FMI DVC36B Quick start guide

For more information, visit www.fmiproducts.com
Installation and service must be performed by a quali-

    -
-

      -


-






      

DIRECT-VENT CHASSIS
OWNER’S INSTALLATION INSTRUCTIONS
MODELS (V)DVC36(B)(H) AND (V)DVC42(B)(H)
FOR USE WITH DVM SERIES BURNER MODULES

PFS
®
US

www.fmiproducts.com 118197-01D2

    



-

-
   





   -


    
   
   

    

1. Neverinstallthereplace
• inarecreationalvehicle
• inwindyordraftyareaswherecurtainsor
othercombustible(ammable)objectscan
makecontactwiththereplacefront
• inhightrafcareas
2. Turnapplianceoffandletcoolbeforeservic-
ing,installingorrepairing.Onlyaqualied
servicepersonshouldinstall,serviceorrepair
thisreplace.Havereplaceinspectedannu-
allybyaqualiedserviceperson.
SAFETy INFORMATION
TABLE OF CONTENTS
Safety Information ............................................... 2
Local Codes......................................................... 3
Product Identication........................................... 3
Product Features................................................. 3
Pre-Installation Preparation................................. 4
Location of Termination Cap................................ 6
Venting Installation Instructions ........................... 7
Replacement Parts............................................ 16
Technical Service............................................... 17
Accessories ....................................................... 17
Illustrated Parts Breakdown and Parts List........ 18
Warranty Information ...........................Back Cover
   
manual carefully and completely


     
    
   
   

    

    
-



-







    




www.fmiproducts.com
118197-01D 3
SAFETy INFORMATION
Continued
3. Youmustkeepcontrolcompartments,burn-
ersandcirculatingairpassagesclean.More
frequentcleaningmaybeneededduetoex-
cessivelintanddustfromcarpeting,bedding
material,etc.Turnoffthegasvalveandpilot
lightbeforecleaningreplace.
4. Haveventingsystem inspected annually by
a qualied service person. If needed, have
ventingsystemcleanedorrepaired.
5. Donotuseanysolidfuels(wood,coal,paper,
cardboard,etc.)inthisreplace.Useonlythe
gastypeindicatedonreplacenameplate.
6. Thisappliance,wheninstalled,mustbeelectri-
callygroundedinaccordancewithlocalcodes
or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70.
7. Donotusereplaceifanyparthasbeenex-
posedtoorunderwater.Immediatelycalla
qualiedservicepersontoarrangeforreplace-
mentoftheunit.
8. Donotoperatereplaceifanylogisbroken.
9. Do not operate fireplace with glass door
removed,crackedorbroken.
10. Provide adequate clearances around air
openings.
LOCAL CODES
Installandusereplacewithcare.Followalllocal
codes.Intheabsencetolocalcodes,usethecurrent
National Fuel Gas Code ANSI Z223.1/NFPA 54*.
*Availablefrom:
AmericanNationalStandardsInstitute,Inc.
1430Broadway
NewYork,NY10018
NationalFireProtectionAssociation,Inc.
BatterymarchPark
Quincy,MA02269
Figure 1 - Direct-Vent Fireplace
Glass Door
Assembly
Switch Bracket for Optional
Remote and Blower
Upper Louver
Panel
Lower Louver
Panel
Flue Collar
Nailing
Flange
PRODUCT FEATURES
Theseareafewfactsthatcanhelpyouunderstand
andenjoyyourdirect-ventreplace:
• Theventingsystemmayberoutedtotheout-
sideofyourhomeinseveralways.Itmayvent
throughtheroof(vertical)oritmayventtoan
outside/exterior wall (horizontal). The vent
pipeinstallationisveryimportanttoallowfor
properoperation.Youmustfollowtheventing
instructionsverycarefullyforeitherverticalor
horizontalapplications.
• Thisreplacemaybeinstalledinanyroomof
yourhouseprovidedalllocal codes andthese
installationinstructionsarefollowed.
• Thisreplacerequiresawallswitch,hand-held
remoteorwallthermostat(millivolt)foropera-
tion(seeAccessories,page42).
• The use of a blower requires electricity if
installed.Ifyouplantoinstalltheblowerata
laterdate,outletatbottomofreplacemustbe
wiredduringframing.
• Yourdirect-ventgasreplacesystem(replace
andventing)isabalancedandsealedgasop-
erating unit. It requires approximately 10-20
minutes of operating time before the ame
patternstabilizes.
PRODUCT
IDENTIFICATION

www.fmiproducts.com 118197-01D4
D
RW
FW
Figure 2 - Common Fireplace Locations
Flush with a wall
Through exterior wall
enclosed in a chase
Corner
installation
Figure 3 - Fireplace Bottom Dimensions
29" (36")
36 1/4" (42")
41" (36")
48" (42")
teriornish.
• There must not be any obstruction such as
bushes, garden sheds, fences, decks or util-
itybuildingswithin24"fromthefrontofthe
terminationcap.
• Donotlocateterminationcapwhereexcessive
snoworicebuildup may occur. Besureto
clearventterminationareaaftersnowfallsto
preventaccidentalblockageofventingsystem.
Whenusingsnowblowers,donotdirectsnow
towardsventterminationarea.
PRE-INSTALLATION
PREPARATION


