Tempest Power Blower SS Series User manual

OWNER’S MANUAL
Power BlowersTM
Cone Air Flow (CAF) - Electric Driven
VSR SeriesVSG SeriesSS Series
(Incl. BASIC)
0216_01A

2
INTRODUCTION
ank you for choosing Tempest Technology Corporation for
your ventilation needs. With this manual we hope to help you
operate your Tempest product safely and to its full potential.
Maintained according to the specications set in this manual, it is
not uncommon to receive many years of use and operation out of
your Tempest equipment.
is manual is produced solely for the use of purchasers and
operators of Tempest Technology Corporation equipment. Any
reproduction, retransmission, or other use of the contents of
this manual without written consent of Tempest Technology
Corporation is strictly prohibited.
It is the intent of this manual to provide the owner/operator of
Tempest Technology Corporation products with both general and
specic information regarding the safe and proper operation and
maintenance of the equipment described within.
CONTACT
If aer careful review, any questions arise concerning any portion
of this manual, please contact Tempest Technology Corporation
for assistance:
TEMPEST TECHNOLOGY CORP.
4708 N. BLYTHE AVENUE
FRESNO, CA 93722
Toll Free: 800.346.2143
t: 559.277.7577
f: 559.277.7579
respon[email protected]m
www.tempest.us.com
TABLE OF CONTENTS
ABOUT TEMPEST 2
SAFETY GUIDE 3
GENERAL INFORMATION 3
POWER BLOWERTM DATA 4
POWER BLOWERTM INFORMATION 5
OPERATING PROCEDURES 5
MAINTENANCE PROCEDURES 7
POWER BLOWERTM TROUBLESHOOTING 7
REPLACEMENT PARTS - SINGLE SPEED 8
REPLACEMENT PARTS - SINGLE SPEED BASIC 9
REPLACEMENT PARTS - VSG & VSR 10
NOTES 11
WARRANTY BACK COVER
ABOUT TEMPEST
Tempest Technology Corporation is the leading manufacturer
of products and accessories for environmental management in
reghting and industrial applications.
Tempest began as a manufacturer of gasoline and electric powered
blowers for the re service. Fire departments use the Tempest
Power BlowerTM to provide “Positive Pressure Ventilation / Attack”
(PPV/PPA) to remove heat, gases and smoke from the interior of
a burning structure.
Tempest has expanded into other industries and found new
applications for its products. e Tempest Power BlowerTM and
PPV/PPA are used by industrial applications to control dust, fumes
and unhealthy gases like carbon monoxide, greatly improving
safety in conned spaces.
Tempest Technology Corporation has earned a reputation as a
leader and innovator in the air movement industry and continues
in that role today.
POSITIVE PRESSURE
VENTILATION/ATTACK

3
SAFETY GUIDE
Failure to follow the operating, maintenance and lubrication
requirements set forth in this manual may result in serious
personal injury or death and/or damage to equipment or property.
e following WARNING statements indicate potentially
hazardous conditions for operators and equipment. Make certain
that anyone who works on or around the blower has read and fully
understands the safety precautions listed.
1. Carefully read this owner’s manual before attempting to
operate, service or disassemble any part of your Tempest
Power BlowerTM.
2. DO NOT operate the unit when mentally or physically
fatigued or impaired.
3. Stay away from rotating parts; avoid wearing loose jackets,
shirts, and ties. Keep hands and feet away from moving parts.
4. Keep all unauthorized personnel at a safe distance from the
blower.
5. Keep all guards in place. DO NOT make repairs while the
unit is running. DO NOT operate if any guard or grille is not
in place.
6. Always wear eye protection. Loose debris can be picked up in
the air stream and own in the air.
7. Hearing protection is required. Engine and air noise may
exceed safe dB levels.
8. Always ensure proper voltage and amperage is delivered to
your Tempest Power BlowerTM.
9. Only a qualied technician should perform repairs or
maintenance on electric components.
10. Never operate your Tempest Power BlowerTM with electric
components exposed.
