the rmovable with
a rubber loop
BAT
Completion:
80-90
24
25
10-15
10-15