Determinethesafestandmostefcientlocation
for your FMI PRODUCTS, LLC direct-vent
replace. Make sure that rafters and wall studs
arenotinthewayoftheventingsystem.Choose
alocation where the heat outputis not affected
by drafts, air conditioning ducts, windows or
doors.Figure2showssomecommonlocations.
Beawareofallrestrictionsandprecautionsbefore
decidingtheexactlocationforyourreplaceand
terminationcap.
When deciding the location of your replace,
followtheserules:
• Donotconnectthisreplaceventingtoachim-
neyueservingaseparatesolid-fuelburning
replaceorappliance.
• Due to high temperatures, do not locate this
replaceinhightrafc areas, windy or drafty
areasornearfurnitureordraperies.
• Properclearancesmustbemaintained.
• Ifyour replaceistobeinstalleddirectlyon
carpeting,vinyltileoranycombustiblemate-
rialotherthanwood,itmustbeinstalledona
metalorwoodpanelextendingthefullwidth
anddepthofthereplace.SeeFigure3.
• Yourreplaceisdesignedtobeusedin zero
clearanceinstallations.Wallorframingmaterial
canbeplaceddirectlyagainstanyexteriorsur-
faceontheback,sidesortopofyourreplace,
except where standoff spacers are integrally
attached.Ifstandoffspacersareattachedtoyour
replace,thesespacerscanbeplaceddirectly
againstwallorframingmaterial.Seeframing
detailsonpage5.
• Ifyouplanoninstallingatelevisionorenter-
tainmentcenterrecessedaboveyourreplace,it
isrecommendedthatyoumaintainaminimum
18"abovetopoflouveropening.
• Whenlocatingterminationcap,itisimportant
toobservetheminimumclearancesshownin
Figure7,page8.
• If recessing into a wall, you can avoid extra
framingby positioningyourreplaceagainst
analreadyexistingframingmember.
• Do not recess termination cap into a wall or
siding.
• Youmaypainttheterminationcapwith450ºF
heat-resistantpainttocoordinatewiththeex-

Minimum clearances to combustibles for the re-
placeareasfollows:
*Backandsides 0"
Perpendicularwalls 6"
Floor 0"
Ceilingtolouveropening 42"
Front 36"
TopofStandoffs 0"
Vent (Seeventinginstructionsfor
specicventingclearances.)
Combustible material with a maximum thick-
ness of 5/8" may be ush with the top front of
replace.
*For back and sides of replace,do not pack
with insulation or other materials. Zero inch
clearancetocombustiblematerialsareforfram-
ingpurposeonly.
21 1/8" (36")
23 1/4" (42")

www.fmiproducts.com
118197-01D 5
PRE-INSTALLATION
PREPARATION
Continued
A
B
E
F
G
H
DC
Nailing Tabs
Figure 4 - Framing Clearances for
Installation Against an Exterior Wall
361/8" (36")
401/8" (42")
411/4" (36")
481/4" (42")
21" Hor. Vent
241/2" Vert. Vent
Figure 5 - Framing Clearances for Corner
Installation
41"
411/4"
353/4"
15" 49 5/8"
133/4"
681/2"
103/8"
Nailing
Tabs
C
B
A
DE
FG
T o p of Louver
Opening
3
2
1
4
5
6
7
Wa ll
Ref. Mantel Depth Ref.
Mantel from
Top of Louver
Opening
1 14" A 16"
2 12" B 14"
3 10" C 12"
4 8" D 10"
5 6" E 8"
6 4" F 6"
7 2" G 4"
Figure 6 - Clearances for Combustible
Mantels
23" Hor. Vent
26 1/2" Vert. Vent
36"
42"
A
B
E
F
G
H
DC
Nailing Tabs
48"
481/4"
415/8"
215/8"58 1/2"
163/4"
811/2"
131/2"
Nailing
Tabs
36" Models
42" Models
    -
tended for use as supplemental






    
-




Figure4showstypicalframingofthisreplace.
Figure5showsframingforcornerinstallation.All
minimumclearancesmustbemet.
For available accessories for this replace, see
Accessoriesonpage17.Ifyouareusingasepa-
ratecombustiblemantelpiece,refertoFigure6
for proper installation height. You can install
noncombustiblemantelsatanyheightabovethe
replace.
Note:Noncombustiblemantelsmaydiscolor!