11. Never operate your Tempest Power BlowerTM with damaged,
exposed or frayed wiring.
12. It is the sole responsibility of the owner/operator to develop
procedures for proper use of the Tempest Power BlowerTM in
accordance with generally accepted ventilation techniques as
well as the organization’s own operating procedures, before
placing the unit into service.
GENERAL INFORMATION
BLOWER IDENTIFICATION
Each Tempest Power BlowerTM has a part number as well as a serial
number. e part number identies the type of unit (size, drive,
etc.) while the serial number relates to information referencing the
date of manufacture. is information is useful should it become
necessary to contact the factory regarding your Power BlowerTM.
SERIAL NUMBER LOCATIONS
e serial number is typically located on the frame just right of the
motor mount (when viewed from behind).
Please write the Serial Number of your Tempest Power BlowerTM
in the spaces below. is will aid us in identifying which model
you have when assisting you.
Model (Part No.)
Date
Serial No.
WARRANTY
Warranty information on your unit can be found on the back page
of this manual. For further information, please contact Tempest
Technology Corp.

4
POWER BLOWERTM DATA
Positive Pressure Ventilation Fan, Cone Air Flow (CAF)
Single Speed (Incl. BASIC) Models: Direct-Drive Single Speed 110-120V, 60Hz or 220-230V, 50Hz
Electric Motor, GFCI Compatible
VSG & VSR Models: Direct-Drive Variable Speed 110-120V, 60Hz (or 220-230V, 50Hz, VSR only)
Electric Motor, GFCI Compatible, NEMA-4 Rated Drive
Hazardous Locations Class I, Group C & D and Class II, Group F & G Environments
AirFlex Fiberglass Reinforced Polyamide Blades
Keyed Sha and Set or Cap Screws
Turbo 2000 Tapered Aluminum w/ Durable Powder-Coat Finish
Rugged, Lightweight, Square-Steel Tubing with Powder-Coat Finish
Foot-Operated Tilt Mechanism
16” Models: Four Position Tilt, +10°, +5°, 0°, -5°
18”, 21”, 24” Models: Five Position Tilt, +15°, +10°, +5°, 0°, -5°
18”, 21” BASIC Models: ree Position Tilt +15°, +10°, 0° (Hand-Operated)
Continuous Circular-Wound, External-Weld Steel Wire with 8 Tie Points for Additional Safety
Meets UL & European CE Safety Standards
Steel-Reinforced Rubber and Welded Steel Spring Feet
16” Models: 6” Non-Pneumatic w/ Steel Hubs
18”, 21”, 24” Models: 8” Non-Pneumatic w/ Steel Hubs
TYPE:
DRIVE:
EP OPTION:
BLADE:
BUSHING:
SHROUD:
FRAME:
TILT MECHANISM:
GRILLE:
VIBRATION DAMPENERS:
WHEELS:
(NON BASIC)
SS SPECIFICATIONS:
SS BASIC SPECIFICATIONS:
VSG SPECIFICATIONS:
VSR SPECIFICATIONS: Model No. Part No. Size HP CFM Dimensions (WxDxH) Weight
VS-16-R-2.0 910-1400 16” 2.0 11,551
21.00” x 19.75” x 23.00” 98 lbs.
VS-18-R-2.0 910-1420 18” 2.0 12,839
23.00” x 21.00” x 24.25” 104 lbs.
VS-21-R-2.0 910-1440 21” 2.0 14,836
26.00” x 21.00” x 26.25” 108 lbs.
VS-24-R-2.0 910-1460 24” 2.0 15,663
29.50” x 21.00” x 30.00” 119 lbs.
Model No. Part No. Size HP CFM Dimensions (WxDxH) Weight
SS-16-S-1.5 910-1200 16” 1.5* 11,804
20.50” x 19.75” x 21.75” 74 lbs.
SS-18-S-1.0 910-1220 18” 1.0 8,748
22.00” x 21.00” x 24.25” 76 lbs.
SS-21-S-1.0 910-1240 21” 1.0 11,698
24.75” x 21.00” x 26.25” 81 lbs.
