MV1200A_1210A_1220A-SETUPGUIDE-E-3.DOCX
/MULTI
VIDEO
/AUDIO
ALL OUT
OP OUT3 OP OUT4 USER4
USER3
USER2USER1
SDI OUT
AUTO
FULL (MUTE) ENTER
(LOCK) (TEST)
MENU
HDMI OUT
/OP OUT2/OP OUT1
1 2 3 4 5 6 7 8
910 11 12 13 14 15 16
MV-1200
MULTI VIEWER
ON
OFF
POWER 1 POWER 2
POWER 1
POWER 2
FAN
ALARM
GENLOCK
MV-1200A/1210A/1220A
Quick Setup Guide
Connection and System Configuration
Setup Procedure
The procedure is shown numbered in the above figure.
1Apply DC power to the MV-1200A/ MV-1210A Main Unit using the supplied AC cord.
Secure the cord with the supplied AC cord retaining clip.
Ground the unit for your safety.
2Connect an SDI monitor. (MV-1210A/1220A only)
3Connect an HDMI monitor. (MV-1200A/1220A only)
4Connect signal source devices, such as video cameras.
5Connect a PC to be used for remote control to the Main Unit LAN connector using a
LAN cable.
6Change the PC network settings for the connection with the Main Unit.
192.168.0.yyy (yyy is any number from 1 to 24
except for the number set for the Main Unit and
gateway number.)
* The Main Unit IP address can be changed in the Main Unit menu or Layout
Manager. 192.168.0.10 is the default IP address.
7Verify outputs to the SDI monitor, HDMI monitor and audio devices using test signals.
1) Hold down the (TEST) button for it to flash amber so that a test signal is output.
(See the table below. 1 is the default format test signal)
2) The format can be switched by selecting 1 - 8 button directly.
3) Hold down the (TEST) button for it to switch to dim right (green) to exit
HDMI/SDI/AUDIO test signal selection mode.
* MV-12PCO required
Front Panel
8Install Layout Manager from the supplied CD.
1) Install the software, then double-click on the [MV-1200 Series Layout Manager]
icon to launch the Layout Manager.
2) Press the Online/Offline button in the upper left corner of the main window.
3) The connection dialog appears. Enter the Main Unit IP address, (default:
192.168.0.10), then click OK.
* Note that ID and password protection is not active at the first time.
* If the connection cannot be established, check the LAN connection and the PC
network settings.
9If you are using a monitor other than SDI: 1080/59.94i or HDMI: 1080/59.94p, set
frequency and Interlaced/Progressive. Click the Controller (9) button, then click
Output Format (9-①) to open the menu page. Set frequency and
Interlaced/Progressive in the page.
10 Select SDI/COMPOSITE for the signal input as shown below.
Input signals are displayed in windows in the 4-split screen in 2K format. Click the
Controller (9) button then click the Screen Select button to open the dialog. Click the
Preset02 (10-①) in the dialog then return to the main page then click Input Setting
(10-②) to open the dialog. Click the Input Select button (10-③) in the dialog to
select SDI or COMPOSITE for each input, then click OK.
If Nothing Appears on the Monitor!
Check to see if the monitor has been properly connected. If nothing still appears on the
monitor, check the monitor’s specification sheet to see if the monitor supports any of the
formats listed in the left table.
Packing List：In case of standard configuration
MV-1200A, MV-1210A or MV-1220A (1), Quick Setup Guide(1),
CD-ROM (Installation CD 1 including User Manuals),
AC cord (1), AC cord retaining clip (1 set),
HDMI Cable Lacing Bracket (1set) (MV-1200A/1220A only),
Rack mount bracket set (1 set), Rubber feet (1 set)
Use SDI or HDMI monitors that
support 1920 x 1080 (59.94 or 50)
interlaced or progressive video
signals, or 1280 x 720 (59.94 or
50) progressive video signals
support monitors.
3G/HD-SDI OUTPUT:
Connect a monitor that
supports 3G/HD-SDI
LAN：Connect a PC to run the supplied software programs.
Layout Manager
・To control overall system
・To create/edit layouts
・To edit/save logos
Live Viewer
(To output video
Signal to PC)
* If in 1920 x 1080 mode
Interlaced / Progressive selection
Test
Signal
Output
HDMI
/SDI
/AUDIO
3G/HD/SD-SDI/COMPOSITE INPUT:
Connect cameras, switchers, etc. to input video sources
Connect HDMI/DVI/PC
input, and etc.
ALARM OUT:
4-pin ALARM
(PS1/PS2/FAN/COM )
AUDIO OUT:
For analog
audio output
3G/HD/SD-SDI/COMPOSITE
INPUT1-4:
Connect cameras, switchers,
etc. to input video sources.
HDMI OUTPUT:
Connect a monitor that
supports 1080/59.94p.
RS-232C/422/485:
Connect a PC for
remote control.
GPIO:
For layout switching
and tally output
AUTO button:
Starts auto
sequence.
VIDEO/AUDIO button:
Switches Video/Audio
operation
MENU button:
Hold down: Menu display
Normal: Moves to upper menu
ENTER（LOCK）button:
Hold down: Locks the
front panel operation.
button
Hold down:
Test signal output
menu
HDMI INPUT1-4:
Connect HDMI/DVI/PC input.
/MULTI
VIDEO
/AUDIO
ALL OUT
OP OUT3 OP OUT4 USER4
USER3
USER2USER1
SDI OUT
AUTO
FULL (MUTE) ENTER
(LOCK) (TEST)
MENU
HDMI OUT
/OP OUT2/OP OUT1
1 2 3 4 5 6 7 8
910 11 12 13 14 15 16
MV-1200
MULTI VIEWER
ON
OFF
POWER 1 POWER 2
POWER 1
POWER 2
FAN
ALARM
GENLOCK
AC100-240V 50/60HzIN
1 2 3 4
LAN
L/R
HDMI OUTPUTHDMIINPUT
4321
3G/HD-SDI
OUTPUT
3G/HD/SD-SDI,COMPOSITE INPUT
SER.NO.
3G/HD/SD-SDI,COMPOSITE INPUT S/No.
MV-12SDI
RS-232C-422/485
S/No.
GPIO LTC REF
MV-12IF
21 3 4
1 2 3 4
S/No.
S/No.
MV-12PCO
DC12V IN
MV-12PCI
HDMI OUTPUT
HDMIINPUT
1 2 3 4
AUDIO
OUT ALARM
OUT
3G/HD/SD-SDI/COMPOSITE
INPUT1-8:
Connect cameras, switchers, etc.
to input video sources.
3G/HD-SDI OUTPUT1-2:
Connect a monitor that
supports 3G/HD-SDI
HDMI OUTPUT:
Connect a monitor that
supports 1080/59.94p.
You can download manuals and other documents by registering your email address.