www.fmiproducts.com 118197-01D6
Figure 7 - Minimum Clearances for Termination Cap
LOCATION OF TERMINATION CAP
Fixed
Closed OpenableFixed
Closed
V
V
V
V
VV
V
V
X
X
VX
G
G
J
F
B
B
K
N
H
I
A
N
E
L
D
B
M
A
C
B
V
V
A
G
G
B
TERMINATION CAP AIR SUPPLY INLET GAS METERRESTRICTED AREA
(TERMINATION PROHIBITED)
A = clearance above grade, veranda, porch, deck, or
balcony [*12" (30.5 cm) minimum]
B = clearance to window or door that may be opened
[6" (15 cm) min. for 10,000 Btu or less; 9" (23 cm) in US
if between 10,000 and 50,000, 12" (30 cm) in Canada
if between 10,000 and 100,000; 12" (30 cm) in US if
greater than 50,000, 36" (91 cm) in Canada if greater
than 100,000]
C = clearance to permanently closed window
[minimum 12" (30.5 cm) recommended to prevent
condensation on window]
D = vertical clearance to ventilated soffit located above the
terminal within a horizontal distance of 24" (61 cm) from
the center-line of the terminal [18" (45.7 cm) minimum]
E = clearance to unventilated soffit [12" (30.5 cm) minimum]
F = clearance to outside corner (see below)
G = clearance to inside corner (see below)
H = *not to be installed above a meter/regulator assembly
within 36" (91.4 cm) horizontally from the center line
of the regulator
I = clearance to service regulator vent outlet [*72" (182.9 cm)
minimum]
J = clearance to non-mechanical air supply inlet to building
or the combustion air inlet to any other fireplace
[6" (15 cm) min. for 10,000 Btu or less; 9" (23 cm) in US
if between 10,000 and 50,000, 12" (30 cm) in Canada
if between 10,000 and 100,000; 12" (30 cm) in US if
greater than 50,000, 36" (91 cm) in Canada if greater
than 100,000]
K = clearance to a mechanical air supply inlet [*In Canada,
6 ft. (1.83m) minimum; In US 3 ft. (91 cm) above if within
10 ft. (3 m) horizontally]
L = † clearance above paved side-walk or a paved driveway
located on public property [*84" (213.3 cm) minimum]
M = clearance under veranda, porch, deck
[*12" (30.5 cm) minimum ‡]
N = clearance above a roof shall extend a minimum of
24" (61 cm) above the highest point when it passes
through the roof surface and any other obstruction within
a horizontal distance of 18" (45.7 cm)
† vent shall not terminate directly above a side-walk or paved driveway which is located between two
single family dwellings and serves both dwellings*
‡ only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*
* as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.
Note: Local codes or regulations may require different clearances
A = 6" (15.2 cm)
Inside Corner
V
B
E
V
B = 6" (15.2 cm)
C = Maximum depth of 48" (121.9 cm)
for recessed location
D = Minimum width for back wall of
recessed location -
Combustible - 38" (965 mm)
Noncombustible - 24" (61 cm)
E = Clearance from corner in
recessed location-
Combustible - 6" (15.2 cm)
Noncombustible - 2" (5.1 cm)
Outside Corner Recessed Location
G
H
G = 12" (30.5 cm) minimum clearance
Balcony with No Side Wall
V
J
Combustible &
Noncombustible
H = 24" (61 cm)
J = 20" (50.8 cm)
Balcony with Perpendicular Side Wall
C
D
C
Termination Clearances for Buildings with Combustible and Noncombustible Exteriors
Openable

www.fmiproducts.com
118197-01D 7
VENTINg INSTALLATION
INSTRUCTIONS
   -
tions completely before at-

These models are tested and approved for use
with FMI PRODUCTS, LLC (direct-vent) pipe
componentsandterminations.
Theventingsystemmustterminateontheoutsideof
thestructureandcannotbeattachedtoachimney
oruesystemservingaseparatesolidfuelorgas
burning appliance. A direct-vent appliance must
haveitsownventingsystem.DONOTcommon
ventthisappliance.
These models are approved to be vented either
horizontallythroughanoutsidewallorvertically
througharooforchaseenclosureusingthefol-
lowingguidelines:
• Whenventingsystemterminateshorizontally
onanoutsidewall,youmayinstallastandoff
iftheterminationcapistobeinstalleddirectly
onacombustiblenishsuchasvinyl,wood,
stucco,etc.
• Never run the vent downward as this may
cause excessive temperatures which could
causeare.
• Ventpipeairspaceclearancestocombustibles
are 1" on all sides except on the horizontal
sections, which requires 2" clearance from
thetopofthepipe.Wheretheterminationcap
penetrates a combustible wall, 1" air space
clearanceisrequired.
• Snorkel terminations are required when
minimumclearancetogradecannotbemet(see
Figure16onpage11).
• Havereplaceandselectedventcomponentson
handtohelpdeterminetheexactmeasurements
whenelbowingoroffsetting.Alwaysusewall
restopswhenpenetratingwallsandrestops
whenpenetratingceilingsoratticspaces.
• Ifusingaventingcongurationofonlyhori-
zontalventingwithnoverticalrun,a1/4"rise
forevery12"ofruntowardtheterminationis
required.
• Forinstallationofreplaceatelevationsof4000
feetorgreater,payspecialattentiontoventing
requirementrecommendations.
WARNING: Read all instruc-

  



-


  
removable for vent inspection


• Wearglovesandsafetyglassesforprotection
• Use extreme caution when using ladders or
whenonrooftops
• Beawareofelectricalwiringlocationsinwalls
andceilings
Thefollowingactionswillvoidthewarrantyon
yourventingsystem:
• Installationofanydamagedventingcomponent
• Unauthorizedmodicationoftheventingsys-
tem(Donotcutoralterventcomponents)
• Installationofanycomponentpartnotmanufac-
turedorapprovedbyFMIPRODUCTS,LLC
• Installation other than as instructed by these
instructions

andventassemblymustbevented




   


WARNING: Vent pipe air
spaceclearancestocombustibles







www.fmiproducts.com 118197-01D8

There are two basic types of direct-vent in-
stallation:
• HorizontalTermination
• VerticalTermination