SS-24-S-1.0 910-1260 24” 1.0 12,867
28.00” x 21.00” x 30.00” 90 lbs.
Model No. Part No. Size HP CFM Dimensions (WxDxH) Weight
SS-18-S-1.0 BASIC 910-1222 18” 1.0 8,748
22.00” x 18.00” x 24.00” 57 lbs.
SS-21-S-1.0 BASIC 910-1242 21” 1.0 11,698
25.00” x 18.00” x 25.50” 60 lbs.
Model No. Part No. Size HP CFM Dimensions (WxDxH) Weight
VS-16-G-1.5 910-1300 16” 1.5 11,125
21.00” x 19.75” x 21.75” 89 lbs.
VS-18-G-1.5 910-1320 18” 1.5 11,861
23.00” x 21.00” x 24.25” 95 lbs.
VS-21-G-1.5 910-1340 21” 1.5 13,414
26.00” x 21.00” x 26.25” 99 lbs.
VS-24-G-1.5 910-1360 24” 1.5 12,901
29.50” x 21.00” x 30.00” 109 lbs.
*16” EP models come with 1.0 HP motor

5
POWER BLOWERTM INFORMATION
e Tempest Power BlowerTM is a high powered, portable
fan used for Positive Pressure Ventilation and Attack (PPV/
PPA), ventilation techniques that quickly and eciently replace
hazardous interior environments with clean, cool air.
PPV and PPA were pioneered in the reghting industry where
reghters use the Tempest Power BlowerTM to ventilate smoke,
heat, and harmful gases from buildings. is creates a safer
environment for them to work in and makes it easier for them to
nd victims and extinguish the re.
PPV and PPA rely on two principles, (1) an air pattern capable of
creating an eective door seal, and (2) pressure. To accomplish
Positive Pressure Ventilation or Attack, the blower is placed on
the outside of the structure. It is positioned so that the air pattern
created by the blower completely seals the entrance opening, or
at least 2/3 of it. When this seal is achieved, the air pressure is
increased equally at all points inside the structure. When an
exhaust opening is created, all of the interior air moves in one
mass towards it. e result is fast, ecient ventilation of the entire
structure.
NOTE: e Tempest Power BlowerTM is the most ecient
tool for PPV and PPA for two reasons. First, the exclusive
Tempest Turbo 2000 aluminum shroud design creates a
broad, cone shaped air pattern. Second, the airex impeller
used on all Tempest blowers is designed to create high
pressure. ese two features working together make the
Tempest Power BlowerTM a highly eective and ecient
ventilation tool.
As with any new technique, Positive Pressure Ventilation requires
training and education in order to be implemented properly
and safely. Tempest oers access to a complete line of training
materials, which cover many applications for this powerful
ventilation technique. For more information visit www.tempest.
us.com, www.positivepressuretraining.com or contact us at
800.346.2143 or [e-mail].
OPERATING PROCEDURES
PRE-OPERATION
Aer receiving and unpacking your blower, be sure to carefully
inspect it for any damage that might have occurred during shipping.
Should you nd any damage: PLEASE NOTIFY TEMPEST
TECHNOLOGY CORP. IMMEDIATELY AT 800.346.2143 OR
[e-mail].
OPERATION
SET-UP, STARTING AND STOPPING
Assuming the previous Pre-Operation and safety instructions
have been followed, the blower is now ready to run.
WHEN USING A GENERATOR, IT IS IMPERATIVE
THAT THE GENERATOR BE RUNNING AT FULL
CAPACITY BEFORE PLUGGING IN ANY ELECTRIC
BLOWER. ALWAYS VERIFY SUFFICIENT GENERATOR
OUTPUT BEFORE USE. IMPROPER VOLTAGE SUPPLY
MAY DAMAGE UNIT AND VOID WARRANTY.
CAUTION: DO NOT MOVE THE BLOWER WHILE
IT IS IN OPERATION. SEVERE PERSONAL INJURY IS
POSSIBLE AS WELL AS DAMAGE TO THE BLOWER.