IMPORTANT: Horizontal square terminations
requireonlyinnerportionofwallrestop.Hori-
zontalinstallationsusingroundterminationrequire
exterior portion of wall restop (see Figure 14,
page10.
1. Setthereplaceinitsdesiredlocationanddeter-
minetherouteyourhorizontalventingwilltake.
Donotsecurethereplaceuntilallventinghas
beeninstalled.Someinstallationsrequiresliding
thereplaceinandoutofpositiontomakenal
ventingconnections.Figures14through18on
pages10through12showdifferentcongura-
tionsforventingwithhorizontalterminationthat
willhelpyoudecidewhichapplicationbestsuits
yourinstallation.Checktoseeifwallstudsor
roofraftersareinthepathofyourdesiredvent-
ingroute.Iftheyare,youmaywanttoadjustthe
locationofthereplace.
2. Directventpipesectionsandcomponentsare
designedwithspecialtwist-lockconnections.
Thefemaleendsofthe
pipeshave lockinglugs(indentations).These
lugswillslidestraightintomatchingslotson
themaleendsofadjacentpipes.Pushpipesec-
tionstogetherandtwistonesectionclockwise
approximatelyone-quarterturnuntilthesections
arefullylocked(seeFigure8).Note:Horizontal
runsofventmustbesupportedeverythreefeet.
Usewallstrapsforthispurpose.
3. Usea45° elbow toconnectventing system
toreplaceuecollar.Theelbowisdesigned
to be twist-locked onto the flue collar as
described in step 2. IMPORTANT: Do not
attempttoalterthecongurationoftheelbow
bycutting,twisting,bending,etc.
4. Assemblethedesiredcombinationofpipeand
elbowstothereplaceuecollar.Ifthereare
longportionsofventingrun,pre-assembled
pipesectionsmaybeinstalledassubassem-
bliesforconvenience.
VENTINg INSTALLATION
INSTRUCTIONS
Continued
Figure 8 - Vent Pipe Connections
Female
Locking
Lugs
Male
Slots
(Framing
Detail)
11
1
/
2
"
11
1
/
2
" Inside Framing
11
1
/
2
"
8
1
/
2
"
Vent
O
pening
Combustible Wall
Vent Opening
Noncombustible Wall
Figure 9 - Vent Opening Requirements
Center of
Hole
5. Carefullydeterminethelocationwherethevent
pipeassemblywillpenetratetheoutsidewall.
Thecenteroftheholeshouldlineupwiththe
center-lineofthehorizontalventpipe.Markthe
wallfora111/2"x111/2"squarehole.Cutand
framethesquareholeintheexteriorwallwhere
theventwillbeterminated.Ifthewallbeing
penetrated is constructed of noncombustible
material,suchasmasonryblockorconcrete,
a 8 1/2"holewithzeroclearanceisacceptable
(seeFigure9).

www.fmiproducts.com
118197-01D 9
VENTINg INSTALLATION
INSTRUCTIONS
Continued
WARNING: Do not recess


6. Positionthe
horizontalventcapinthecenterofthe81/2"
roundholeandattachtotheexteriorwallwith
fourwoodscrewsprovided.Beforeattaching
theventcapto exterior wall, run a bead of
non-hardeningmastic(pliablesealant)around
theoutsideedgestomakeasealbetweenitand
theoutsidewall.Note:Thefourwoodscrews
providedshouldbereplacedwithappropriate
fastenersforstucco,brick,concreteorother
typesofsidings.
Forvinylsiding,
stuccoorwoodexteriors,asidingstandoffmay
beinstalledbetweentheventcapandexterior
wall. The siding standoff prevents excessive
heat from damaging the siding materials.
Sidingmaterialmustbecuttoaccommodate
standoff.Bolttheventcaptothestandoff.Ap-
plynon-hardeningmasticaroundoutsideedge
ofstandoff.Positionthestandoff/capassembly
inthecenterofthe111/2"squareholeandattach
toexteriorwallwithwoodscrewsprovided(see
Figure11).Thesidingstandoffmustsitush
againsttheexteriorfasciamaterial.
7.      
Pipe:Slidethewallrestopovertheventpipe
beforeconnectinghorizontalruntoventcap
(seeFigure12).
8. Carefullymovereplace,withventassembly
attached, toward wall and insert vent pipe
intohorizontaltermination.Thepipeoverlap
shouldbeaminimumof11/4"(seeFigure13,
page10).
9. Slidewall
restopagainstinteriorwallsurfaceandattach
withscrewsprovided.SeeFigure13,page10,
forhorizontalterminationdetails.
10. Place replace into position and shim with
noncombustible material if needed. Nail or
screwsideangestoframingtosecureunitin
place.IMPORTANT:Makesurereplaceis
levelbeforesecuring.Ifreplaceisnotlevel
itwillnotworkproperly.
Figure 10 - Installing Horizontal Vent Cap
(Noncombustible Exterior)
Wood Screw
Vent Cap
Figure 11 - Installing Siding Standoff
(Combustible Exterior Wall)
Cut Siding Away to
Fit Standoff
Wood
Screw
Screws
Standoff
Vent
Cap
Apply Mastic
to All Four Sides
Vent Cap
(Horizontal
Termination)
Interior Wall
Surface
Wall
Firestop
Horizontal
Vent Pipe
Figure 12 - Connecting Vent Cap with
Horizontal Vent Pipe
Screw

www.fmiproducts.com 118197-01D10
VENTINg INSTALLATION
INSTRUCTIONS
Continued
Figure 13 - Typical Horizontal
Termination Cap Mounting with
Additional Siding Standoff Installed
Siding Standoff
Screws
High Wind
Termination
Apply
Mastic to
Outside
Edge of
Standoff
Exterior Wall with Vinyl Siding
Maintain 1"
Minimum Air
Space Around
Outer Pipe When
Penetrating a Wall
Minimum Pipe
Overlap 11/4"
Wall
Firestop
Direct-Vent
Pipe

Figures 14 through 18 show different congura-
tionsandalternativesforventingwithhorizontal
termination. Each figure includes a chart with
criticalminimumandmaximumdimensionswhich
MUSTbemet.IMPORTANT:Ifusingaventing
congurationofonlyhorizontalventingwithno
verticalrun,a1/4"riseforevery12"ofruntoward
theterminationisrequired.

  
removable for vent inspection

WARNING: Never run vent
    
  

improperly installed and main-
   



RecommendedApplications:
• Installationusingcabinetsurrounds
• Throughthewallusingroundorsquaretermina-
tion(upto12"Adjustablepipe)
• NOTFORCORNERINSTALLATION
Horizontal
High Wind
Square
Termination
Wall Firestop
45° Elbow
Figure 14 - Horizontal Termination
Conguration for Square or Round
Terminations
45° Elbow
Wall
Firestop
Horizontal
Round
Termination
Exterior Portion
of Wall Firestop
(Round
Termination
Only)
Adjustable
Pipe 12" Max.
Round
Termination
Square Termination
 
32 3/4" min. 17" max.
* If installing this replace at altitudes of
4000 feet and above, it is recommended
that an additional vertical height of 6" be
added to the vent system.
111/2" X 111/2"
Frame Opening

www.fmiproducts.com
118197-01D 11

RecommendedApplications:
• Cornergroundoorinstallation
• Groundoorinstallationwherepipeventshorizon-
tallythroughwall(over12"horizontalpipe)
• Basementinstallationwhereonefootclearance
fromgroundtoterminationispossible
VENTINg INSTALLATION INSTRUCTIONS
Continued
Figure 15 - Horizontal Termination Conguration for Corner Installation Using One
90° Elbow
Square
Termination
Wall
Firestop
Not to Exceed (H) Limits
As Required
for (V), See
Chart for
Pipe Section
Required
45° Elbow
90° Elbow
90° Elbow
Square
Termination
Wall
Firestop
45° Elbow
12" Min.
Required
 Vertical Pipe 
*43 1/2" min. None 30" max.
54 1/2" min. 1 ft. 48" max.
66 1/2" min. 2 ft. 60" max.
78 1/2" min. 3 ft. 84" max.
90 1/2" min. 4 ft. 20' max.
* Ground Floor Corner Venting
Not to Exceed
(H) Limits

RecommendedApplications:
• Installationsrequiringaverticalriseonbuildingexterior
• Anyinstallationusingsnorkelterminationtoachieveonefootaboveground
Snorkelterminationsareavailableforinstallationsrequiringaverticalriseontheexteriorofthebuilding.
Ifinstallingsnorkelterminationbelowgrade,youmustprovideproperdrainagetopreventwaterfrom
enteringsnorkeltermination(seeFigure16).Donotbackllaroundsnorkeltermination.
Snorkel Termination
12"
Min.
Snorkel
Termination
Wall
Firestop
90° Elbow
45° Elbow
Figure 16 - Snorkel Termination Congurations for Below Ground Installation
Snorkel Termination
Adequate
Drainage
12" Min.
12" Min.

www.fmiproducts.com 118197-01D12
VENTINg INSTALLATION INSTRUCTIONS
Continued

 1
1
2
5' min. 2' max. 6' max.
6' min. 4' max. 12' max.
7' min. 6' max. 18' max.
8' min. 8' max. 20' max.
20' max. 8' max. 20' max.
Figure 17 - Horizontal Termination Conguration for Venting Using Two 90° Elbows
45° Elbow


Thefollowingcongurationsshowtheminimum
verticalriserequirementsforahorizontalsystem
usingtwo90°elbows.

 1
2
5' min. 6' max.
6' min. 12' max.
7' min. 18' max.
8' min. 20' max.
20' max. 20' max.
Figure 18 - Horizontal Termination Conguration for Venting Using Two 90° Elbows
with Termination at 90° with Fireplace
45° Elbow

www.fmiproducts.com
118197-01D 13


Note:Vertical restrictor must beinstalledinall
verticalinstallations.
1. Determine the route your vertical venting
willtake.Ifceilingjoists,roofraftersorother
framing will obstruct the venting system,
consideranoffset(seeFigure19)toavoidcut-
tingloadbearingmembers.Note:Payspecial
attentiontotheseinstallationinstructionsfor
requiredclearances(airspace)tocombustibles
whenpassingthroughceilings,walls,roofs,
enclosures,atticrafters,etc.Donotpackair
spaceswithinsulation.Alsonotemaximum
vertical rise of the venting system and any
maximumhorizontaloffsetlimitations.
2. Setthereplaceindesiredlocation.Dropa
plumblinedownfromtheceilingtotheposi-
tionofthereplaceexitue.Markthecenter
pointwheretheventwillpenetratetheceiling.
Drillasmalllocatingholeatthispoint.
 Dropaplumblinefromtheinsideoftheroof
tothelocatingholeintheceiling.Markthe
centerpointwheretheventwillpenetratethe
roof.Drillasmalllocatingholeatthispoint.