ALWAYS SHUT-DOWN THE BLOWER PRIOR TO
MOVING.
SET-UP
Position the blower in the desired location, making sure it is
placed on a at, hard and debris free surface.
NOTE: e following sections cover separate operating
instructions for each type of electric blower. Please be sure to
follow the operating instructions specic to your particular
blower model. (ex. VSG, VSR, Single Speed)
STARTING - SINGLE SPEED
No Switch: Plug blower into power source. Unit will begin
running automatically.
With Switch:
1. Ensure blower toggle is switched to the OFF position.
2. Plug blower into power source.
3. Switch toggle to the ON position.
STOPPING
No Switch: Unplug unit from power source or switch o power
source.
With Switch: Stop unit before unplugging from power source.
Make sure toggle switch is set to STOP.

6
SINGLE SPEED REQUIREMENTS
Based on 110-120V fan on 20 amp circuit.
Motor HP 0.3 1.0 1.5
Starting Amps 10.9 48.0 54.6
Starting Watts 1300 6,000 6,300
Runnings Amps 6.3 13.4 14.2
Runnings Watts 756 1,900 2,100
MAXIMUM POWER CORD LENGTH
Based on 1 fan on 20 amp circuit.
Motor HP 0.3 1.0 1.5
14 Gauge 215’ 60’ 45’
12 Gauge 330’ 95’ 65’
10 Gauge 550’ 150’ 115’
8 Gauge 850’ 240’ 190’
6 Gauge 1,350’ 380’ 300’
STARTING - VSG & VSR
1. Check that the toggle switch is set to STOP.
2. Plug the blower cord into power source receptacle. If power is
properly brought to the control, the “ON” or “POWER” LED
and the “STOP” or “STATUS” LED indicators will be lit.
3. Engage START toggle. e toggle is momentary switch to
start. e center position is the run location.
4. Adjust the rheostat knob to the desired speed/load.
STOPPING
1. Stop unit before unplugging from power source. Make sure
toggle is set to STOP.
NOTE: VSR & VSG GFCI systems are set to run on the cord
length and size specied at the time of purchase (options listed
below). If you wish to run the unit on a dierent size/length
cord than originally requested, the fan’s drive may need to be
reset. For information on how to adjust the set cord length
and size, please contact Tempest Technology Corp. e VS-
24-G-1.5 is only available in A or B conguations.
A) 15’ of 12 AWG
B) 200’ of 10 AWG
C) 200’ of 12 AWG
D) 200’ of 14 AWG
p/n 400-090
Label must be printed on UL approved stock
Label material (10 mil Velvet Polished Polycarbonate
w/Selective Permanent Adhesive)
Label part number: A45479
Printing Notes:
Printed label must be RoHS Compliant
White = 0% K
Black = 100% K
VSR DRIVE VSG DRIVE

7
MAINTENANCE PROCEDURES
Although Tempest electric Power BlowersTM are designed to
eliminate most maintenance issues, it is imperative that the
blowers be inspected before startup on each use. Please review the
following list before using this product.
MAINTENANCE SCHEDULE
EVERY USE
• INSPECT BLOWER FOR DAMAGE AND FIX IF
ANY
• TIGHTEN/REPLACE ANY LOOSE OR MISSING
PARTS
EVERY MONTH OR 10 HOURS
• INSPECT & CLEAN SHROUD & GRILLES
IMPORTANT: Always operate the blower in an area free
of debris which may be pulled into the unit’s blades. If you
suspect the fan’s blade may have contacted a hard object,
thorough inspection of the blade assembly should be
conducted immediately to ensure safety. You may contact
Tempest Technology Corp. in order to nd out how to
properly inspect the blade assembly.
POWER BLOWERTM TROUBLESHOOTING
Various factors can contribute to or be the sole cause of problems
for electric power blowers. is section will identify some of these
problems and provide solutions to correct them.
BLOWER MOVEMENT OR “WALKING”
• Adjust the rubber footpads on the back of the blower by
turning them either in or out.
• Adjust the side that is walking. is will help to evenly
distribute the weight of the blower to all four points of the
frame.
• Most blowers will walk if not running at full speed, make sure
the blower is running at full speed.
• Ensure the blower is sitting at and not on small rocks or
other objects.
• If blower is still walking, contact Tempest at 800.346.2143 or
respon[email protected]m.
SINGLE SPEED
BLOWER FAILS TO START
• Make sure the unit is connected to the power source.
• oroughly check the power cord. If the cord shows any signs
of serious wear it may need to be replaced before running
properly.
• Many blowers are equipped with an “automatic reset.” is
reset will kill power to the blower when the unit is at risk of
overheating. Let the blower cool and attempt to start it again.
• ere may be damage to the internal wiring. Have a qualied
technician or electronics specialist examine the blower
circuitry and wiring and make any necessary repairs.
• If your Tempest Single Speed blower is not running aer
pursuing the steps mentioned above, please contact us at
800.346.2143 or [e-mail].
VSG & VSR
IF THE “ON” AND THE “STOP” OR “STATUS” LEDS DO
NOT LIGHT UP
• Make sure the unit is connected to the power source.
• Conrm that adequate power is being supplied to blower. If
power supply is adequate, DISCONNECT BLOWER FROM
POWER SOURCE and check for loose or faulty wiring on
blower electrical system and have a qualied professional
perform repairs if needed.
• Connect blower to power source and attempt restarting. If
blower still does not run, contact Tempest at 800.346.2143 or
respon[email protected]m.
BLOWER SURGES WHEN RUNNING ON GENERATOR:
• Check that the generator meets the proper voltage output to
operate the blower.
• If blower is still surging, contact Tempest at 800.346.2143 or
respon[email protected]m.

8
Standard Motor SS-16-S-1.5 SS-18-S-1.0 SS-21-S-1.0 SS-24-S-1.0
910-1200 910-1220 910-1240 910-1260
Explosion Proof (EP) Motor SS-16-S-1.0-EP SS-18-S-1.0-EP SS-21-S-1.0-EP SS-24-S-1.0-EP
910-1201 910-1221 910-1241 910-1261
Item # Description Part No. Part No. Part No. Part No.
11/4 X 1/2 FLAT SOC C/S ZINC 100-079 100-079 100-079 100-079
2WASHER 3/8 X 2 FENDER HVY Z 120-037 120-037 120-037 120-037
3HANDLE BRACKET 220-069 220-069 220-069 220-069
4GRIP BASIC BLOWER HANDLE 220-248 220-248 220-248 220-248
5WHEEL FLAT FREE 240-008 240-012G 240-012G 240-012G
6SPRING TORSION 300-019 300-018 300-018 300-018
7SPRING PLUNGER W/HANDLE 300-170 300-170 300-170 300-170
8FOOT TAPERED 580-006 580-006 580-006 580-006
9SPRING ASSEMBLY 600-001 600-001 600-001 600-001
10* ELECTRIC MOTOR ASSEMBLY STD 600-135 600-131 600-131 600-131
11* ELECTRIC MOTOR ASSEMBLY EP 600-132 600-132 600-132 600-132
12* HANDLE YELLOW 600-715K 600-716K 600-717K 600-718K
13* WIN STEP YELLOW 600-719K 600-720K 600-721K 600-722K
14* LEG ASSEMBLY LEFT DARK GREY 610-1001K 610-1020K 610-1020K 610-1020K
15* LEG ASSEMBLY RIGHT DARK GREY 610-1002K 610-1021K 610-1021K 610-1021K
16* FRAME DARK GREY 610-1300K 610-1320K 610-1340K 610-1360K
17 FRONT GRILLE DARK GREY 610-1400K 610-1420K 610-1440K 610-1460K
18 REAR GRILLE DARK GREY 610-1401 610-1421 610-1441 610-1461
19* SHROUD, YELLOW 705-101 705-106 705-111 705-116
20* BLADE ASSEMBLY STD MODELS 705-278 705-284 705-264 705-268
20* BLADE ASSEMBLY EP MODELS 705-292 705-284 705-264 705-268
* denotes item includes necessary hardware for installation
NI not Illustrated
This document contains proprietary information and intellectual property that cannot be reproduced or altered, in whole or in part, without the written consent of Tempest Technology Corp.