1. Cuta111/2"squareholeintheceilingusing
thelocatingholeasacenterpoint.Theopen-
ingshouldbeframedto111/2"x111/2"(29.21
cmx29.21cm)insidedimensions,asshown
inFigure9onpage8usingframinglumber
thesamesizeastheceilingjoists.Ifthearea
abovetheceilingisaninsulatedceilingoran
atticspace,nailrestopfromthetopside.This
preventslooseinsulationfromfallingintothe
requiredclearancespace.Iftheareaabovethe
ceilingisalivingspace,installrestopbelow
theframedhole.Therestopshouldbeinstalled
withnolessthanthreenailsperside(seeFigure
20).
2. Assemble the desired lengths of pipe and
elbowsnecessarytoreachfromthereplace
ueupthroughtherestop.Besureallpipe
andelbowconnectionsarefullytwist-locked
(seeFigure8,page8).
3. Cutaholeintheroofusingthelocatinghole
asacenterpoint. (Cover anyexposedopen
ventpipesbeforecuttingholein roof.)The
11 1/2" x 11 1/2" hole must be measured on
the horizontal; actual length may be larger
depending on the pitch of the roof. There
mustbea1"clearancefromtheventpipeto
combustiblematerials.Frametheopeningas
showninFigure9,page8.
4. Connect a section of pipe and extend up
throughthehole.
Note:Ifanoffsetisneededtoavoidobstruc-
tions,youmustsupporttheventpipeevery3
feet.Usewallstrapsforthispurpose(seeFig-
ure19).Wheneverpossible,use45°elbows
insteadof90°elbows.The45°elbowoffers
lessrestrictiontotheowof the ue gases
andintakeair.
VENTINg INSTALLATION
INSTRUCTIONS
Continued
Figure 19 - Offset with Wall Strap and 45°
Elbows
45° Elbow
Wall Strap
Roof Flashing
Ceiling Firestop
Figure 20 - Installing Firestop
If area above is a living space, install
restop below framed hole.
If area above is an attic space or insulated
area, install restop above framed hole.

www.fmiproducts.com 118197-01D14
5. Place the ashing over the pipe section(s)
extendingthroughtheroof.Securethebaseof
theashingtotheroofandframingwithroof-
ingnails.Besureroongmaterialoverlapsthe
topedgeoftheashingasshowninFigure19,
page13.Theremustbea1"clearancefrom
theventpipetocombustiblematerials.
6. Continuetoaddpipesectionsuntiltheheight
oftheventcapmeetstheminimumbuilding
coderequirementsdescribed inFigure7on
page6.Note:Youmustincreaseventheight
forsteeproofpitches.Nearbytrees,adjoining
rooines,steeppitchedroofsandothersimilar
factorsmaycausepoordraftordown-drafting
inhighwinds.Increasingtheventheightmay
solvethisproblem.
7. Twist-locktheventcapontothelastsection
ofventpipe.
Note:Iftheventpipepassesthroughanyoccupied
areasabovetherstoor,includingstoragespaces
and closets, you must enclose pipe. You may
frameandsheetrocktheenclosurewithstandard
construction material. Make sure and meet the
minimumallowableclearancestocombustibles.
Do not ll any of the required air spaces with
insulation.
VENTINg INSTALLATION
INSTRUCTIONS
Continued

Figures21through24 show four differentcon-
gurationsforverticaltermination.


1
2
5' min. 2' max.
6' min. 4' max.
7' min. 6' max.
8' min. 8' max.
20' max. 8' max.
Figure 21 - Vertical Venting
Conguration Using Two 90° Elbows
with Two Horizontal Runs (Vertical
Round High Wind Termination Shown)
Note: Install restrictor
into inner collar of
replace as shown.
45° Elbow

 
5' min. 2' max.
6' min. 4' max.
7' min. 6' max.
8' min. 8' max.
20' max. 8' max.
Figure 22 - Vertical Venting
Conguration Using One 90° Elbow
(Vertical Round High Wind Termination
Shown)
45° Elbow
Note: Install restrictor into
inner collar of replace as
shown.

www.fmiproducts.com
118197-01D 15
VENTINg INSTALLATION
INSTRUCTIONS
Continued
Note: Install
restrictor into
inner collar of
replace as
shown.

1 
5' min. 6' max.
6' min. 12' max.
7' min. 18' max.
8' min. 20' max.
Note: Vertical (V1) + Vertical (V2) = 40' max.
Figure 23 - Vertical Venting
Conguration Using Two 90° Elbows
(Vertical Round High Wind Termination
Shown)
45° Elbow

V = 40' max.
Figure 24 - Vertical Venting
Conguration With No Horizontal Run
(Vertical Round High Wind Termination
Shown)
Note: Install
restrictor into
inner collar of
replace as
shown.
45° Elbow

www.fmiproducts.com 118197-01D16




Number Description
P58-6 6" Section Double Wall Pipe,
Galvanized
P58-12 12" Section Double Wall Pipe,
Galvanized
P58-24 24" Section Double Wall Pipe,
Galvanized
P58-36 36" Section Double Wall Pipe,
Galvanized
P58-48 48" Section Double Wall Pipe,
Galvanized
PA58-712 Adjustable 7"-12" Section Double
Wall Pipe, Galvanized
E58-45 45° Elbow, Galvanized
E58-90 90° Elbow, Galvanized
VKG-58 Ground Floor Vent Kit, Galvanized
(Includes: 45° Elbow, 7"-12"
Adjustable Pipe, Wall Firestop,
Horizontal Square Termination,
16 Screws)
VKB-58 Basement Vent Kit, Galvanized
(Includes: 45° Elbow, 7"-12"
Adjustable Pipe, Wall Firestop,
Horizontal Square Termination,
4' Pipe, 90° Elbow, 20 Screws)
VKS-58 Snorkel Vent Kit, Galvanized
(Includes: 45° Elbow, 7"-12"
Adjustable Pipe, Wall Firestop,
36" Snorkel Termination, 4' Pipe,
1' Pipe, 90° Elbow, 26 Screws)
VKR-58 Roof Ven t K i t, G a l va n i zed
(Includes: 45° Elbow, 7"-12"
Adjustable Pipe, Flue Restrictor,
Vertical High Wind Termination,
2' Pipe, 4' Pipe, Wall Firestop,
Storm Collar, Roof Flashing
[0/12 - 6/12], 26 Screws)
VKC-58 Corner Vent Kit, Galvanized
(Includes 45° Elbow, 7"-12"
Adjustable Pipe, Wall Firestop,
Horizontal Termination, 6" Pipe,
90° Elbow, 18 Screws)
HHTK-58 High Wind Round Horizontal
Termination Kit
(Includes Round Termination,
VENTINg INSTALLATION
INSTRUCTIONS
Continued
Wall Firestop, 45° Elbow)
Number Description
HHT-58 High Wind Round Horizontal
Termination Kit, Galvanized
HTS-58 Horizontal Square Termination,
Galvanized
HTKS-58 Horizontal Square Termination Kit
(Includes: Square Termination,
Wall Firestop, 45° Elbow)
VT-58 Vertical Round Termination,
Galvanized
ST-58-14 14" Snorkel Termination,
Galvanized
ST-58-36 36" Snorkel Termination,
Galvanized
SC-58 Storm Collar, Galvanized
WF-58 Wall Firestop, Galvanized
RF-58-6 Roof Flashing - 0 to 6/12 Pitch,
Galvanized
RF-58-12 Roof Flashing - 6/12 to 12/12 Pitch,
Galvanized
VR-58 Vertical Restrictor, Galvanized
S-58 Vinyl Siding Standoff,
Galvanized
WS-58 Wall Strap
CS-58 Cathedral Ceiling Support
FP-58 Firestop Plate
SF-58 Stucco Flashing -
For use with HTS-58
RF-58 Flat Roof Flashing
REPLACEMENT PARTS
Note: Useonlyoriginalreplacementparts.This
will protect your warranty coverage for parts
replacedunderwarranty.