Copyright 2016 - All Rights Reserved
Information and Material Subject to Change Without Notice
Drawn By Bill Allen Rev. 0116_01A
Replacement Parts
Single Speed Electric
Power Blowers
™
For Technical Support;
1-800-346-2143
[email protected]
Please specify part number and
serial number of blower when
ordering parts.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

9
SS-18-S-1.0 BASIC SS-21-S-1.0 BASIC
910-1222 910-1242
Item # Description Part No. Part No.
1WASHER 3/8 X 2 FENDER HVY Z 120-037 120-037
2FOOT TAPERED 580-006 580-006
3SPRING & FOOT ASSY, COMPLETE 600-001 600-001
4* ELECTRIC MOTOR ASSEMBLY 600-131 600-131
5BASIC TILT CAM ASSEMBLY 600-345K 600-345K
6* LEG KIT LEFT/RIGHT DARK GREY 610-1027K 610-1027K
7* FRAME DARK GREY 610-1304K 610-1344K
8FRONT GRILLE DARK GREY 610-1420K 610-1440K
9REAR GRILLE DARK GREY 610-1421 610-1441
10* SHROUD, RED 705-105 705-110
11* BLADE ASSEMBLY 705-286 705-282
Handle/Wheel Kit
610-1921
Item # Description Part No.
12 WHEEL 715-OF 7X1.50 OFFSET 240-001
13 HANDLE RECEIEVER ASSY 18 & 21 BASIC 610-1659
14 PULL UP HANDLE FOR BASIC 600-286K
15 BASIC WHEEL MOUNT LEFT 610-1657
16 BASIC WHEEL MOUNT RIGHT 610-1658
* denotes item includes necessary hardware for installation
NI Not Illustrated
This document contains proprietary information and intellectual property that cannot be reproduced or altered, in whole or in part, without the written consent of Tempest Technology Corp.
Copyright 2016 - All Rights Reserved
Information and Material Subject to Change Without Notice
Drawn By Bill Allen Rev. 0116_01A
Replacement Parts
Single Speed Basic Electric
Power Blowers
™
For Technical Support;
1-800-346-2143
[email protected]m
Please specify part number and
serial number of blower when
ordering parts.
9
1
2
3
5
6
7
8
10
11
12
13
14
15
16
4

10
VS-16-R-2.0 VS-18-R-2.0 VS-21-R-2.0 VS-24-R-2.0 VS-16-G-1.5 VS-18-G-1.5 VS-21-G-1.5 VS-24-G-1.5
910-1400 910-1420 910-1440 910-1460 910-1300 910-1320 910-1340 910-1360
Item # Description Part No. Part No. Part No. Part No. Part No. Part No. Part No. Part No.