Contact authorized retailers of this product. If
theycannotsupplyoriginalreplacementpart(s),
callFMIPRODUCTS,LLC’sCustomerService
Departmentat1-866-328-4537.
Whencalling,haveready
• yourname
• youraddress
• modelandserialnumbersofyourreplace
• howreplacewasmalfunctioning
• typeofgasused(propane/LPornaturalgas)
• purchasedate
Usually,wewillaskyoutoreturntheparttothe
factory.

www.fmiproducts.com
118197-01D 17


-Filigree,Black
-Filigree,BrushedBrass
-Filigree,Platinum
RLD42-RolledLouver,Black
-Filigree,Black
-Filigree,BrushedBrass
-Filigree,Platinum


-BrushedBrass
-Platinum
-BrushedBrass
LT42P-Platinum


-Black(2"Brow)
-Black(2"Brow)


-Black
-BrushedBrass
-Platinum
PT42-Black
-BrushedBrass
PT42P-Platinum

Manualvariablecontrolbloweraccessoryprovides
better heat distribution. Complete installation
and operation instructions
includedinthismanual.


Provides better heat distribution. Blower turns
off and on automatically, as needed. Complete
installation and operation instructions included
inthismanual.

Contactauthorizedretailersofthisproduct.Ifthey
cannotsupplyoriginalreplacementpart(s),call
FMI PRODUCTS, LLC at 1-866-328-4537 for
referralinformation.
Whencalling,haveready
• modelnumberofyourreplace
• thereplacementpartnumber
TECHNICAL SERVICE
Youmayhavefurtherquestionsaboutinstallation,
operationortroubleshooting.Ifso,contactFMI
PRODUCTS, LLC’s Customer Service Depart-
ment at 1-866-328-4537. When calling, please
have your model and serial numbers of your
heaterready.
YoucanalsovisitFMIPRODUCTS,LLC’swebsiteat
.
ACCESSORIES
 All accessories may


Purchasethesereplaceaccessoriesfromyourlocal
retailer.Iftheycannotsupplytheseaccessories,
call FMI PRODUCTS, LLC’s Sales Department
at1-866-328-4537forinformation.Youcanalso
writetotheaddresslistedonthebackpageofthis
manual.


-TexturedRefractory
-StandardRefractory
-TexturedRefractoryHerringbone
-StandardRefractoryHerringbone
-TexturedRefractory
-StandardRefractory
-TexturedRefractoryHerringbone
-StandardRefractoryHerringbone
Thisbricklineraddsatouchofstyletoyourdirect-
ventreplace.Completeinstallationinstructions
includedinthismanual.
REPLACEMENT PARTS
Continued

www.fmiproducts.com 118197-01D18
ILLUSTRATED PARTS BREAkDOWN

6
7
10
17
18
13
2
12 19
8
1
4
11
9
14
3
16
5
15

www.fmiproducts.com
118197-01D 19
PARTS LIST

Thislistcontainsreplaceablepartsusedinyourreplace.Whenorderingparts,followtheinstructions
listedunderReplacement Parts onpage16ofthismanual.

  
110989-02 Left Refractory Brick Panel •1
111215-02 Left Refractory Brick Panel •1
111299-02 Left Refractory Brick Panel •1
111302-02 Left Refractory Brick Panel •1
110989-01 Left Refractory Brick Panel •1
111215-01 Left Refractory Brick Panel •1
111299-01 Left Refractory Brick Panel •1
111302-01 Left Refractory Brick Panel •1
110991-02 Rear Refractory Brick Panel •1
111217-02 Rear Refractory Brick Panel •1
111297-02 Rear Refractory Brick Panel •1
111330-02 Rear Refractory Brick Panel •1
110991-01 Rear Refractory Brick Panel •1
111217-01 Rear Refractory Brick Panel •1
111297-01 Rear Refractory Brick Panel •1
111300-01 Rear Refractory Brick Panel •1
110990-02 Right Refractory Brick Panel •1
111216-02 Right Refractory Brick Panel •1
111298-02 Right Refractory Brick Panel •1
111301-02 Right Refractory Brick Panel •1
110990-01 Right Refractory Brick Panel •1
111216-01 Right Refractory Brick Panel •1
111298-01 Right Refractory Brick Panel •1
111301-01 Right Refractory Brick Panel •1

    
1 ** ** Firebox Assembly 1
2 ** ** Face Weldment 1
3 108010-01 108328-01 Door Assembly 1
— 108328-02 Door Assembly (V Models Only) 1
4 108011-01 108331-01 Top Louver Assembly 1
5 108011-02 108331-02 Bottom Louver Assembly 1
6 ** ** Fireplace Top 1
7 ** ** Fireplace Top Insulation 1
8 ** ** Fireplace Surround 1
9 109082-01 109082-02 Heat Shield 1
10 24460 24460 Gas Conduit Assembly 1
11 See Below See Below Left Refractory Brick Panel 1
12 See Below See Below Rear Refractory Brick Panel 1
13 See Below See Below Right Refractory Brick Panel 1
14 108719-01 108455-01 Screen Rod 1
15 12105 107840-01 Screen 2
16 11418 11418 Push-On Nut 2
17 14123 14123 Strain Relief 1
18 21171 21171 Gas Knock-Out Cover 2
19 24353 24353 Handy Box Assembly 1
PARTS AVAILABLE - NOT SHOWN
27253 27253 Notice Label 1
55240 55240 Vent Label 1
** Part not available for eld replacement.









118197-01
Rev. D
03/10
WARRANTy
kEEP THIS WARRANTy
FMI PRODUCTS, LLC LIMITED WARRANTIES
New Products
Standard Warranty:FMIPRODUCTS,LLCwarrantsthisnewproductandanypartsthereoftobefreefromdefectsinmaterial
andworkmanshipforaperiodoftwo(2)yearsfromthedateofrstpurchasefromanauthorizeddealerprovidedtheproducthas
beeninstalled,maintainedandoperatedinaccordancewithFMIPRODUCTS,LLC’swarningsandinstructions.
Forproductspurchasedforcommercial,industrialorrentalusage,thiswarrantyis limitedto90 daysfromthedateofrst
purchase.
Factory Reconditioned Products
Limited Warranty:FMIPRODUCTS,LLCwarrantsfactoryreconditionedproductsandanypartsthereoftobefreefromdefects
inmaterialandworkmanshipfor30daysfromthedateofrstpurchasefromanauthorizeddealerprovidedtheproducthasbeen
installed,maintainedandoperatedinaccordancewithFMIPRODUCTS,LLC’swarningsandinstructions.
Terms Common to All Warranties
Thefollowingtermsapplytoalloftheabovewarranties:
Alwaysspecifymodelnumberandserialnumberwhencontactingthemanufacturer.Tomakeaclaimunderthiswarrantythebill
ofsaleorotherproofofpurchasemustbepresented.
Thiswarrantyisextendedonlytotheoriginalretailpurchaserwhenpurchasedfromanauthorizeddealer,andonlywheninstalled
byaqualiedinstallerinaccordancewithalllocalcodesandinstructionsfurnishedwiththisproduct.
Thiswarrantycoversthecostofpart(s)requiredtorestorethisproducttoproperoperatingconditionandanallowanceforlabor
whenprovidedbyaFMIPRODUCTS,LLCAuthorizedServiceCenteroraproviderapprovedbyFMIPRODUCTS,LLC.
Warrantypartsmustbeobtainedthroughauthorizeddealersofthisproductand/orFMIPRODUCTS,LLCwhowillprovide
originalfactoryreplacementparts.Failuretouseoriginalfactoryreplacementpartsvoidsthiswarranty.
Travel,handling,transportation,diagnostic,material,laborandincidentalcostsassociatedwithwarrantyrepairs,unlessexpressly
coveredbythiswarranty,arenotreimbursableunderthiswarrantyandaretheresponsibilityoftheowner.
Excludedfromthiswarrantyareproductsorpartsthatfailorbecomedamagedduetomisuse,accidents,improperinstallation,
lackofpropermaintenance,tampering,oralteration(s).
ThisisFMIPRODUCTS,LLC’sexclusivewarranty,andtothefullextentallowedbylaw;thisexpresswarrantyexcludesanyand
allotherwarranties,expressorimplied,writtenorverbalandlimitsthedurationofanyandallimpliedwarranties,includingwarran-
tiesofmerchantabilityandtnessforaparticularpurposetotwo(2)yearsonnewproductsand30daysonfactoryreconditioned
productsfromthedateofrstpurchase.FMIPRODUCTS,LLCmakesnootherwarrantiesregardingthisproduct.
FMIPRODUCTS,LLC’sliabilityislimitedtothepurchasepriceoftheproduct,andFMIPRODUCTS,LLCshallnotbeliable
foranyotherdamageswhatsoeverunderanycircumstancesincludingindirect,incidental,orconsequentialdamages.
Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylastsortheexclusionorlimitationofincidentalorconse-
quentialdamages,sotheabovelimitationorexclusionmaynotapplytoyou.
Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrightswhichvaryfromstatetostate.
Forinformationaboutthiswarrantycontact:
Model ( located on product or identication tag ) _____________________________
Serial No. ( located on product or identication tag ) __________________________
Date Purchased __________________________
Keep receipt for warranty verication.
2701 S. Harbor Blvd.
Santa Ana, CA 92704
1-866-328-4537
www.fmiproducts.com