11/4 X 1/2 FLAT SOC C/S ZINC 100-079 100-079 100-079 100-079 100-079 100-079 100-079 100-079
2WASHER 3/8 X 2 FENDER HVY Z 120-037 120-037 120-037 120-037 120-037 120-037 120-037 120-037
3HANDLE BRACKET 220-069 220-069 220-069 220-069 220-069 220-069 220-069 220-069
4GRIP BASIC BLOWER HANDLE 220-248 220-248 220-248 220-248 220-248 220-248 220-248 220-248
5WHEEL FLAT FREE 240-008 240-012G 240-012G 240-012G 240-008 240-012G 240-012G 240-012G
6SPRING TORSION 300-019 300-018 300-018 300-018 300-019 300-018 300-018 300-018
7SPRING PLUNGER W/HANDLE 300-170 300-170 300-170 300-170 300-170 300-170 300-170 300-170
8FOOT TAPERED 580-006 580-006 580-006 580-006 580-006 580-006 580-006 580-006
9* VSR OR VSG DRIVE 581-182K 581-182K 581-182K 581-182K 581-180K 581-180K 581-180K 581-180K
10 SPRING ASSEMBLY 600-001 600-001 600-001 600-001 600-001 600-001 600-001 600-001
11* ELECTRIC MOTOR ASSEMBLY 600-144 600-144 600-144 600-144 600-140 600-140 600-140 600-140
12* HANDLE YELLOW 600-715K 600-716K 600-717K 600-718K 600-715K 600-716K 600-717K 600-718K
13* WIN STEP YELLOW 600-719K 600-720K 600-721K 600-722K 600-719K 600-720K 600-721K 600-722K
14* LEG ASSEMBLY LEFT DARK GREY 610-1001K 610-1020K 610-1020K 610-1020K 610-1001K 610-1020K 610-1020K 610-1020K
15* LEG ASSEMBLY RIGHT DARK GREY 610-1002K 610-1021K 610-1021K 610-1021K 610-1002K 610-1021K 610-1021K 610-1021K
16* FRAME DARK GREY 610-1303K 610-1323K 610-1343K 610-1363K 610-1303K 610-1323K 610-1343K 610-1363K
17 FRONT GRILL DARK GREY 610-1400K 610-1420K 610-1440K 610-1460K 610-1400K 610-1420K 610-1440K 610-1460K
18 REAR GRILL DARK GREY 610-1401 610-1421 610-1441 610-1461 610-1401 610-1421 610-1441 610-1461
19* SHROUD YELLOW 705-102 705-107 705-112 705-117 705-102 705-107 705-112 705-117
20* BLADE ASSEMBLY 705-273 705-276 705-267 705-269 705-274 705-277 705-281 705-288
* denotes item includes necessary hardware for installation
NI Not Illustrated
This document contains proprietary information and intellectual property that cannot be reproduced or altered, in whole or in part, without the written consent of Tempest Technology Corp.
Copyright 2016 - All Rights Reserved
Information and Material Subject to Change Without Notice
Drawn By Bill Allen Rev. 0116_ 01A
Replacement Parts
VSR and VSG Electric
Power Blowers™
For Technical Support;
1-800-346-2143
[email protected]
Please specify part number and
serial number of blower when
ordering parts.
20
7
12
16
31
4
9
VSG Drive
VSR Drive
VSG Motor
VSR Motor
18
11
2
8
13
10
6
5
15
14
19
17

11
NOTES

Except as otherwise set forth below, any claim by Customer with reference to the Goods sold shall be
deemed waived by the Customer unless submitted in writing to Tempest within the earlier of (i) ve
(5) business days following the date Customer discovered, or by reasonable inspection should have
discovered, any claimed breach of the foregoing warranty, or (ii) thirty (30) calendar days following the
date of shipment. Any cause of action for breach of the foregoing warranty shall be brought within one
(1) year from the date the alleged breach was discovered or should have been discovered, whichever
occurs rst.
Limited Power Blower Warranty
Tempest warrants to the original purchaser that all Tempest gasoline and electric powered blowers
(except the engine or motor and drive) will be free from original defects in workmanship and material,
under normal-use conditions, and Tempest will replace any defective power blower part (except the
engine or motor and drive) if returned during the applicable warranty period, for the time frame
indicated below:
Firefighting Industry:
Five (5) years from date of shipment
Industrial/Rental Industry:
One (1) year from date of shipment
Blower Engine / Motor & Drive Warranty
e engines manufactured by Honda® and Briggs & Stratton® are covered by a separate manufacturer’s
warranty for a period of two (2) years. Electric motors manufactured by Magnetek, Marathon, Baldor,
Franklin Electric and Multi-Fan are covered by a separate manufacturer’s warranty for a period of one
(1) year.
Note: Unauthorized repair or modication of the factory assembly or parts voids the warranty.
All information provided in this operations manual is subject to change without notice. Please refer to
our website for the most recent sales terms and conditions.
WARRANTY INFORMATION
Tempest Technology Corporation
4708 N. Blythe Avenue, Fresno, CA 93722
t: 559.277.7577 • f: 559.277.7579 • [e-mail]
www.tempest.us.com